CrimeStopper RS700 IIIER инструкция обслуживания

RS700 IIIER/RS701 III SERIES I II REMOTE ENGINE STARTING SYSTEM INSTALLATION INSTRUCTIONS This Remote Start Module provides the following features: SELECTABLE ENGINE SPEED SENSING: TWO PROGRAMMABLE MULTI - • Tach, Semi - Tachless, & Vacuum FU NCTION OUTPUTS FOR: • OEM Alarm Disarm TACH AMPLIFIER: • Throttle Pulse for Carbureted vehicles ?[...]

INSTALLATION CONSIDERATIONS / WARNINGS To ease and reduce installation time, we suggest you consider the following points before starting. 1. Determine most suitable locations for all components to be placed. These components include: the module itself, o verride / programming switches, and possible relays. 2. Use a Volt - Ohm meter to test and loc[...]

PIN 2: ORANGE: MULTI - FUNCTION OUTPUT 2 Output 2 comes pre - programmed to operate as the Anti - Grind/Start er Disable output. It can also be used for the sensor disable circuit for a host alarm. This output activates whenever a remote start is requested, and when the vehicle is remotely locked with the transmitter. Connect this w ire to terminal[...]

PIN 5: GREEN: ( - ) START ACTIVATION TRIGGER This wire allows a h ost alarm ( - ) Negative Auxiliary Channel Output to activate a Remote Start or it can be connected to a Negative wire of a factory keyless entry system. If the Factory Keyless Entry System wire can produce a Negative output for 1 second or 3 short pulses w ithin 5 seconds, that syst[...]

TACH LEARING MODE The TACH LEARNING MODE is the most reliable and consistent method of engine speed sensing. This wire looks for the pulsing signal that is created to monitor the engine speed or fire the coil. Most modern ignition syst ems utilize a crankshaft sensor to monitor the engine speed. There are 4 different types of signals that may provi[...]

TACH WIRE TROUBLESHOOTING If all remote start wiring has been completed, attempt a remote start. If engine starts, and starter disengages quickly, and engine continues to run, the tach wire has been properly connected. ** If system does not remote start properly, you will have to locate a different tach wire and reprogram. AN INADEQUATE TACH SOURCE[...]

SEMI - TACHLESS MODE This new feature provides an easy method of starting the vehicle without locating the exact tach wire required. It uses a timed crank output combined with the tach wire as a crude pulse monitor. This combination prevents the starter from engaging into an already running engine and provides a reliable meth od of detecting when r[...]

IGNITION S WITCH WIRING 6 PIN HIGH - CURRENT SPADE CONN ECTORS: PIN 1: RED 14Ga.: BATTERY CONSTANT FUSED 30A PIN 2: BROWN 14Ga.: STARTER OUTPUT - 30A PIN 3: GRAY 14Ga.: IGNITION 2 - 30A PIN 4: WHITE 18Ga.: + PARKING LIGHTS 10A SEE NEXT PAGE PIN 5: PINK 14Ga.: IGNITION 1 - 30A PIN 6: RED 14Ga.: BATTERY CONSTAN T FUSED - 30A See diagram below for con[...]

PO WER DOOR LOCK WIRING 3 PIN DOOR LOCK PLUG: PIN 1: GREEN: Sends a ( - ) Negative pulse for LOCK; Sends a positive pulse for UNLOCK PIN 2: RED : +12V Coil Power for external relays TERM 86. (If needed.) PIN 3: BLUE: Sends a ( - ) Negative pulse for UNLOCK; Sends a positive pulse for LOCK DETERMINING DOOR LOCK TYPE: There are several types of door [...]

TESTING FOR REVERSE POLARITY DOOR LOCKS WITH A VOM ( 5 - wire switch) Reverse Polarity Door Lock Systems are a seri es circuit in which one switch serves as a "master" source for the motor grounds. When any switch in the circuit is pressed, one of the grounds is "lifted" and voltage is applied to the open circuit causing the loc[...]

PO WER DOOR L OCK WIRING DIAGRAMS AFTERMARKET MOTOR/DOOR LOCK WIRING REVERSE POLARITY DOOR LOCK WIRING GREEN GREEN FUSED FUSED RED RED +12V +12V BLUE BLUE + + 86 85 86 85 86 85 86 85 87 87 87 87 30 87A 30 87A 30 87A 30 87A + L CUT UL CUT ONE WIRE / DUAL VOLTAGE SYSTEM GROUND/OPEN LOCKING SYSTEM GREEN GREEN RED RED BLUE BLUE + 86 85 86 85 86 85 FUSE[...]

PROGRAMMING CODE LEARNING PROGRAMMING: The RS700 IIIER will learn up to 4 different transmitter security codes. This procedure does not apply to the RS701 III add - on Remote Start module. Transmitter Programming: 1) Open Hood ( Gray wi re grounded). 2) Depress and Hold BRAKE PEDAL, and then Press Program Button until parking lights turn ON solid. [...]

PROGRAMMING Options Programming: 1) Open Hood (Gray wire grounded) Dep ress and Hold BRAKE PEDAL. 2) Press and Release program button. (Parking lights come on.) 3) Wait 2 seconds, then press and release brake pedal again. 4) Release BRAKE PEDAL 5) Momentarily Press then Release program button the number of times for the option program le vel desire[...]

+[...]