D-Link DCS-5230 инструкция обслуживания

[...]

2 D-Link DCS-5230 User Manual T able of Contents Product Overview ........................................................ 3 Package Contents ................................................... 3 System Requirements ............................................. 3 Introduction .............................................................. 4 Hardware[...]

3 D-Link DCS-5230 User Manual Section 1 - Product Overview • D- Li nk D C S- 52 30 W i re le ss N PT Z Ne tw o rk C am er a • CAT5 Ethernet Cable • Power Adapter • Manual and Software on CD • Quick Install Guide • Camera Stand • Mounting Screws Note: Using a pow er supply with a diff erent voltage than the one included with y our prod[...]

4 D-Link DCS-5230 User Manual Section 1 - Product Overview Introduction D-Link’s 1.3 Megapixel DCS-5230 is a 802.11n (draft) wireless ptz network camera designed with home and SOHO users in mind. The DCS-5230 delivers high quality real-time videos in MPEG-4 and JPEG allowing optimization for both image quality and bandwidth-efciency. The 1 Lux[...]

5 D-Link DCS-5230 User Manual Section 1 - Product Overview Hardware Over view Microphone This built-in microphone can be used capture audio from sources nearby the camera. Camera Dome This clear dome houses the camera lens and protects the pan/tilt/zoom apparatus. Front Pyroelectric Infrared (PIR) Sensor This sensor is used to detect motion based o[...]

6 D-Link DCS-5230 User Manual Section 1 - Product Overview WPS Button Press this button to establish a WPS connection. MicroSD Slot Insert a standard MicroSD card into this slot for image storage. WPS LED The WPS LED will blink blue when initializing a connection, and illuminate with solid blue once the connection has been established. Power/Link L[...]

7 D-Link DCS-5230 User Manual Section 1 - Product Overview DC Power Connector The DC Power input connector is labeled DC 12V with a single jack socket to supply power to the DCS-5230. Ethernet Cable Connector Th e D CS -5 230 f ea tu res a RJ -4 5 c on nect or fo r c on ne ctio ns to 10 Ba se -T Ethernet cabling or 100Base-TX Fast Ethernet cabling.[...]

8 D-Link DCS-5230 User Manual Section 1 - Product Overview Bottom Panel Mounting Socket The silver mounting stand can be connected here if needed. Reset Button Depress this button with a straightened paper clip for about 20 seconds to reset the camera to factory default settings.[...]

9 D-Link DCS-5230 User Manual Section 1 - Product Overview Mounting Slots These slots can be used to mount the camera against a wall using protruding bolts, nails, or screws. Mounting Stand Th is st and ca n b e mou nte d a to p or o n th e b ot tom of th e enclosure depending on the camera’s orientation. Rear Panel[...]

10 D-Link DCS-5230 User Manual Section 1 - Product Overview Hardware Installation Standard Orientation Attach the silver mounting stand above the dome of the camera. Tighten the nut on the top of the mounting stand using a coin or a screwdriver. Inverted Orientation Set the mounting onto a at surface. Slide the camera down vertically onto the st[...]

11 D-Link DCS-5230 User Manual Section 1 - Product Overview Cable Installation Connect an Ethernet cable to the Ethernet port located on the camera’s back panel and attach it to the network. Note: An Ether net cable is required dur ing initial setup . Onc e y ou r w ir el ess c on figur ati on has been set up , you ma y disconnect the Ether net [...]

12 D-Link DCS-5230 User Manual Section 1 - Product Overview MicroSD Card Installation Locate the MicroSD slot on the side of the camera. Push a MicroSD card into the slot until it clicks into place. Note: To remove a MicroSD card, gently push the card in and it will eject.[...]

13 D-Link DCS-5230 User Manual Section 1 - Product Overview As the Digital Input signal is controlled by an external device, we recommend that you set your device to feed no current normally, and feed a 12V current only to trigger a DI event on the DCS-5230. Example use of DI/DO: You can connect a motion sensor to the DI port, signaling the camera [...]

14 D-Link DCS-5230 User Manual Section 2 - Installation Wireless Installation Considerations The DCS-5230 can be accessed using a wireless connection from virtually anywhere within the operating range of your wireless network. Keep in mind, however, that the quantity, thickness and location of walls, ceilings, or other objects that the wireless sig[...]

15 D-Link DCS-5230 User Manual Section 3 - Configuration D-Link Setup Wizard DCC will show the MAC address and IP address of your DCS-5230. If you have a DHCP* server on your network, there will be a valid IP Address displayed at the end of DCC process. You can begin to use the IP camera now. *A DHCP server is a device that supplies IP Addresses t[...]

16 D-Link DCS-5230 User Manual Section 3 - Configuration UPnP (Universal Plug and Play) is a networking architecture that provides compatibility among networking equipment, software, and peripherals. The DC S- 52 30 is an UPnP enabled Internet camera. If your operating system is UPnP enabled, the device will be easier to congure. If you do not [...]

17 D-Link DCS-5230 User Manual Section 3 - Configuration The following screen will appear. Select Networking Services. Select Universal Plug and Play. Click Details Click Add/Remove Windows Components Click OK[...]

18 D-Link DCS-5230 User Manual Section 3 - Configuration Please wait while Setup congures the components. Click Next Click Finish[...]

19 D-Link DCS-5230 User Manual Section 3 - Configuration To view your DCS-5230 Internet Camera in an Internet browser, go to your Desktop and click My Network Places . Click DCS-5230 (192.168.0.120).[...]

20 D-Link DCS-5230 User Manual Section 3 - Configuration After you click on the DCS-5230 icon, your Internet browser will automatically be opened to the IP Address of the DCS-5230, in this example it is: http://192.168.0.120. Your DCS-5230 may have a different IP Address. http://192.168.0.120/eng/index.cgi[...]

21 D-Link DCS-5230 User Manual Section 3 - Configuration Setting up a Wireless Connection with WPS If your wireless access point or router supports push-button Wireless Protected Setup (WPS), you can quickly congure your wireless network and camera without using the camera’s web interface. After plugging the power adapter to your camera and t[...]

22 D-Link DCS-5230 User Manual Section 3 - Configuration The window in the center of your browser is the camera image window. You should now see a video image and hear the audio over your comp uter speaker s from the DCS- 5230 . If you are having problem s, pleas e consul t the Troub lesho otin g section of this manual (page 79). O p e n yo ur In [...]

23 D-Link DCS-5230 User Manual Section 3 - Configuration After all the router settings have been entered correctly, a PC user inside or outside your network will have access to the camera through the Internet Explorer Web browser. To access the camera from the Internet, type the IP Address of the router given to you by your ISP, followed by a colo[...]

24 D-Link DCS-5230 User Manual Section 3 - Configuration Open your Internet Explorer Web browser and enter the IP address for your Internet Camera (http://192.168.0.120). In the example, this address is 192.168.0.120. Your address may differ. If a window appears asking to install a Verisign certicate for authentication click Yes . This allows t[...]

25 D-Link DCS-5230 User Manual Section 3 - Configuration Click on the Client Setup button to change settings related to the camera connection. Click on the Logout butt on to logo ut from the camera server and close the browser. Use the Pan / Tilt / Zoom Action Pad to co nt ro l th e cam era’ s pa n or ti lt. Th e lar ge tre e icon controls the z[...]

26 D-Link DCS-5230 User Manual Section 3 - Configuration Video Profile: Full Screen: Snapshot: Record Video: Set Path: Start/Stop Audio: Start/Stop T alking: Start/Stop Digital Output: You can change between your different viewing proles, which you can set up in SETUP > Audio and Video. This allows you to view the video in full screen mode.[...]

27 D-Link DCS-5230 User Manual Section 3 - Configuration There are 5 tabs across the top of the Conguration screen. The LIVE VIDEO page is used for viewing live video and audio. The SETUP page is used for basic setup of the DCS-5230. The MAINTENANCE page is use d for serv er syst em maintenance. The STATUS page will show the camera’s status a[...]

28 D-Link DCS-5230 User Manual Section 3 - Configuration Wizard The setup wizards guide you through initial setup of your IP camera. You can use the Internet Connection Setup Wizard for initial network setup, and you can use the Motion Detection Setup Wizard to set up motion detection and snapshots. Simply follow the instructions given in each ste[...]

29 D-Link DCS-5230 User Manual Section 3 - Configuration DCS-5230 will request a new IP address from the DHCP server every time it restarts. Once the DCS- 523 0 is con gur ed, this rad io sho uld be desel ect ed at all times. If this radio button has been selected and the connection is lost, run the DCC nd the camera’s IP address. Necessar[...]

30 D-Link DCS-5230 User Manual Section 3 - Configuration PPPoE Settings: HTTP Port: RTSP Port: Note: If you are using a PPPoE connection, enable it and enter the User Name and Password for your PPPoE account. You can get this information from your Internet service provider (ISP). This is the port that allows the user to connect to the camera’s u[...]

31 D-Link DCS-5230 User Manual Section 3 - Configuration To set up your IP camera’s wireless network interface settings, enable Wireless Settings in this window rst. Then continue the further conguration next. Clicking this button will scan for available wireless networks. After scanning, you can use the drop- down box to select an availab[...]

32 D-Link DCS-5230 User Manual Section 3 - Configuration Dynamic DNS Check this checkbox to enable the DDNS function of the camera. Use the drop-down box to the right to select a DDNS service to use. Type in the Host Name of the DDNS service you wish to use. Enter your User Name for the DDNS service you wish to use. Enter the password for the DDNS[...]

33 D-Link DCS-5230 User Manual Section 3 - Configuration This adjusts the brightne ss of the camera image. This is set to 35 by default. This adjust s the color satura tion of the camera image. This is set to 40 by default. This adjus ts the contrast of the camer a image. This is set to 40 by default. This option adjusts the camera sensor’s to p[...]

34 D-Link DCS-5230 User Manual Section 3 - Configuration You can set the camera’s sensor output to VGA quality (640x480), XGA quality (1024x768), or SXGA quality (1280x1024). Note: When using SXGA mode, please note that motion de te ctio n an d mo tion tri gg ered sna psho ts wil l be dis ab led an d th at rec ord in gs wil l be do ne at a ma xi[...]

35 D-Link DCS-5230 User Manual Section 3 - Configuration JPEG Quality: RTSP URL: Night Mode: Enable Night Mode: Shutter: Enable Speaker: Volume: Enable Microphone: Volume: This sets the JPEG quality of any manual snapshots you take when this video prole is selected. This setting allows you to set a sufx for your camera’s RTSP URL, so you c[...]

36 D-Link DCS-5230 User Manual Section 3 - Configuration Click this box to enable the PIR sensor. Click this box to enable video motion detection. This setting adjusts how sensiti ve the ca mera wil l be to mot ion, whe re 10 0% will be the most sensitive setting and 0% will be the least sensitive setting. This will allow you to draw motion detect[...]

37 D-Link DCS-5230 User Manual Section 3 - Configuration The motion notication will continue to blink as long as motion is detected. If no additional motion is detected, it will return to its original state after eight seconds. The red grid on the right indicates an area that has been selected for motion detection. When motion is detected, the [...]

38 D-Link DCS-5230 User Manual Section 3 - Configuration Used to adjust the hour of time servers for local settings. Check this to enable daylight saving time. Set dayl ight savi ng time star t and end dat e by your local denition. Synchronize with the NTP server over the Internet whenever the DCS-5230 starts up. It will fail if the assigned ti[...]

39 D-Link DCS-5230 User Manual Section 3 - Configuration Preset Position Click the Preset Position button from the left side of the Setup screen to access settings that affect how the DCS-5230 Internet Camera can pan and move to preset locations. Select the speed at which the camera will pan for a full cycle from the drop-down list. Select a value[...]

40 D-Link DCS-5230 User Manual Section 3 - Configuration Use the Set As Home button to set the current position as the home position. The Home position is the rst position the camera goes to after the camera boots. You can also recall the default home position, use the Default Home button. To use the Auto Patrol feature, select the desired pres[...]

41 D-Link DCS-5230 User Manual Section 3 - Configuration Check this checkbox to enable the recording feature. After enabling recording, you will need to select a location to record to (SD Card or Samba network drive), and you will need to select a scheduling method. Selecting this will allow you to record to an SD Card inserted into the SD slot on[...]

42 D-Link DCS-5230 User Manual Section 3 - Configuration Note: You can create a simple Samba network drive on your Windows PC by right-clicking a folder, selecting Sharing and Security… , and selecting Share this folder . Enter a Share name you would like to use for the folder, then click the Permissions button and check the box for Full Control[...]

43 D-Link DCS-5230 User Manual Section 3 - Configuration Example: Using motion detection triggered recording and setting Prerecord to 5 seconds and Postrecord to 9 seconds, the camera will save video from 5 seconds before motion was detected to 9 seconds after motion was detected. This will set the camera to record continuously. This scheduling me[...]

44 D-Link DCS-5230 User Manual Section 3 - Configuration Check this box to enable the snapshot feature. This will set the camera to take a snapshot whenever motion is detected. This will set the camera to take a snapshot whenever a signal is sent to the D/I input. You can nd more information about the DI/DO interface at the end of this document[...]

45 D-Link DCS-5230 User Manual Section 3 - Configuration Check this box to enable the D/O port. When checked, the D/O port will send a signal whenever motion is detected by the camera. (When motion detection has been enabled) When checked, the D/O port will send a signal whenever a signal is detected on the Digital In (D/I) port. Note: If the came[...]

46 D-Link DCS-5230 User Manual Section 3 - Configuration Maintenance Admin The DCS -52 30 is con gur ed wit hou t any pas swor ds by def aul t. Thi s allows anyone to access and congure the DCS-5230 as long as the IP address is known. Therefore, for security it is best to specify a password to restrict others from accessing your camera. Type[...]

47 D-Link DCS-5230 User Manual Section 3 - Configuration Password for the Administrator’s account. The administrator password must be entered in twice for conrmation. Create a new user for accessing the video image. A maximum of twenty user accounts can be added. The new user name will be displayed in the list of user names below. Administrat[...]

48 D-Link DCS-5230 User Manual Section 3 - Configuration Click Apply on this screen to restore the factory default settings. After conrmation, the system will restart and require the DCC program to locate the IP address of the DCS-5230. System Clicking Save Conguration allows you to save a copy of the camera’s current conguration to a l[...]

49 D-Link DCS-5230 User Manual Section 3 - Configuration This option allows you to upgrade the rmware via a web browser. Click on Browse to locate the rmware le and then click on Upgrade to apply the rmware to the camera. File Path: Firmware Update[...]

50 D-Link DCS-5230 User Manual Section 3 - Configuration The Device Info screen lists the following important settings that are currently set for the DCS-5230: • Camera Name • Time & Date • Firmware Version • Mac Address • IP Address • IP Subnet Mask • Default Gateway • Primary DNS • Secondary DNS • PPPoE • DDNS Device In[...]

51 D-Link DCS-5230 User Manual Section 3 - Configuration Log The content of the log le reveals useful information about the current conguration and connection logged after the DCS-5230 starts up. This option enables the camera to send camera log les to a remote server. The IP address of the remote server. The port number of the remote log[...]

52 D-Link DCS-5230 User Manual Section 3 - Configuration The help page provides detailed information for the camera’s Web interface. Help[...]

53 D-Link DCS-5230 User Manual Section 4 - D-ViewCam Installation D-ViewCam Installation D- Vi ew Cam sof twar e is inc lude d to ma nage up to 32 came ras sim ulta neou sly, sen d aut om at ed e-ma il aler ts, and reco rd video to your hard drive when motion is detected or according to a set schedule. Insert the so ft wa re CD into the CD-ROM driv[...]

54 D-Link DCS-5230 User Manual Section 4 - D-ViewCam Installation Click Next to continue. Click Browse to choose a specic folder for the installation, otherwise click Next to continue. Click Next Click Next[...]

55 D-Link DCS-5230 User Manual Section 4 - D-ViewCam Installation Click Next to start the installation. Note: The D-ViewCam installation process may take several minutes to complete. Click Next Click Finish to complete the installation. Click Finish[...]

56 D-Link DCS-5230 User Manual Section 4 - D-ViewCam Installation Adding a Camera To start D-ViewCam, select Start > All Programs > D-Link > D-Link D-ViewCam . Enter Admin as the default user name and leave the password blank. Click to log into the system. This section will show you how to add a camera to the D-ViewCam system.[...]

57 D-Link DCS-5230 User Manual Section 4 - D-ViewCam Installation The Add Camera Wizard screen will appear. Use this wizard to add your cameras to the D-ViewCam system. Note: Use the left or right arrow icons for navigation within the wizard. Click / Next to continue. Click Next[...]

58 D-Link DCS-5230 User Manual Section 4 - D-ViewCam Installation Choose the method to add your camera(s). You can sel ect Auto Discovery to automatically search for your camera(s), or Add Manually to add your camera(s) via the camera’s IP address. Click Next to continue. If you selected Auto Discovery , the system will search all available came [...]

59 D-Link DCS-5230 User Manual Section 4 - D-ViewCam Installation D-ViewCam shows the detected IP camera(s) information. You can choose and schedule recordings for each camera. • 24/7 Continuous Recording : Continuous recording - 24 hours a day, 7 days a week. • 24/7 Motion Detection Recording : Continuous monitoring, but records ONLY when moti[...]

60 D-Link DCS-5230 User Manual Section 4 - D-ViewCam Installation Select Yes to add other camera(s), or select No if you have no additional camera(s) to be added. Click Next to continue. The Add Camera wizard is now complete. Click Close to access the D-ViewCam’s main screen. Y our D-ViewCam Installation is Complete! Note: Please refer to the D-V[...]

61 D-Link DCS-5230 User Manual Section 4 - Security Wireless Security This section will show you the different levels of security you can use to protect your data from intruders. The DCS-5230 offers the following types of security: • WPA-PSK (Pre-Shared Key) • WEP (Wired Equivalent Privacy) What is WEP? WEP stands for Wired Equivalent Privacy. [...]

62 D-Link DCS-5230 User Manual Section 4 - Security What is WP A? WPA, or Wi-Fi Protected Access, is a Wi-Fi standard that was designed to improve the security features of WEP (Wired Equivalent Privacy). The 2 major improvements over WEP: • Improved data encryption through the Temporal Key Integrity Protocol (TKIP). TKIP scrambles the keys usi ng[...]

63 D-Link DCS-5230 User Manual Section 4 - Security D-Link’s DCS-5230 is a versatile and cost effective Internet Camera offering both video and audio monitoring. It can also serve as a powerful surveillance system in security applications. The DCS-5230 can be used with any wired or 802.11n/g wireless router. This section explains how to view the [...]

64 D-Link DCS-5230 User Manual Section 4 - Security Run the setup wizard from the CD included with the DCS-5230. Follow the steps in the Quick Installation Guide to congure the DCS-5230. The camera will be assigned a local IP Address that allows it to be recognized by the router. Write down this IP Address for future reference. 1. Assign a Local[...]

65 D-Link DCS-5230 User Manual Section 4 - Security Run your Internet Explorer Web browser. In the address bar, type in the IP Address that was assigned to the Internet Camera by the DCC program. The DCS-5230 Live Video Page appears with a wind ow displaying live video from the camera. You are able to view this screen from any PC running Internet E[...]

66 D-Link DCS-5230 User Manual Section 4 - Security The Setup > Network Setup page displays the port settings for your camera. If necessary, these ports can be changed if they are already in use by other devices (e.g. in a multiple camera environment). Note: Both the HTTP port and RTSP port are required to be opened for the DCS-5230. Please refe[...]

67 D-Link DCS-5230 User Manual Section 4 - Security The following steps generally apply to any router that you have on your network. The D-Link DIR-655 is used as an example to clarify the conguration process. Congure the initial settings of the DIR-655 by following the steps outlined in the DIR-655 Quick Installation Guide. 3. Access the Rou[...]

68 D-Link DCS-5230 User Manual Section 4 - Security Note: Because a dynamic WAN IP can change from time to time depending on your ISP, you may want to obtain a Static IP address from your ISP. A Static IP address is a xed IP address that will not change over time and will be more convenient for you to use to access your camera from a remote loca[...]

69 D-Link DCS-5230 User Manual Section 4 - Security Repeat the above steps adding the port 554 to both the Public and Private Port sections. A check mark appearing before the entry name will indicate that the ports are enabled. Important: Some ISPs block access to port 80 and other commonly used Internet ports to conserve bandwidth. Check with your[...]

70 D-Link DCS-5230 User Manual Section 4 - Security To enable mobile device video streaming, you will need to congure for mobile viewing (see below). Using & Configuring 3G Compatible Cell Phones[...]

71 D-Link DCS-5230 User Manual Section 4 - Security The following steps are based on a Nokia 6630 cell phone. Play from RealPlayer Press the Menu button and select Media Select Open Select RealPlayer[...]

72 D-Link DCS-5230 User Manual Section 4 - Security Select Open When RealPlayer opens, press Options[...]

73 D-Link DCS-5230 User Manual Section 4 - Security Select Download Select Video Clips Press Options Note: 71.34.50.5 is the camera’ s IP address in this sample.[...]

74 D-Link DCS-5230 User Manual Section 4 - Security Select Navigation Options Select Go to web address Input your rtsp address[...]

75 D-Link DCS-5230 User Manual Section 4 - Security Press Yes , and allow Connection and Loading of the streaming video. Enjoy streaming video on your cellphone.[...]

76 D-Link DCS-5230 User Manual Section 4 - Security Play from PVPlayer Press the Menu button and select PVPlayer Select Open Press the Options button[...]

77 D-Link DCS-5230 User Manual Section 4 - Security Select Open location Input your rtsp address Note: 71.34.50.5 is the camera’ s IP address in this sample.[...]

78 D-Link DCS-5230 User Manual Section 4 - Security Enjoy streaming video on your cellphone.[...]

79 D-Link DCS-5230 User Manual Section 5 - T roubleshooting 1 What is an Internet Camera? The Internet Camera is a stand-alone system connecting directly to an Ethernet or Fast Ethernet network. It differs from a conventional PC Camera, the Internet Camera is an all-in-one system with built-in CPU and Web-based solutions providing a low cost soluti[...]

80 D-Link DCS-5230 User Manual Section 5 - T roubleshooting 8. Can the DCS-5230 be connected to the network if it consists of only private IP addresses? Yes, the Internet Camera can be connected to a LAN with private IP addresses. 9. Can the DCS-5230 be installed and work if a rewall exists on the network? If a rewall exists on the network, p[...]

81 D-Link DCS-5230 User Manual Section 5 - T roubleshooting 12. I connected the Internet Camera directly to a computer with a cross-over cable Ethernet cable and received the following Windows error upon running the Installation Wizard: This Windows error will occur if the Internet Camera is connected to a computer that is not properly congured [...]

82 D-Link DCS-5230 User Manual Appendix A - Wireless Basics D-Link wireless products are based on industry standards to provide easy-to-use and compatible high-speed wireless connectivity within your home, business or public access wireless networks. Strictly adhering to the IEEE standard, the D-Link wireless family of products will allow you to se[...]

83 D-Link DCS-5230 User Manual Appendix A - Wireless Basics What is Wireless? Wireless or WiFi technology is another way of connecting your computer to the network without using wires. WiFi uses radio frequency to connect wirelessly, so you have the freedom to connect computers anywhere in your home or ofce network. Why D-Link Wireless ? D-Link [...]

84 D-Link DCS-5230 User Manual Appendix A - Wireless Basics Who uses wireless? Wireless technology as become so popular in recent years that almost everyone is using it, whether it’s for home, ofce, business, D-Link has a wireless solution for it. Home • Gives everyone at home broadband access • Surf the web, check e-mail, instant message,[...]

85 D-Link DCS-5230 User Manual Appendix A - Wireless Basics Using a D-Link Cardbus Adapter with your laptop, you can access the hotspot to connect to Internet from remote locations like: Airports, Hotels, Coffee Shops, Libraries, Restaurants, and Convention Centers. Wireless network is easy to setup, but if you’re installing it for the rst tim[...]

86 D-Link DCS-5230 User Manual Appendix A - Wireless Basics There are basically two modes of networking: • Infrastructure – All wireless clients will connect to an access point or wireless router. • Ad-Hoc – D ire ctl y c onn ec tin g to an oth er com put er , fo r pe er -to -p eer co mmu ni cat ion , u sin g wir ele ss n et wor k adapters [...]

87 D-Link DCS-5230 User Manual Appendix B - Networking Basics Networking Basics Check your IP Address After you install your new D-Link adapter, by default, the TCP/IP settings should be set to obtain an IP address from a DHCP server (i.e. wireless router) automatically. To verify your IP address, please follow the steps below. Click on Start > [...]

88 D-Link DCS-5230 User Manual Appendix B - Networking Basics Statically Assign an IP Address If you are not using a DHCP capable gateway/router, or you need to assign a static IP address, please follow the steps below: Step 1 Windows ® XP - Click on Start > Control Panel > Network Connections . Windows ® 2000 - From the desktop, right-clic[...]

89 D-Link DCS-5230 User Manual Appendix C - T echnical Specifications T echnical Specifications Network Protocol Support IPv4, ARP, TCP, UDP, ICMP, DHCP Client, NTP Client (D-Link), DNS Client,  DDNS Client (D-Link), SMTP Client, FTP Client, HTTP Server, Samba Client, PPPoE, RTP, RTSP, RTCP, 3GPP Built-in Network Interfaces 802.11 n/g Wireless[...]

90 D-Link DCS-5230 User Manual Appendix C - T echnical Specifications Security Administrator and user group protected  Password authentication  Wireless LAN security:64/128-bit WEP, WPA-PSK and WPA2 data  encryption Viewing System Requirements OS: Microsoft Windows XP, 2000 / Vista/ Linux/ MAC OS X10.3 or above  Browser: Internet Explo[...]

91 D-Link DCS-5230 User Manual Appendix C - T echnical Specifications Emission (EMI), Safety & Other Certications FCC Class B  IC  CE  C-Tick  Package Includes DCS-5230 camera  External power adapter  CAT5 Ethernet cable  Quick Installation Guide  Master CD  Camera stand  Mounting Screws  Version 1.0 07/14/2[...]