Craftsman 152.22018 инструкция обслуживания

Owner ’ s Manual 8-in. Wheel 3/4 Horsepower (continuous duty) 3450 R.P .M. (no load speed) 8-in. BENCH GRINDER Model No. 152.220180 Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. Part No. OR94750 CAUTION: FOR YOUR OWN SAFETY ; Read and follow all of the Safety and Operating Instructions before Operating this Bench Grinder CU S Español [...]

2 T ABLE OF CONTENTS W ARRANTY PRODUCT SPECIFICA TIONS S ECTION P AGE W arranty ..........................................................................................................................................................................2 P roduct Specifications ..........................................................................[...]

3 SAFETY INSTRUCTIONS GENERAL SAFETY INSTRUCTIONS Operating a Bench Grinder can be dangerous if safety and common sense are ignored. The operator must be familiar with the operation of the tool. Read this manual to understand this Bench Grinder . DO NOT operate this Bench Grinder if you do not fully understand the limita- tions of this tool. DO NOT[...]

4 MINIMUM RECOMMENDED GAUGE FOR EXTENSION CORDS (A WG) 120 VOL T OPERA TION ONL Y 25’ LONG 50’ LONG 100’ LONG 150’ LONG 0 to 6 Amps 18 A WG 16 A WG 16 A WG 14 AWG 6 to 10 Amps 18 A WG 16 AWG 14 A WG 12 AWG 10 to 12 Amps 16 A WG 16 AWG 14 A WG 12 AWG 2 6. C ALIFORNIA PROPOSITION 65 SOME DUST CREA TED BY POWER SANDING, SA WING, GRINDING, DRIL[...]

5 GROUNDING INSTRUCTIONS I N THE EVENT OF A MALFUNCTION OR BREAK- DOWN , grounding provides the path of least resistance for electric current and reduces the risk of electric shock. This tool is equipped with an electric cord that h as an equipment grounding conductor and a ground- ing plug. The plug MUST be plugged into a matching electrical recep[...]

6 3. THE DIAMETER OF THE GRINDING WHEELS W ILL DECREASE WITH USE . Adjust the tool rests and spark arrestors to maintain a distance of 1/16” from the wheel. 4. DO NOT ST AND IN FRONT OF THE BENCH G RINDER WHEN ST ARTING IT . Stand to one side of the Bench Grinder and turn it “ON”. Wait at the side for one minute until the grinder comes up to [...]

7 CART ON CONTENTS UNP ACKING AND CHECKING CONTENTS (Fig. C) T his Bench Grinder will require a minimal amount of assembly . A 10mm and 13mm open end wrench is provided for mounting the T ool Rest Assemblies and the Spark Arrestor Assemblies. Remove all of the parts from the shipping box and lay them on a clean work surface. Compare the items to Fi[...]

8 KNOW YOUR BENCH GRINDER 1. WHEEL GUARD - Covers the grinding wheels and protects against accidental contact. 2. WHEEL COVER - Covers the grinding wheels and provides access for routine maintenance. 3. MOTOR HOUSING - Contains the electrical motor . 4. EYESHIELD MOUNTS - Supports the eyeshields. 5. EYESHIELDS - Protective Lexan see-thru shields to[...]

9 ASSEMBL Y INSTRUCTIONS A 10mm and 13mm open-end wrench (included) is required for assembly of the T ool Rest Assemblies and the Spark Arrestor Assemblies. • DO NOT assemble the Bench Grinder until you are sure the tool IS NOT plugged in. • DO NOT assemble the Bench Grinder until you are sure the power switch is in the “OFF” position. • [...]

10 WORK LIGHT (Fig. H) The Bench Grinder is provided with a Flexible Work Light to assist in visibility of the workpiece. The Bench Grinder is NOT provided with a light bulb for t he Flexible Work Light. T o reduce the risk of fire, use a 120V , 40 watt T ype A or smaller bulb , medium base. DO NOT use a light bulb that extends past the end of the [...]

11 OPERA TING THE BENCH GRINDER The Bench Grinder is designed for hand held grinding, s harpening, and cleaning operations. A L W A YS WEAR EYE PROTECTION! H ot sparks are produced during grinding operations. 1. The Power Switch must be in the “OFF” position. 2. Stand to the side of the Bench Grinder and plug in the power cord to the correct po[...]

12 CHANGING THE GRINDING WHEEL (Fig. K) Due to normal wear , both wheels will need to be replaced occasionally . See Fig. K. 1. T urn the power switch “OFF” and unplug the power cord from its power source 2. Rotate the eyeshields to the “UP” position for access to the tool rests. 3. Remove the three screws (A), flat washers (B), external to[...]

13 MAINTENANCE OF THE BENCH GRINDER T urn the power switch “OFF” and unplug the power cord from its power source prior to any maintenance. LUBRICA TION The Bench Grinder has sealed lubricated bearings in the motor housing that do not require any additional lubrication from the operator . CLEANING With the Bench Grinder unplugged, rotate the abr[...]

14 P ARTS K EY P ART N O. NO. DESCRIPTION QTY . 1 OR90055 M6x80mm CARRIAGE HD SCREW 1 2 OR90152 EYESHIELD 1 3 OR90059 M6mm FLA T W ASHER 1 4 OR90001 M6mm KNOB 1 5 OR90002 SP ACER 1 6 OR90488 SP ARK ARRESTOR-L.H 1 7 OR90059 M6mm FLA T W ASHER 1 8 OR90530 M6x10mm HEX HD SCREW 1 9 OR90001 M6mm KNOB 1 10 OR90059 M6mm FLA T W ASHER 1 1 1 OR90152 EYESHIE[...]

15 8-IN. PROFESSIONAL BENCH GRINDER P ARTS LIST MODEL NO. 152.220180[...]

16 P ARTS K EY P ART N O. NO. DESCRIPTION QTY . 1 OR90055 M6x80mm CARRIAGE HD SCREW 1 2 OR90152 EYESHIELD 1 3 OR90059 M6mm FLA T W ASHER 1 4 OR90001 M6mm KNOB 1 5 OR90002 SP ACER 1 6 OR90488 SP ARK ARRESTOR-L.H 1 7 OR90059 M6mm FLA T W ASHER 1 8 OR90333 M6x12mm HEX HD SCREW 1 9 OR90001 M6mm KNOB 1 10 OR90059 M6mm FLA T W ASHER 1 1 1 OR90152 EYESHIE[...]

17 10-IN. PROFESSIONAL BENCH GRINDER P ARTS LIST MODEL NO. 152.220600[...]

18[...]

® Registered Trademark / TM Tr ademark / SM Service Mark of Sear s Brands, L LC ® Marca Reg ist rada / TM Marc a de Fáb rica / SM Marca de Ser v i c io de Se ars Brands, LLC MC Ma rque de c ommerc e / MD Marque dépo s é e de Sear s Brands, LLC © Sears Bra nds, LLC Get i t f i xed, at your home or ours! Your Home For repair – i n y our home [...]