Crestron electronic MPS-250 инструкция обслуживания

Crestron MPS-250 Multimedia Presentation System 250 Operations Guide[...]

This document was prepared an d written by the Tech nical Documentation dep artment at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON Important Safety Instructions • Read these instructions. • Keep these instr uctions. • Heed all warnings. • Follow all instructions. • Do not use this apparatus near water. ?[...]

Crestron MPS-250 Multimedia Presentation System 250 Operations Guide – DOC. 6647A Contents • i Contents Multimedia Presentation System 250: MPS-250 1 Introduction ............................................................................................................................... 1 Features and F unctions .............................[...]

[...]

Crestron MPS-250 Multimedia Presentation System 250 Multimedia Presentation System 250: MPS-250 Multimedia Presentation System 250: MPS-250 Introduction Introduction The MPS-250 is a complete presentation control and sign al routing solution for boardrooms and classrooms. Integrating the control system, multimedia matrix switcher, m ic mixer, audi [...]

Multimedia Presentation System 250 Crestron MPS-250 System Switcher Right out of the box , the MPS-2 50 provides high-perf ormance s witching of two video and t hree RGB c omputer sources t o a single pr ojector or plasm a display. Composite , S-video, com ponent and R GBHV signals ca n be route d to the appropriate i nputs on t he display devi ce,[...]

Crestron MPS-250 Multimedia Presentation System 250 Professional Audio Features Five stereo aud io inputs o n the rear panel accept balance d or unbalance d line-level signals from computers and othe r program audio sources. Addi tional audio s ources can be brought in th rough the QM input. To accomm odate a wide range of signals, adjustable input[...]

Multimedia Presentation System 250 Crestron MPS-250 custom touchpanel based system with multiple controlled sources and display devices, can be programmed easily using Crestron SystemBuilder™ software. And, the MPS-250 works with Crestron's RoomView ® Help Desk soft ware, the industry' s most comprehensive facility-wide asset managemen[...]

Crestron MPS-250 Multimedia Presentation System 250 Internal Block Diagram The following diagrams represent the video and aud io switching abilities of the MPS-250. Video Block Diagram of the MPS-250 Composite VIDEO INPUTS 2X2 QM Matrix S-Video RGBHV Analog Video to QM QM INPUT VIDEO OUTPUTS Vid/S-Vid/Component RGBHV Vid/S-Vid/Component RGBHV RGBHV[...]

Multimedia Presentation System 250 Crestron MPS-250 Audio Block Diagram of the MPS-250 AUDIO INPUTS QM OUT 5 (Touchpanel) AUDIO OUTPUTS 6 QM Audio Combiner QM IN A/D A/D Local Mic Local Mic 1 2 Vol/EQ 6 Channel Stereo Mixer L R Vol/EQ D/A Mute D/A D/A Mute Speech Program L Program R With Phantom Power With Phantom Power Vol/EQ Mic 1&2 Program/M[...]

Crestron MPS-250 Multimedia Presentation System 250 MPS-250 Specifications (Continued) SPECIFICATION DETAILS Video/RGB Switcher Signal Types Video/HDTV Formats RGB Formats Maximum Resolution Blanking Time Sync Rise/Fall Time Sync Latency Gain QM Cable Compensation 6x5 crosspoint matrix includin g 1 x1 QM signal routing, local QM delay ske w compens[...]

Multimedia Presentation System 250 Crestron MPS-250 MPS-250 Specifications (Continued) SPECIFICATION DETAILS Audio (continued) Limiter Curve Limiter Threshold Level Limiter Attack Time Limiter Release T ime Microphone EQ Filter Gain Mic EQ Filter Center Frequencies Bass Gain Range Treble Gain Range Output Equalization PEQ Filter Gain PEQ Filter Ban[...]

Crestron MPS-250 Multimedia Presentation System 250 MPS-250 Specifications (Continued) SPECIFICATION DETAILS LCD Display Green LCD alphanumeric, adj ustabl e backlight. Two lines x 20 char acters per li ne. Displays input/outputs by name, volume level bargraph, setup menus, time/date, and other system information Power Requirements Main Power Avail[...]

Multimedia Presentation System 250 Crestron MPS-250 MPS-250 Specifications (Continued) SPECIFICATION DETAILS Available Accessories: APAD C2N-DB12 C2N-FTB C2N-MNETGW CLS-C6(M) CLW-DIM1RF and CLW-SW1RF CNSP-XX CNX-B12 CNXRMIRD IRP2 QM-AMP3X80MM QM-AMP3X80SR Wall Mount LCD Controller 12-Button Decorator Keypad FlipTop Control Center infiNET™ Gateway[...]

Crestron MPS-250 Multimedia Presentation System 250 MPS-250 Overall Dimensions 12.5 8 in (31.95 cm) 3.47 in (8.81 cm) 17.0 3 in (43.24 cm) 11.85 in (30.08 cm) Operations Guide – DOC. 6647A Multimedia Presentation System 250: MPS-250 • 11[...]

Multimedia Presentation System 250 Crestron MPS-250 MPS-250 Buttons and Ports 1 2 3 4 5 6 8 9 10 11 12 14 16 17 19 20 29 18 21 23 24 22 27 25 28 30 31 33 15 26 7 13 32 12 • Multimedia Presentation System 250: MPS-250 Operations Guide – DOC. 6647A[...]

Crestron MPS-250 Multimedia Presentation System 250 Connectors, Controls & Indicators # CONNECTO RS 1 , CONTROLS & INDICATORS DESCRIPTION 1 NET LED (1) yellow LED, indicates Cresnet bus activit y. 2 MSG LED (1) yellow LED, illuminates when a message is present in the message log. T o vie w the contents of the message log, use the front pane[...]

Multimedia Presentation System 250 Crestron MPS-250 Connectors, Controls, & Indicators (Continued) # CONNECTO RS 1 , CONTROLS & INDICATORS DESCRIPTION 8 MC/LN 1 – 2 (2) 5-pin 3.5mm detacha bl e terminal blocks Comprises (2) Balanced microphon e/line inputs Balanced Mic Input Lev el: -52 to -12 dBV, 240 mV rms maximum Balanced Line Input L[...]

Crestron MPS-250 Multimedia Presentation System 250 Connectors, Controls, & Indicators (Continued) # CONNECTO RS 1 , CONTROLS & INDICATORS DESCRIPTION 12 REC OUT (1) 5-pin 3.5 mm detachable t erminal block; Balanced/unba lanc ed, stereo line-leve l output; Output Impedance: 200 ohms balanced, 100 ohms unbalanced; Maximum Output Level: 4 V r[...]

Multimedia Presentation System 250 Crestron MPS-250 Connectors, Controls, & Indicators (Continued) # CONNECTO RS 1 , CONTROLS & INDICATORS DESCRIPTION 17 IR/SERIAL OUT (4) 2-pin 3.5 mm detacha ble terminal blocks, IR/Serial output ports; IR o utput up to 1.2 MHz; One-way serial TTL/RS-23 2 (0-5 Volts) 2 up to 9600 baud 18 IR IN (1) 3-pin 3.[...]

Crestron MPS-250 Multimedia Presentation System 250 Connectors, Controls, & Indicators (Continued) # CONNECTO RS 1 , CONTROLS & INDICATORS DESCRIPTION 25 TOUCH PANEL OUT Contains one CH port an d one QM port. CH Port: 8-wire RJ-45 female; CAT 5 balanced video output port; Signal Types: Dynamic all y configurabl e for component (Y/P b /P r )[...]

Multimedia Presentation System 250 Crestron MPS-250 Connectors, Controls, & Indicators (Continued) # CONNECTO RS 1 , CONTROLS & INDICATORS DESCRIPTION 27 COM A & B (2) DB9 male, bidirectional R S-232 ports; Up to 115.2k baud, har dware and soft ware handshaking support f or communic ation with serial devices. Can also b e used for modem[...]

Crestron MPS-250 Multimedia Presentation System 250 Connectors, Controls, & Indicators (Continued) # CONNECTO RS 1 , CONTROLS & INDICATORS DESCRIPTION 29 OUTPUT 1-4 Contains composite, S-video (Y/ C), component (Y, P b , P r ) and RGBHV outputs o n six BNC connectors and on e DB15HD connector. Composite/P b Output 1: (1) BNC female, composi[...]

Multimedia Presentation System 250 Crestron MPS-250 Connectors, Controls, & Indicators (Continued) # CONNECTO RS 1 , CONTROLS & INDICATORS DESCRIPTION 33 100 – 240V ~2. 5A 50/60 Hz (POWER SUPPLY) (1) IEC Socket, mates w ith removable power cord (included). 1. Interface connectors for NET , INFRARED-SERIAL , IR IN , INPU T , RELAY OUTPUT ,[...]

Crestron MPS-250 Multimedia Presentation System 250 Industry Compliance This unit has been manufactured to comply with UL’s Standards for Safety in Canada and t he United States . Formal appr oval is pending. As of the date of manufactu re, the MPS-250 has been tested and found to c omply with specifications for CE m arking and standards per EMC [...]

Multimedia Presentation System 250 Crestron MPS-250 Setup Network Wiring When wiring the Cresnet ® and Ethernet network, consider the following: • Use Crestron Certified Wire. • Provide sufficient power to the system. CAUTION: Insufficie nt power can lead to unpre dictable results or damage to the equipment. Please use th e Crestron Power Calc[...]

Crestron MPS-250 Multimedia Presentation System 250 CresCAT-QM Cable NOTE: Do not unt wist the t wo wires in a s ingle pair fo r more than 1/3-1/2” (0.84-1.27 cm ) when m aking a connecti on. The twists are critical to canc eling out interference between t he wires. The aggregate cable length of a signal path originating at the MPS-250 and termin[...]

Multimedia Presentation System 250 Crestron MPS-250 QM Network Topology T P S-12G /15 G - Q M - L MP S - 250 QM QM QM O r ig in a tio n P oi n t s E ndp oi nts QM M i dpo in ts MP S - 250 MP S - 250 QM -M D 7 x 2 Installation Ventilation The MPS-250 should be used in a well-vent ilated area. The ve n ting holes should no t be obstructed under any c[...]

Crestron MPS-250 Multimedia Presentation System 250 2. Position a rack ear so that its mounti ng hole s align with the holes vacated by the screws in ste p 1. 3. Secure the ear to the unit with three screws from step 1, as shown in the following diagram. Ear Attachment for Rack Mounting (this image shows a 1RU device) 4. Repeat procedure (steps 1 t[...]

Multimedia Presentation System 250 Crestron MPS-250 Hardware Connections for the MPS-250, Front Hardware Connections for the MPS-250, Rear When runni ng the out- of-the-bo x program , the MPS-25 0 can supp ort the foll owing Crestron devices: • (2) APAD • (2) C2N-FTB • (2) CNX-B12 • (2) C2N-DB 12 • (2) CLW-DIM1RF / CL W-DIMS1RF (re quires[...]

Crestron MPS-250 Multimedia Presentation System 250 CAUTION: Al l source devi ces should be grounded t o the MPS- 250. NOTE: The MPS-25 0 can only be powered by the included p ower cord. Po wer cannot be supp lied from network de vices that are c onnected to the m ini-term inal block connect ors. NOTE: For Cresnet, CAT5, and Quick Media connections[...]

Multimedia Presentation System 250 Crestron MPS-250 Typical Balanced/Unbalanced Ou tputs Shield AMP Left Right + - G + - Balanced Ou tput + + AMP Left Right + - G + - Unbalanced Output + + Configure the RGB Input Ports Each of the RGB input port s feature a set of six DIP switches located ins ide the MPS-250. The se switches are used to set the syn[...]

Crestron MPS-250 Multimedia Presentation System 250 DIP Switch Location DIP SWITCHES LOCATED UNDER ACCESS PANEL Set the DIP Switches 1. Referring to the following table, set the DIP switches of each RGB input port to the required sync input impedance and DDC functionality. DIP Switch Function Chart DDC HORIZONTAL SYNC VERTICAL SYNC SWITCH 1 2 3 4 5[...]

Multimedia Presentation System 250 Crestron MPS-250 Label the Buttons Use Crestr on Engraver software to p rint custom labels for t he MPS-25 0’s front pa nel buttons and L EDS. Crestr on recomm ends printi ng on 100-p ound paper. Paper weighing less than 100 pounds will tend to crumple while slid ing in, while paper weighing more than 100 pounds[...]

Crestron MPS-250 Multimedia Presentation System 250 Programming Software Have a questi on or comment about Crestr on software? Answers to f requently asked quest ions (FAQs) can be viewed in the Onl ine Help section of the Crestro n website. To post a questio n or view questions you have submitted to Crestron’s True Blue Support, log in at http:/[...]

Multimedia Presentation System 250 Crestron MPS-250 Configuration Manager Configuration Manager i s the view where program mers “build” a C restron cont rol system by selecting hard ware from t he Device Library . • To incorporate the MPS-250 into the system , drag the MPS-250 fr om the Control Systems folder of the Device Library and drop it[...]

Crestron MPS-250 Multimedia Presentation System 250 of-the-box functionality program or “custom” for settin gs made when running a custom prog ram) and System Configuratio n.txt files from the NVR AM Disk directory. After the new out-of-the-box functionality program or custom program has been loaded, use Windows Explorer an d Cr estron Toolbox [...]

Multimedia Presentation System 250 Crestron MPS-250 Uploading and Upgrading Crestron recommends using the latest pr ogramming software and that each device contains the latest firmware to take advantage of the most recently released features. However, before attem pting to upl oad or upgrade it is necessary to establish communicat ion. Once communi[...]

Crestron MPS-250 Multimedia Presentation System 250 TCP/IP Ethernet Communication ETHERNET PC RUNNING CRESTRO N TOOLBOX MPS-250 • Establish USB com munication bet ween MPS-250 an d PC. • Enter the IP ad dress, IP mask and de fault router of the MPS-250 via the Crestron Toolbo x ( Functions | Ethernet Addressing ); otherwi se enable DHCP. • Co[...]

Multimedia Presentation System 250 Crestron MPS-250 Configuration & Operation The MPS-250 can be used f or audio a nd video s witching without any programm ing required. This i s ideal for t hose that need a basic audio- video s witching syst em. Prior to operation, the MPS-25 0 must be configured for use. Configuration The MPS-250 is configure[...]

Crestron MPS-250 Multimedia Presentation System 250 Exit the Menu To exit the menu: • While in the main menu, press th e MENU button to exit the menu. Exit Menu Prompt Exit Setup Menu? Yes No ⇒ Press the soft button labeled Yes to exit the menu or press the soft button labe led No to return to the menu. NOTE: The following sections d escribe co[...]

Multimedia Presentation System 250 Crestron MPS-250 The menu is separated int o four section s. • Audio Setup: Contains co ntrols for PROGRAM , SPEECH , and RECORD out put settings, source in put compensat ion, mast er startup volume, and m icrophones. • Video Setup: Contains controls fo r naming i nput sources, sel ecting input signal types ( [...]

Crestron MPS-250 Multimedia Presentation System 250 • Press the k or j buttons until “Source Mix” is displayed on the LCD and press ENTER to ope n the Program Source Mix contr ols. Program Source Mix Controls Program Source Mix Aud. Only • Press the k or j buttons until the desired setting is displayed on the LCD. The current setting is ind[...]

Multimedia Presentation System 250 Crestron MPS-250 NOTE: While adjusting the Program Bass level, the Program Volume level can be adjusted by turning the volume control clockwise to raise the volume, or counterclockwise to lower the vo lume. When adjusting the volume, the display will change to indicate th e volume level. • Press MENU or ENTER to[...]

Crestron MPS-250 Multimedia Presentation System 250 Program Minimum Volume Control Prog. Min Volume 30% • Adjust the Program Minimum Volume level with the j and k button s. Press the k button to increase the Program Minimum Volume level. Press the j button to lower the Program Minimum Volume level. The highest Program Minimum Volume setting is 30[...]

Multimedia Presentation System 250 Crestron MPS-250 NOTE: While adjusting the Program Maximum Volume level, the Program Volume level can be adjust ed by turning t he volu me control clockwise to raise the volum e, or co unterclockwise to lower the volume. When adjusting the vo lume, the display will change to indicate the volume level. • Press ME[...]

Crestron MPS-250 Multimedia Presentation System 250 Program Startup Volume Control Prog. St ar tup Vol . 30% • Adjust the Program Startup Volume level with the j and k buttons. Press the k button to increase the startup volu me level. Press the j butt on to lower the startup volume level. The highest Program Startup Volume setting is 100%. NOTE: [...]

Multimedia Presentation System 250 Crestron MPS-250 Speech Source Mix Controls Speech Source Mix Aud. Only • Press the k or j buttons until the desired setting is displayed on the LCD. The current setting is indicated with an asterisk (*). The following settings are available: ⇒ Aud. Only : Sends the audio signal from the selected source to th [...]

Crestron MPS-250 Multimedia Presentation System 250 NOTE: While adjusting the Speech Bass level, th e Speech Volume level can be adjusted by turn ing the volume control clockwise to raise th e volume, or counterclockwise to lower the vo lume. When adjusting the volume, the display will change to indicate th e volume level. • Press MENU or ENTER t[...]

Multimedia Presentation System 250 Crestron MPS-250 • Adjust the Speech Delay with the j and k buttons. Press the k but ton to increase the delay. Press the j button to lower th e delay. The highest delay setting is 40 milliseconds. NOTE: While adjusting the Speec h Dela y, the Speech Volume level can be adjusted by turning the volume control clo[...]

Crestron MPS-250 Multimedia Presentation System 250 The MPS-250 ships with the Volume Control Mode set to the Master Vol. setting. When switching the Volume Con trol Mode from the Master Vol. setting to either the Program Only setting, the Speech Only setting, or the user selectable Pgm/Spch Sel. setting, the Minimum and Maximum Volume levels for t[...]

Multimedia Presentation System 250 Crestron MPS-250 Speech Minimu m Volume Contro l Spch. Min Vol ume 30% • Adjust the Speech Min imum Volume level with the j and k butt ons. Press the k button to increase the Speech Minimum Volume level. Press the j button to lower the Speech Minim um Volume level. The highest Speech Minim um Volum e setting is [...]

Crestron MPS-250 Multimedia Presentation System 250 • Press MENU or ENTER to save ch anges an d return to th e previo us scr een. Adjust the Speech Startup Volume The Speech Startup Volume co ntrol is used to establish the SPEECH output ’s volume level setting when an input is selected. The RECORD and PROGRAM outputs are not affecte d by change[...]

Multimedia Presentation System 250 Crestron MPS-250 • Adjust the Record Volume level by turning the volume control clockwise to raise the volume, or counterclockwise to lower the volume. When adjusting the Record Volume level, the display will change to indicate the volume level. NOTE: The Record Volume can only be us ed if the Fixe d/Variable Mo[...]

Crestron MPS-250 Multimedia Presentation System 250 Fixed/Variable Control Rec. Fixed/Variable Fixed • Press the k or j buttons until the desired setting is displayed on the LCD. The current setting is indicated with an asterisk (*). The following settings are available: ⇒ Fixed : The RECORD output ope rates at a fi xed level. ⇒ Variable : Th[...]

Multimedia Presentation System 250 Crestron MPS-250 • Press MENU or ENTER to save ch anges an d return to th e previo us scr een. Input Compensation The compensat ion level of eac h input can be set from the M PS-250’s front panel. The line outputs are not affected by changes made to the inp ut compensation level. Set the Compensation Level To [...]

Crestron MPS-250 Multimedia Presentation System 250 • Press MENU or ENTER to save changes an d return to the Select Input to Compensate controls. • Repeat for each input to be adjusted. • Press MENU t o save changes and return to t he Audio Setu p menu. Master Startup Volume Control The Master Startup Volume control is used to establish the v[...]

Multimedia Presentation System 250 Crestron MPS-250 Switch Microphone Gating Microphone gat ing can be i ndividually set on each m icrophone i nput. To swit ch microphone ga ting on or of f: • Access the Micro phone menu as desc ribed on page 53. • Press the k or j buttons until “Mic 1 Gating” or “Mic 2 Gating” is displayed on the LCD a[...]

Crestron MPS-250 Multimedia Presentation System 250 ⇒ ON : The compression function for the selected microphone input is enabled. • To exit the Microphone Compression co ntrol without saving changes, press MENU . Switch Microphone Lim iter A microphone limit er can be indi vidually set o n each microph one input. To s witch the microphone limit[...]

Multimedia Presentation System 250 Crestron MPS-250 • Press the k or j buttons until the desired setting is displayed on the LCD and press ENTER to save the setting. The current setting is indicated with an asterisk (*). The following settings are availab le: ⇒ OFF : Phant om power t o the mi crophone in puts is disa bled. ⇒ ON : Phantom powe[...]

Crestron MPS-250 Multimedia Presentation System 250 Select Input to Name Sel. Input To Name 1:BNC 1 • Press the k or j buttons until the input to be named is displayed on the LCD and press ENTER . The cursor is placed a fter the last character in the input name. Name the Input BNC 1_ DEL INS < > • Turn the vol ume control clo ckwise or co[...]

Multimedia Presentation System 250 Crestron MPS-250 Select Input Type Menu Sel. Input Type 1:BNC 1 • Press the k or j buttons to select the video input to be configured and press ENTER . The current setting is indicated with an asterisk (*). • Press the k or j buttons until the desired input type is displayed. Select Input Type Select Input 1 T[...]

Crestron MPS-250 Multimedia Presentation System 250 • Press the k or j buttons until the output to be named is displayed on the LCD and press ENTER . The cursor is placed a fter the last character in the output nam e. Name the Output Output 1_ DEL INS < > • Turn the vol ume control clo ckwise or counterclockwise (or press the k or j butto[...]

Multimedia Presentation System 250 Crestron MPS-250 Display the IP Address IP Address [000] 000. 000. 000 • Turn the vol ume control clo ckwise or counterclockwise t o select a number in the left-most section of the IP address. You can also press the k or j buttons to select a number. • Press ENTER to move the cursor to the ne xt section of the[...]

Crestron MPS-250 Multimedia Presentation System 250 Set the Default Router The MPS-250 can be configured to use a De fault Router f or TCP/IP communications. To set the IP address of the Default Router: • Access the Network Set up menu as described on page 59. • Press the k or j buttons until “Def. Router” is displayed on the LCD and press [...]

Multimedia Presentation System 250 Crestron MPS-250 • To save the setting and return to the Network Setup menu, press ENTER . To cancel the operation and re turn to the Network Setup menu, press MENU . Set the WINS Mode The MPS-250 can use a WINS server to obta in an IP a ddress. To set the WI NS mode: • Access the Network Set up menu as descri[...]

Crestron MPS-250 Multimedia Presentation System 250 Change the Hostname • Turn the vol ume control clo ckwise or counterclockwise (or press the k or j buttons) to select a new letter (upper case or lowercase) or number. M ove the cursor by pressing the soft buttons labeled < or > . The Host name can be up to 64 characters in leng th. To del[...]

Multimedia Presentation System 250 Crestron MPS-250 Change the Domain Name corporate.company.c DEL INS < > • Turn the vol ume control clo ckwise or counterclockwise (or press the k or j buttons) to select a new letter (upper case or lowercase) or number. M ove the cursor by pressing the soft buttons labeled < or > . T he Do main na me[...]

Crestron MPS-250 Multimedia Presentation System 250 • Press the k or j buttons until “MAC Address” is displayed on the LCD and press ENTER to display the MAC address. • Press MENU to return to the Network Setup menu. Control Setup Basic control s ystem operations can be perform ed from the M PS-250 front panel using the Co ntrol Setu p menu[...]

Multimedia Presentation System 250 Crestron MPS-250 Select Function to Name Select Fct. To Name 1:MUTE • Press the k or j buttons until the function to be named is displayed on the LCD and press ENTER . The cursor is placed a fter the last character in the function nam e. Name the Function MUTE_ DEL INS < > • Turn the vol ume control clo [...]

Crestron MPS-250 Multimedia Presentation System 250 ID Devices Prompt Press ENTER to ID all devices. • Press ENTER to continue the identification pro cess, the MPS-250 will clear all device set tings and pr ompt the use r to select the de vice type to be identified. Select Devi ce Type Select device type APAD • Press the k or j buttons until th[...]

Multimedia Presentation System 250 Crestron MPS-250 Display the APAD Upgrade Controls Upgrade APAD Yes • To upgra de the APAD , press th e k or j buttons until “Yes” is displayed on the LCD an d press ENTER . The MPS-250 will upgrade the APAD’s firmware (if necessary ) and copy t he required files to the A PAD. • To cancel the upgrade pr [...]

Crestron MPS-250 Multimedia Presentation System 250 • Press the k or j buttons until “Info” is displayed on the LCD and press ENTER to display the Info men u. Display the Info Menu Info REMS HW NET OPS • To view program information, press the soft button lab eled REMS . Display the Program Information Program Boot Directo << >> [...]

Multimedia Presentation System 250 Crestron MPS-250 Display Connected Network D evices 2E: APAD LCD 6-bu << >> ⇒ Press the k or j buttons to s ee other netw ork devices. If the information for a network device is pa rtially displayed, press the soft buttons labeled << or >> to view the rest of the information. ⇒ Press th[...]

Crestron MPS-250 Multimedia Presentation System 250 Display the Message Controls System log: Top Clear << >> • To scroll through messages in th e log, press the k or j but tons. • To jump to the beginning of th e log, press the soft button labeled Top . • To jump to the last message in the long, press th e soft button labeled Btm [...]

Multimedia Presentation System 250 Crestron MPS-250 Display the Date Controls DATE: 10/16/2006 MO DAY YR ⇒ To set the month, press the soft button lab eled MO . To set the day, press the soft button lab eled DAY . To set the year, press the soft button labeled YR . A pair of brackets will appear around the selected part of the date. ⇒ Press the[...]

Crestron MPS-250 Multimedia Presentation System 250 Restore Default Settings The MPS-25 0 can be restored to its d efau lt factory settings from the fron t panel. Users can select to restore the audio settings or to restore th e audio settings, source names, out put names, and function names. • To restore audio settings only: ⇒ Access the Co nt[...]

Multimedia Presentation System 250 Crestron MPS-250 Restore Defaults Menu-All Settings Restore Defaults All settings ⇒ Press the k or j buttons until “All setting s” is displayed on the LCD and press ENTER . Confirm Restore All Default Settings Only Reset all settings? No ⇒ Press the k or j buttons until “Yes” is displayed on the LCD an[...]

Crestron MPS-250 Multimedia Presentation System 250 Front Panel Lock Controls Front Panel Lock: On • Press the k or j buttons to toggle between On and Off. The current setting is indicated with an asterisk (*). • Press ENTER to save the new setting and retu rn to the Control Setup menu. Operation Using the out-of-the-box functio nality, the MPS[...]

Multimedia Presentation System 250 Crestron MPS-250 Raise the Projection Screen Press the button labeled SCREEN UP to raise the projector screen. NOTE: This function will only work if a projection screen’s control lines have been connected to RELAY 1 (up cont rol) and RELAY 2 (do wn control) . Adjust the Volume Level Th e volume control of the MP[...]

Crestron MPS-250 Multimedia Presentation System 250 Adjust Lighting To set lighting to one of two preset lighting values, press either LIGHTS PRE 1 or LIGHTS PRE 2 . NOTE: This function will only work if a CLS-C6, infiNET switch, or infiNET dimmer was previously identified and connected to the MPS-250 . The CLS-C6 can be identified as a Cresnet dev[...]

Multimedia Presentation System 250 Crestron MPS-250 3. Press the soft button labeled Select to route the source to the projector and touchpanel output. Turn Off the System To turn off the system: 1. Press the Power button. 2. Press the soft button labeled Sys. Off . 3. Press the soft button labeled Yes to confirm. The display will indicate that the[...]

Crestron MPS-250 Multimedia Presentation System 250 NOTE: This function will only work if a CLS-C6, infiNET switch, or infiNET dimmer was previously identified and connected to the MPS-250 . The CLS-C6 can be identified as a Cresnet devi ce in the MPS -250 setu p screens as de scribed on page 66. Crestro n’s infiNET s witches and di mmers require[...]

Multimedia Presentation System 250 Crestron MPS-250 When switching sour ces from the keypad, the MPS-250 will route th e signal to the projector out put and then route the si gnal to the t ouchpanel output. Turn On the System To turn on the system, press any of the so urce buttons on the button p ad. The selected source will be rout ed to all of th[...]

Crestron MPS-250 Multimedia Presentation System 250 Turn On the System To turn on the system, press any of the source buttons on the control center. The selected source will be rout ed to all of the outpu ts. NOTE: Typically, signal routing information is not d isplayed on the front panel of the MPS-250. However, if an outpu t button on the MPS-250[...]

Multimedia Presentation System 250 Crestron MPS-250 Problem Solving Troubleshooting The following table provides corrective action for possible trouble situ ations. If further assistance is required, please contact a Crestron custom er service representative. MPS-250 Troubleshooting TROUBLE POSSIBLE CAUSE(S) CORRECTIVE ACTION Unexpected response fr[...]

Crestron MPS-250 Multimedia Presentation System 250 MPS-250 Troubleshooting (Continued) TROUBLE POSSIBLE CAUSE(S) CORRECTIVE ACTION Poor picture quality (Video). Cables improperl y connected. Verify that all cabl es are secure. NOTE: If com munication ca nnot be esta blished or the control system is locked-u p, refer to “Troubleshooting Commun ic[...]

Multimedia Presentation System 250 Crestron MPS-250 8. In the “Address Book” window, click the Add Entry b utton and give the new entry a name (e.g. “System Monitor”). 9. Click the arrow next to the Device Type drop down list. A “Warning” window will open to inform you that this is an advanced feature. Click OK , then select “2-Series[...]

Crestron MPS-250 Multimedia Presentation System 250 Check Network Wiring Use the Right Wire In order to ensure optimum performance over the full ran ge of your installation topology, Crestron Certified W ire and onl y Crestron Certified Wire may be u sed. Failure to do so may incur additional ch arges if support is required to identify performance [...]

Multimedia Presentation System 250 Crestron MPS-250 Reference Documents The latest version of all documents mentioned with in the guide can be obtained from the Crestron website ( www.crestron.c om/manual s ). This link will provide a list of product m anuals arran ged in alpha betical order by model n umber. List of Related Reference Documents DOC[...]

Crestron MPS-250 Multimedia Presentation System 250 Software License Agreement This License Agreement (“Agree ment”) is a legal contract betw een you (either an individual or a single business entity) and Crestron Electronics, Inc. (“Crestron”) for so ftware referenced in this guide, which in cludes computer software and as applicab le, ass[...]

Multimedia Presentation System 250 Crestron MPS-250 If You are a business or organization, You agree that upon request from Crestron or its authorized agent, You will within thirty (30) days fully document and certify that use of any and all Software at the time of the request is in conformity with Your valid licenses from Cres tron of its authoriz[...]

Crestron MPS-250 Multimedia Presentation System 250 Return and Warranty Policies Merchandise Returns / Repair Service 1. No merchandise m ay be returned for credit, ex change or service witho ut prior authorization from CR ESTRON. To obtai n warranty serv ice for CREST RON products, contact an authorized CRESTRON deal er. Only authorized CRESTRON d[...]

Crestron Electronics, Inc. Operations Guide – DOC. 6647A 15 Volvo Drive Rockleigh, NJ 07647 (201992 6) Tel: 888.CREST RON 06.08 Fax: 201.76 7.7576 Specific at ions subject to www.crestron.com change without notice.[...]