Code Alarm CSI-300 инструкция обслуживания

128- 1 OF 12 Model CSI-300 Owner ’s Manual 4 Button Remote Security System with Dual Stage Shock Sensor IMPORT ANT ! In order to provide the highest possible level of security to your vehicle, this system is equipped with selectable manual override circuitry . It is possible that you will need to manually override your security system if the tran[...]

128- 2 OF 12 Page 2 YOUR “ Code Hopping “ TRANSMITTERS The transmitters included with your new security system use the most advanced and secure form of radio frequency transmission available on any current automotive security system. Some of today’s sophisticated auto thieves use a device known as a code grabber , which will receive and store[...]

128- 3 OF 12 Page 3 SILENT ARMING - ACTIVE 1. Turn off the engine, exit the vehicle, and close all doors, hood lid, and trunk lid. 2. Press and hold the Lock button on the keychain transmitter for 2 seconds. ; Dash mounted LED begins to flash slowly . ; Parking Lights flash two times. ; Siren will not sound. If the siren "chirped" four ti[...]

128- 4 OF 12 Page 4 ; Whenever the system is armed, the dash mounted LED indicator will slowly flash. This serves as a visual deterrent to the potential thief. The LED is a very low current bulb and will not cause the vehicle’s battery to drain, even when left unattended for extended periods. ; Whenever the system is triggered, the vehicle’s pa[...]

128- 5 OF 12 Page 5 SILENT DISARMING 1. As you approach the vehicle, press and hold the Unlock button on the keychain transmitter for 2 seconds. ; Dash mounted LED turns off. If passive arming was selected during the installation, then the LED will start flashing rapidly , indicating that the system is rearming automatically . Open any door to susp[...]

128- 6 OF 12 Page 6 p If the LED is flashing three times...pause...three times...pause...etc., then an intrusion attempt was made through one of the vehicle’s doors. These intrusion warning indicators are stored in the system’s memory and will only be erased when the ignition key is turned on. V ALET SWITCH The valet switch allows you to tempor[...]

128- 7 OF 12 Page 7 1 . Disarm the system by use of the transmitter , or by use of the emergency override sequence. Turn the ignition switch to the on position. 2. Within 10 seconds, press and release the valet/override switch, 3 times. 3. Within 10 seconds turn the ignition switch off, on, off, on, off, on. (The siren or horn will beep and the lig[...]

128- 8 OF 12 Page 8 NOTE: If after step 8, the LED flashes a code other than what was just entered, this indicates that the code has not been changed. Y ou will have to repeat steps 1 through 7 above being certain to note the following: Acceptable digits 10ths or units are 1 through 9. The unit will not recognize a 0 (Zero), or no digit entered in [...]

128- 9 OF 12 during the Panic sounding period. 3. During the panic mode, the Lock and Unlock buttons can be used to lock and unlock the doors, (if the option is installed), however once the unlock/disarm button is pressed, the vehicle's starter inhibit device, (where installed) will be disabled allowing the vehicle to start. ADDITIONAL REMOTE [...]

128- 10 OF 12 Page 10 Check with your installation center for more information on the optional accessory that may have been installed and how it is accessed, as the transmitter buttons must be programmed to access this option if installed. IGNITION CONTROLLED LOCK UNLOCK: (Unlock Drivers Only , or Unlock All Doors) Y our security system has a selec[...]

128- 11 OF 12 CSI-300 SYSTEM FUNCTIONS A T A GLANCE DASH LED INDICA TORS RAPID FLASHING = P ASSIVE ARMING SLOW FLASHING = ARMED OFF = DISARMED ON SOLID = V ALET MODE 3 FLASH...P AUSE = INTRUSION ZONE 3 2 FLASH...P AUSE = INTRUSION ZONE 2 1 FLASH...P AUSE = INTRUSION ZONE 1 SIREN CHIRP INDICA TORS *1 CHIRP = DISARM *2 CHIRPS = AR M 4 CHIRPS = ARM / [...]

128- 12 OF 12 © 2003 Audiovox Electronic Corporation, 150 Marcus Blvd., Hauppauge, N.Y. 11788 128-6802 Page 12[...]