Cub Cadet 7264 инструкция обслуживания

CUB CADET LLC P.O. BOX 361131 CLEVELAND, OHIO 44136-0019 [www.cubcadet.co m] IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY Warning : This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-covered, brush-covered or grass-covered land unless the engine’s exhaust system is equipped [...]

2 TABLE OF CONTENTS TO THE OWNER .................................................................................................................... 2 CALLING SERVICE INFORMATION ...................................................................................... 2 RECORDING MODEL AND SERIAL NUMBER INFORMATION ...................................[...]

3 www.cubcadet.com CUB CADET LLC P. O. BOX 361131 CLEVELAND, OH 44136 DEALER LOCATOR PHONE NUMBER: 877-282-8684 Model Number Mfg. Date XXXXXXXXXXX XXXXXXXXXX RECORDING MODEL AND SERIAL NUMBER INFORMATION Product identification plates are provided for major components of your tractor. The numbers on these plates are important if your tractor should [...]

4 IMPORTANT SAFE OPERATION PRACTICES WARNING: THIS SYMBOL POINTS OUT IMPORTANT SAFETY INSTRUCTIONS WHICH, IF NOT FOLLOWED, COULD ENDANGER THE PERSONAL SAFETY AND/OR PROPERTY OF YOURSELF AND OTHERS. READ AND FOLLOW ALL INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE YOUR UNIT. FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL[...]

5 • Maintain the weight balance of the tractor. Install front end weights to counterbalance heavy implements attached to the three point hitch. Do not operate the tractor with a light front end. • Any towed vehicle with a total weight exceeding that of the tractor should be equipped its own braking system that is operational from the tractor se[...]

6 • To prevent injury, do not adjust, unclog, clean, or service PTO driven equipment while the tractor engine is running. • Make certain all PTO shields are always installed. 5. SAFETY FRAME (ROPS) Your tractor is equipped with a rollover protective structure (ROPS) which must be maintained in a fully functional condition. Use care when driving[...]

7 SAFETY LABELS STARTING INSTRUCTIONS 1. KNOW THE OPERATING AND SAFETY INSTRUCTIONS IN THE OPERATORS'S MANUAL AND ON THE TRACTOR . 2. MOVE THROTTLE TO MID POSITION AND DEPRESS BRAKE PEDAL. 3. TURN KEY TO THE START POSITION. 1. DISENGAGE PTO AND SET PARKING BRAKE. 2. MOVE THROTTLE CONTROL TO MID POSITION AND TURN KEY OFF. • GO UP AND DOWN SLO[...]

8 SAFETY LABELS (Cont.) WARNING FAILURE TO FOLLOW ANY OF THE INSTRUCTIONS ABOVE CAN CAUSE SERIOUS INJURY TO THE OPERATOR, OR OTHER PERSONS. To avoid personal injury, keep PTO shield in place. Disengage PTO and stop engine before servicing tractor, or implements, or attaching or detaching implements. Pull only from draw bar. pulling from any other p[...]

9 SECTION 1: CONTROLS AND FEATURES FLOORBOARD AND DASH PANEL MOUNTED CONTROLS Figure 1 B C D E F G H J K L M A A B C D E F G H J K L M Steering Wheel PTO Switch Throttle Handle Ignitio n Switch Brake Pedal Forward/Reverse Pedal Seat Adjustment Lever Differential Lock Pedal Parking Brake Lever Hazard Light Switch Headlight Switch Instrument Panel * [...]

10 NOTE: References to LEFT and RIGHT indicate that side of the tractor when facing forward while seated in the drivers seat. Reference to FRONT indicates the grille end of the tractor; to REAR, the drawbar end. A. Steering Wheel The steering wheel is centered on the dash panel. It is used to change the direction (left or right) of the tractor whil[...]

11 H. Differential Lock Pedal Figure 6 Located at the rear of the left floor board, the differential lock pedal engages the transmission differential lock. The differential lock is used to gain additional trac- tion when operating the tractor on wet or loose soil. When the pedal is depressed the rear wheels of the tractor are prevented from rotatin[...]

12 M. Instrument Panel Figure 10 1. Fuel Gauge The fuel gauge, located on the left side of the instrument panel, monitors the fuel level in the fuel tank. The needle pointing to the right indicates a full tank. The ignition switch must be in the ON position to read the fuel gauge. 2. Tachometer The tachometer, located on the right side of the instr[...]

13 FENDER MOUNTED CONRTOLS AND FEATURES Figure 11 A B N D E F G H K J H J K L G C M A. Fuel Fill Cap The fuel fill cap is located on the left fender beside the operator’s seat. WARNING: Never fill the fuel tank to the top of the filler neck. Expansion could result in overflow, allowing highly flammable fuel to come in contact with the operator. B[...]

14 E. Transmission Hi/Lo Range Shift Lever The Hi/Lo range shift lever is located on the right fender. The lever has two speed range settings and a neutral position. The lever must be shifted into either the high or low range prior to depressing the forward/reverse pedal to drive the tractor. • Push the lever forward to shift into the high range.[...]

15 SECTION 2: OPERATION ROLLOVER PROTECTIVE STRUCTURE (ROPS) This tractor is equipped with a foldable Rollover Protection Structure (ROPS) and seat belts. When used together they are effective in reducing injuries to the operator in the event of an accidental tractor rollover. The safety provided by the ROPS is minimized if the seat belt is not pro[...]

16 SAFETY INTERLOCK SYSTEM This tractor is equipped with a safety interlock system for the protection of the operator. If the interlock system should ever malfunction, do not operate the tractor. Contact your authorized Cub Cadet Dealer. The safety interlock system prevents the engine from cranking or starting unless the brake pedal is fully depres[...]

17 STARTING THE ENGINE WARNING: Always sit in the operator’s seat when starting the tractor, Never attempt to start the engine while standing beside the tractor. WARNING: Never use starting fluids, such as ether, as a starting aid. Severe engine damage or fire could result. • Operator must be sitting in the tractor seat. • Move the throttle h[...]

18 DRIVING THE TRACTOR WARNING: Avoid sudden starts, exces- sive speed and sudden stops. WARNING: Do not leave the seat of the tractor without disengaging the PTO and engaging the parking brake. If leaving the tractor unattended, turn the ignition key off and remove key. • Adjust the operator’s seat to the most comfort- able position that allow[...]

19 • To move in reverse, check that the area behind is clear then slowly depress the rear of the forward/reverse pedal. Figure 15 • When traveling short distances with frequent changes in direction, the forward/reverse rocker pedal may be operated using the heel/toe method. Place your foot on the center section of the pedal and press downward w[...]

20 • Fully depress and hold the differential lock pedal to engage the transmission differential lock. Release the pedal to disengage the differential lock. See Figure 17. Figure 17 NOTE: Because of the drive load on the internal engagement mechanism, releasing the differential lock pedal may not always disengage the differential lock. It may be n[...]

21 • Shift the PTO lever forward to select the mid PTO. The mid PTO is used to drive equipment designed to operate at an input speed of 2000 RPM. Refer to Figure 19. • Shift the PTO lever to the middle position to select both the mid PTO and rear PTO. In this position the mid PTO and rear PTO will run simultaneously when the PTO switch is activ[...]

22 Hazard Lights Always use the flashing amber hazard lights along with the SMV (Slow Moving Vehicle) emblem when operating the tractor on, or near, roadways. Also activate the hazard lights when necessary to warn others that the tractor is being operated in the area. • To turn on the flashing hazard lights, depress the top end of the hazard ligh[...]

23 TRACTOR WEIGHTING When implements are installed on either the front or rear of the tractor, the normal balance of the tractor is altered. • As a rear mounted implement is raised to the transport position, the balance point of the tractor shifts rearward, which may result in a loss of steering control and tractor stability. • When a front mou[...]

24 SECTION 3: ADJUSTMENTS ADJUSTING THE SEAT For the comfort of the operator, a single lever adjustable seat is provided to set the fore to aft position of the seat. Adjust the seat to the most comfortable position that allows you to operate all controls and pedals. WARNING: Do not adjust the seat when the tractor is moving, as this could cause the[...]

25 • The length of the upper hitch link is normally determined by the design of each implement. To adjust the upper hitch link, loosen the jam nut and turn the adjustment tube as shown in Figure 25. After the appropriate length is at- tained, tighten the jam nut. If correctly adjusted, the upper hitch link will be parallel or nearly parallel to t[...]

26 ADJUSTING THE BRAKES The tractor brakes are adjusted at the factory and should experience minimal wear if the tractor is operated normally. However, all brake pads are subject to wear and at some point the brake linkage may have to be adjusted. Check the brake linkage as follows: • Place the tractor on a level surface. • Stop the tractor eng[...]

27 SECTION 4: MAINTENANCE The service life and reliability of any machine depends upon the care it is given. Proper lubrica- tion and maintenance is a vital part of that care. Using the Lubrication and Maintenance Chart as a guide, monitor the hourmeter on the instrument panel to ensure the required maintenance proce- dures are performed. The maint[...]

28 LUBRICATION AND MAINTENANCE CHART (ILLUSTRATION) 11 19 1 2 5 3 4 5 5 8 6 6 7 9 10 14 14 17 12 18 16 13 16 16 16 15 18 21 20 9[...]

29 LUBRICATION AND MAINTENANCE CHART † More often when operating under dusty conditions Ref. No. Operation to be Performed Service Intervals B e f o r e eac h u se E ve r y 10 H ou r s E ve r y 25 H ou r s E ve r y 50 H ou r s E ve r y 100 H ou r s E ve r y 150 H ou r s E ve r y 200 H ou r s E ve r y 300 H ou r s E ve r y 600 H ou r s B e f o r e[...]

30 ACCESSING THE ENGINE COMPARTMENT WARNING: If the tractor has been recently operated, engine surfaces (including the radiator) will be HOT. Allow the engine to cool before open- ing the hood, or use extreme caution to avoid burns when the hood is open. To raise the hood, locate the latch release lever in the hood notch at the front of the tractor[...]

31 • Since battery acid is corrosive, do not pour it into any sink or drain. Before discarding an empty electrolyte container, rinse it thoroughly with a neutralizing solution. • NEVER connect (or disconnect) battery charger clips to the battery while the charger is turned on, as it can cause sparks. • Keep all sources of ignition (cigarettes[...]

32 HEAD LIGHT BULB REPLACEMENT The tractor is equipped with four headlight bulbs. If one of the bulbs should burn out, replace the bulb as follows: • Fully raise the hood so that the hood prop link holds the hood in the raised position. • Pull both locking tabs of the wire harness plug away from the bulb/socket assembly and unplug the wire harn[...]

33 INSTRUMENT PANEL BULB REPLACEMENT Referring to the instrument panel information pro- vided in the CONTROL AND FEATURES section of this manual, regularly check to ensure that the instrument panel light bulbs are functioning. To change a burned out instrument panel bulb: • Raise the tractor hood to view the back side of the instrument panel. •[...]

34 Main Fuse The main fuse in the tractor wire harness protects the tractor’s entire electrical system. A blown main fuse will prevent battery current from passing though the harness. To replace the main fuse: • Raise the tractor hood and remove the right side panel. • Locate the main fuse under the dash panel, along the tractor’s right fra[...]

35 • If the oil level is low, ad d Cub Cadet hy draul ic oil. Loosely p osit ion a fu nnel in the fill hole so that the r e i s enough c l earan c e around t he fun- nel to allo w t h e transmission t o vent while the oil is poured into t he trans m i s sio n. Fi l l ONLY to th e f ull ma rk, never o v erfill the t ran s mission. NOTE: Always use[...]

36 CHANGING HYDROSTATIC TRANS MISSION AND HYDR AUL IC SYSTEM OIL FILTERS NOTE: E xcept for the initial break-in period oil filter change, the hy drostatic t ran s m ission and hydraulic system oil f ilters shoul d be changed al ong with the hydro stati c transmis sion / hydrauli c system o i l aft er every 200 hours of operation. Init ial Break-I n[...]

37 CHECKING OIL LEVEL IN FRONT AXLE AND FINAL REDUCTION GEAR CASES. Check the front axle and final reduction gear case oil levels after every 50 hours of operation. Check the oil level only while the engine is stopped and the tractor is standing on a level surface. Check Front Axle Oil The oil fill plu g/ dipstick is located on the left side of the[...]

38 • Place a suitable container beneath the front of the axle housing. • Remove the oil fill plug/dipstick to help vent the axle, then remove the drain plug and allow the oil to drain into the container. Reinstall the drain plug after draining the oil. See Figure 46. • Fill the axle with Cub Cadet Gear Lube until the oil level reaches the ful[...]

39 TIRE MAINTENANCE Check the tire air pressure after every 50 hours of operation or weekly. Keep the tires inflated to the recommended pressures. Improper inflation will shorten the service life of a tire. See the tire side wall, or the Tire Inflation chart, for proper inflation pressures. Observe the following guidelines: • Do not inflate a tir[...]

40 3. Clean the engine and the entire tractor thoroughly. 4. Fill the fuel tank with FRESH high grade Number Two diesel fuel. 5. Remove the glow plugs and pour a small amount of engine oil into each cylinder. Reinstall the glow plugs and slowly crank the engine to distribute the oil. 6. Fully charge the battery, then disconnect the negative cable a[...]

41 SECTION 5: ENGINE INFORMATION AND MAINTENANCE Daihatsu L.L.C., the California Air Resources Board (CARB) and the United States Environmental Protection Agency (U.S. EPA) Emission Control System Warranty Statement (Owner’s Defect Warranty Rights and Obligations) EMISSION CONTROL WARRANTY COVERAGE IS APPLICABLE TO CERTIFIED ENGINES PURCHASED IN [...]

42 c. Ignition System For Gasoline For Diesel • Spark plug(s) • Glow plug • Ignition coil • Ignition processor d. Exhaust System • Exhaust manifold e. Miscellaneous Items Used in Above Systems • Vacuum, temperature, position, time sensitive valves and switches • Electronic controls • Connectors and assemblies • Hoses 2. Length of [...]

43 ENGINE MAINTENANCE WARNING: Use care when servicing any component in the engine area. If the engine has recently been operated, components will be hot and could cause burns. Allow the engine to cool before servicing. WARNING: Before servicing the engine, place the tractor on a level surface, stop the engine, engage the parking brake, and remove [...]

44 ADDING ENGINE OIL WARNING: Never overfill the engine crankcase. The engine may overheat and/or damage may result if the crankcase is below the “ADD” mark or over the “FULL” mark on the dipstick. For best results, fill to the “FULL” mark on the dipstick as opposed to adding a given quantity of oil. Always check the level on the dipsti[...]

45 • Remove the filter by turning it counterclockwise using an automotive type filter wrench to loosen. See Figure 53. Figure 53 • Reinstall the drain plug in the engine and clean up any residual oil. Refer to Figure 52. • Apply a light coating of clean oil on the gasket of the new oil filter. Thread the filter on by hand until the gasket con[...]

46 • Start the engine and allow it to run for a short period. Stop the engine. • Recheck the coolant level in the overflow reservoir and refill as needed. Reinstall the reservoir cap. INSPECTION OF COOLING SYSTEM HOSES Check the cooling system hoses and fan belt for any cracks or deterioration after every 100 hours of operation. Check for loose[...]

47 • Pull the air cleaner element from the housing. See Figure 56. Figure 56 • Lightly blow or brush loose debris from the air cleaner element. Clean any debris from the housing. • Inspect the paper pleats of the cleaner element for damage and dirt. Inspect the sealing surface on the inner end of the element for deterioration or damage. Repla[...]

48 Changing The Fuel Filter Replace the fuel filter cartridge after every 600 hours of operation. NOTE: There is no shut off valve in fuel system. To stop the flow of fuel while replacing the filter, it will be necessary to carefully clamp the fuel line between the fuel tank and the filter. • Place a suitable container beneath the filter cup. •[...]

49 SECTION 6: SPECIFICATIONS Engine Manufacturer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Diahatsu Horsepower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Cylinders . . . . . . . . . . . . . [...]

50 SPECIFICATIONS Hydraulic Lift System Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Auxiliary Pump-Gear Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Position Control Lever Pump Capacity . . . . . . . . . . . . . [...]

51 SECTION 7: OPTIONAL EQUIPMENT AND ACCESSORIES When purchasing your tractor, you probably had it equipped for your particular needs at that time. You may later wish to obtain additional equipment or accessories to perform other tasks. Refer to the chart below for a list of optional equipment and accessories currently available through your Cub Ca[...]

Proper maintenance of your Cub Cadet equipment is the owner’s responsibility. Follow the instructions in your owner’s manual for correct lubricants and maintenance schedule. Your Cub Cadet dealer carries a complete line of genuine Cub Cadet parts and quality lubricants and filters for your equipment’s engine, transmission, chassis and attachm[...]