Datalogic Scanning 9504 инструкция обслуживания

Magellan ® 9500/9500 Ω 9504/9504 Ω with SmartSentry ® Product Reference Guide[...]

Datalogic Scanning, Inc. 959 T erry Street Eugene, Oregon 97402 T elephone: (541) 683-5700 F ax: (541) 345-7140 An Unpublished W ork - All r ights reser ved. No part of the contents of this documentation or the procedures described therein may be reproduced or transmitted in an y form or by an y means without pr ior written per mission of Datalogic[...]

Product Reference Guide 1 Table of Contents Chapter 1. Introduction ................. ............................................. ...................... 1-1 Manual Overview ........................... ............................................................................. 1-1 How to Use This Manual .... .....................................[...]

2 Magellan ® 9500 Viewing Angle ................................ ..................................................................... 2-28 Placing and Installing the Remote Scale Display ........ .............................................. 2-29 Changing Weighing Modes ............................................................................[...]

Product Reference Guide 3 Shift Test (Metric) ............ ................................................................................... 5-12 Increasing- Load Test (Phase 2) ........................................ .................................... 5-13 Blanking Test .......................... ..............................................[...]

4 Magellan ® 9500 EAS Deactivation Duration — Retry ................................. ...................................... 6-57 EAS Deactivation Duration — Manual ............................... ...................................... 6-58 Interface Related Features .............................................................................[...]

Product Reference Guide 5 UPC-A Enable ....................................... .................................................................. 6-121 UPC-A Number System Character Tr ansmission .................. .................................. 6-122 UPC-A Check Character Transmis sion ....................................... ..................[...]

6 Magellan ® 9500 RSS-14 Check Character Transmis sion ..................................... ............................ 6-176 RSS-14/EAN-128 Emulation .... ........................................................................... 6-177 RSS-14 2D Component Enable ................................................ ............................ 6-17[...]

Product Reference Guide 7 I 2 of 5 Check Character Transm ission ...................................... ........................... 6-224 I 2 of 5 AIM ID ............................... .................................................................. 6-225 I 2 of 5 Label ID ...................... ..................................................[...]

8 Magellan ® 9500 Standard 2 of 5 Label ID . ................................................................................... 6-273 Standard 2 of 5 Length Cont rol ............................................... ............................ 6-274 Standard 2 of 5 Maximum Label Length ........................... ..................................[...]

Product Reference Guide 9 DATALOGIC SCANNING, INC. MAGELLAN ® END USER LICENSE AGREEMENT Notice to End User: The Data logic Product y ou have acquired cont ains embedded Software, which is integral to the product's ope ration. This Software is being provided to y ou under license, subject to the te rms and conditions of this Agre ement. If yo[...]

10 Magellan ® 9500 ing to Datalogic's standard assistance prac tices. Datalogic does not warr ant that the product will m eet End User's requirements or that use of the prod- uct will be uninterrupted or error free, or that Datalogic's remedial efforts will correct any no nconformance. This limited wa rranty does not co ver any prod[...]

Product Reference Guide 1-1 Chapter 1 Introduction This P roduct Reference G uide contains comprehensive instructions on how to install the scanner or scanner/scale (either model may be termed “ scanner” for the purpose of simplicity in this manual), how to pr ogram it using special programming feature ba r code labels, and advanced user inform[...]

1-2 Magellan ® 9500 Chapter 6 , Programming , details procedur es and provides custom bar- codes for setting programmable scanner and scanner/scale features. This chapter is organized by the categories: General F eatures, Interface Related F eatures and Symbology R elated F eatures. Appendix A , LED/Beeper Indications & Controls , lists the va[...]

Manual Overview Product Reference Guide 1-3 Manual Conventions ‘NO TE’ blocks contain inf ormation that is helpful and rec- ommended. They pro vide information that is critical to operations and/or procedures described in this manual. ‘LEGAL NO TE’ blocks indicate pr ocedures or activities which may be regulated under la w by governmental a[...]

1-4 Magellan ® 9500 Scanner and Scanner/Scale Nomenclature Controls, indicators and other nomenclature ar e shown in Figure 1-1 . Figure 1-1. Scanner/Scale Nomenclature Produce Rail All W eighs™ Platter Scanner LED (Green) Scale LED (Y ello w) We i g hin g Surf ace — Lean O v ersize Produce Her e V e rt i ca l Win d o w Horizont a l Win d o w [...]

Scanner and Scanner/Scale Nomenclature Product Reference Guide 1-5 Connectors The appearance of the connector panel will vary depending upon the fac- tory options purchased with your model. Reference Figure 1-2 . Figure 1-2. Connector Panel POS TERMINAL REMO TE DISPLA Y A UXILLIAR Y PORT SCALE HOST EAS PORT PO WER Connection to this port is Optiona[...]

1-6 Magellan ® 9500 Physical Parameters This chapter provides specifications for performance, environmental and electrical parameters. Reference the second chapter of this manual, Site Preparation and Installation , for physical measur ements of all models and some accessories. Scanning The scanner has a scan zone between the two windows wher e th[...]

Physical Parameters Product Reference Guide 1-7 Weighing S pecifications for scale capacity , settling time, minimum and maximum static weight, zeroing, and warm-up time are given belo w . For mor e infor- mation regarding the topic: Pr oper Weighing T echnique , refer to the Opera- tion and Maintenance chapter of this manual. Rated Weight Capacity[...]

1-8 Magellan ® 9500 Warm-Up Time There are two pertinent warm-up times that apply to the scanner or scan- ner/scale: Thermal Equilibrium When the unit is moved fr om a cooler temperature (such as a storage area) to a warmer environment (such as a checkstand location), 60 minutes must be allowed to acclimate the unit to ambient conditions prior to [...]

Physical Parameters Product Reference Guide 1-9 Figure 1-3. Environmental Specifications Operation S tora g e +40 C +104 F 10 C 50 F T emper a t u re 10 to +40 C 50 to +104 F D us t Re s i s t a nt Optic s C a vity , IP5X +70 C +15 8 F -40 C -40 F T emper a t u re -40 to +70 C -40 to +15 8 F Ill u min a tion Ar tifici a l Light: 0-450 Foot-c a ndle[...]

1-10 Magellan ® 9500 Electrical Specifications Before installation, always v erify that the site’ s electrical service meets the scanner/scale ’ s requirements. The scanner has been engineered for com- patibility with most international el ectrical systems operating in ranges from 100 to 240V AC at 50-60 Hz. V erify that the power source will [...]

Laser and Product Safety Product Reference Guide 1-11 Laser and Product Safety Laser safety requirements ar e based on IEC Standar d Pu blication 60825-1 (2001) and CDRH 21CFR, Chapter 1, Su bchapter J and (CDRH) Laser P roduct P erformance Standard, U ser information [1040.10(h)1]: • U ser Maintenance. N o user maintenance of the system other th[...]

1-12 Magellan ® 9500 Safety precautions to be taken: This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment R egulations. Cet appareil numerique de la classe A respecte toute les exigences du Reglement sur le material broilleur du Canada. CA UTION No adjustments or alteration of the scanner or scanner/[...]

Labeling Product Reference Guide 1-13 Labeling Regulatory , reference and safety labeling is shown in Figure 1-4 . Figure 1-4. Labeling Or ... Loc a ted on EA S S ingle-Antenn a model s Loc a ted in s ide Optic s Ch ass i s Loc a ted on S pider A ss em b ly ( S c a le Model s ONL Y) CLA SS 1 LA S ER PRODUCT LA S ER KLA SS E 1 CAT AGORIA 1 PRODUCTO [...]

1-14 Magellan ® 9500 Agency Compliances The scanner and scanner/scale meets or exceeds the r equirements for its device type as set forth by the following agencies and regulations: Contact Datalogic ® Product Marketing at (541) 683-5700, or your Data logic representative f or a complete listing of approv als for other countries. COUNTR Y COMPLIAN[...]

Bar Codes Supported Product Reference Guide 1-15 Bar Codes Supported The scanner can read/decode the following bar code types (symbologies): • UPC V ersions A & E • UPC S upplementals and Add-ons (2 & 5 digit supplimentals, Cou- pon code and Code 128) • Plural S tage Dual UPC Bar Codes for J apan ( 2 label read) • Reduced S pace Sym[...]

1-16 Magellan ® 9500 NOTES[...]

Product Reference Guide 2-1 Chapter 2 Site Preparation and Installation This chapter provides a r eference for preparing most checkstands to receive the scanner or scanner/scale. I ncluded are physical parameters and instructions for checkstand preparation, power and v entilation consider- ations, cable routing information and unit installation. Si[...]

2-2 Magellan ® 9500 Figure 2-1. 9500 Models Pre-Installation Considerations I t should be noted that the scope of this manual does not encompass all factors related to worker safety and checkstand design. I t does, however , offer a list of considerations that may be helpful in ensuring greater safety and productivity . Careful planning us ing the[...]

Checkstand Design Product Reference Guide 2-3 Checkstand Design 1. Select a design which allows load-sharing by sev eral muscle groups (for example designs which allow the cashier to use both hands for scanning and bagging). 2. Select checkstands which deliver products to the cashier on an input belt and do not require the unloading of items from a[...]

2-4 Magellan ® 9500 Scanner Installation 1. M ount the horizontal sur face of the scanner flush with the counter- top to encourage slide scanning rather than lifting. 2. P osition the centerline of the scanner read area 8 - 10 inches (20.3 - 25.4 cm) from the edge of the checkstand (cashier side). Scanner Maintenance 1. Keep scanner windows clean.[...]

Site Preparation Overview Product Reference Guide 2-5 Develop a smooth fluid motion during scanning, sharing work equally between hands. U se the entire hand for grasping and lifting items. Since the scanner reads labels on all four sides plus the top and bottom, there is no need to turn a bar code to ward either of the scanner windows. Develop eff[...]

2-6 Magellan ® 9500 Recommended Power Installation: Since the typical grocery envi- ronment includes conveyor belts and electric motors, car e should be taken to ensure that the scanner has a supply of “ clean ” power (po wer without excessive electrical noise). A wiring diagram sho ws the recommended wir- ing that will provide the scanner wit[...]

Ventilation and Spacing Product Reference Guide 2-7 Vertical Clearance: P rovision must be made to allo w adequate space above the scanner bonnet for r emoval and r eplacement of the All W eighs™ Platter (the L-shaped platter). Optimal clearance permits the platter to be grasped at its top vertic al edge and lifted for remo val without obstructio[...]

2-8 Magellan ® 9500 • A source of air that pro vides adeq uate cooling by convective air flow . If motors, conveyor belts, or other heat producing equipment are located near the scanner , forced air ventilation may be requir ed. In most installa- tions, a 30 cfm (.84 cmm) axial fan should pro vide sufficient air move- ment. If a ventilation fan [...]

Service Access Product Reference Guide 2-9 Service Access The scanner and scanner/scale have been engineered to allo w performance of all routine service and maintenance (such as “ zeroing ” and calibration) without remo ving the scanner from th e checkstand. Additionally all cable connections made at the scanner can be connected and remo ved w[...]

2-10 Magellan ® 9500 Power Installation Reference the wiring diagram in Figure 2-4 for the recommended fusing arrangement. Grounding The AC/DC P ower S upply should have an AC outlet with a clean earth ground. If you are not sure ho w to ve rify the amount of electrical noise (interference) on the power line, ask a qualified electrician to measur [...]

Checkstand Preparation Product Reference Guide 2-11 Checkstand Preparation Reference Figure 2 -5 . When per forming a first time installation into a new checkstand, verify before cutting that room will be allow ed for cabling, the AC/DC P ower Supply , and the S ensormatic ® Controller Box. When making the opening, take extra care to accurately cu[...]

2-12 Magellan ® 9500 Liquid Spills and Moisture Select a checkstand design which allo ws fluids to flow through, and directs liquids away from any electron ic equipment or storage areas. Counter Cutout The most important consideration when planning the counter opening for the scanner is the operator’ s comf ortable reaching distance. The ideal, [...]

Counter Cutout Product Reference Guide 2-13 3. Install the AC/DC P ower S upply , the Remote Scale Display cable and the interface cable(s) obser ving the following: Interface cables (and display ca ble, if applicable) should be routed away from all highly indu ctive electrical devices, like motors and conveyor belts, and even away fr om the unit?[...]

2-14 Magellan ® 9500 Figure 2-6. Typical Checkstand Design & Cutout Location Optional Item Diverter Conveyor Deadplate Scanner Bagging Area Take-Away Belt Keyboard Remote Display POS Terminal & Printer Check Writing Stand (Optional) Scan & Bag Well (Optional) 6.3" (16.0cm) Cash Drawer (Below Scanner) Flush — Correct Above Flush [...]

Counter Cutout Product Reference Guide 2-15 Refe r t o Figure 2-7 for dimensional information. Figure 2-8 and Figure 2-9 provide counter cutout details for model 850x/950x inter- changeability and minimum required counter cutout (for new 950x instal- lations) respectively . Figure 2-7. Dimensions 28.9 lb. (13.1kg) Scanner/Scale Weight 22.2 lb. (10.[...]

2-16 Magellan ® 9500 Figure 2-8. Cutout Dimensions: Reco mmended for 8500/9500 Interchangeability 20.125" (51.12cm) 0.75" (1.9cm) 18.625" (47.30cm) Rail Rail (Center Line) 11.625" (29.53cm) 0.75" (1.9cm) Max. Radius = 0.25" (0.64cm) 4x 20.125" ±0.06" (51.2 ±0.15 cm) 18.625" ± .060" (47.3 ±0.15 [...]

Counter Cutout Product Reference Guide 2-17 Figure 2-9. Cutout Dimensions: Minimum Required Counter Cutout 20.09 ± 0.06" (51.03 ± 0.15cm) 1.22" (3.1cm) 17.88 ± 0.06" (45.26 ± 0.015cm) Rail Rail (Center Line) 11.562" (29.367cm) 1.0" (2.54cm) Max. Radius = 0.25" (0.64cm) 4x 20.09" ± 0.06" (51.03 ± 0.15cm)[...]

2-18 Magellan ® 9500 Checkstand Mounting There are a number of things to take into account when installing the unit into a checkstand. Key factors are ergonomic/worker safety , loading capac- ity and stability . Consider the scanne r or scanner/scale ’ s weight when cal- culating the robustness of construction needed to support it as well as max[...]

Installation Overview Product Reference Guide 2-19 The following text describes each of these steps. Unpacking T o unpack the unit: • Inspect the package for signs of damage that may have occurr ed dur- ing shipping. If damage is found, report it to your carrier immedi- ately . • Lift out the accessory box containing the AC/DC P ower Supply , o[...]

2-20 Magellan ® 9500 Figure 2-10. Remove Protective Vinyl • P roceed to the Operational V erification instructions below . Operational Verification F ollow these steps to ensure that yo ur unit has arrived undamaged and is fully functional before installing it in the counter and connecting it to your POS system. 1. Connect the scanner and the EA[...]

Installation Overview Product Reference Guide 2-21 When power is applied to the unit, the normal indicator sequence is: • The scanner indicator (top-most, green LED) will be lit (dim) steadily . • The EAS indicator (bottom-most, tri-color LED) will flash ON/ OFF during power-up . Additionally , the 7-segment display will flash the number ‘9?[...]

2-22 Magellan ® 9500 Scanner: P ass UPC/EAN bar code labels in front of the scanner’ s win- dows. Si nce the interface cable is not yet connected to the POS ter- minal, the scanner may be limited to reading only one or two labels (see the note that follows). The scanner indicates when each label has been successfully read by flashing the gr een [...]

Installation Overview Product Reference Guide 2-23 Scale: If the Y ellow (middle, scale) LED is not lit, press the Scale Zero P ush Button momentarily . If the scale is operating correctly , the yel- low LED will illuminate and r emain on steady , and the display will show a reading of 0.00 lb (0.000 kg for metric). I f the display is blank or a is[...]

2-24 Magellan ® 9500 Diagnostic Modes T wo diagnostic modes are available which allow you to initiate scanner or scale diagnostic tests, as well as ve rify the scanner ’ s ability to read bar codes. Scanner Diagnostic Mode While in Scanner Diagnostic M ode, continuous scanning of labels is allowed, permitting the user to scan an unlimited number[...]

Installation Overview Product Reference Guide 2-25 Scale Diagnostic Mode T o enter Scale Diagnostic M ode, press the Scale Zero P ush Button for approximately four seconds. Six rapid tones will be sounded, indicating the unit is leaving normal operation and entering Scale Diagnostic M ode. The Remote D isplay will flash a ‘1’ across the display[...]

2-26 Magellan ® 9500 Figure 2-11. Cable Routing Scanner AC Power Switch (recommended) AC/DC Power Supply EAS Controller Box AC Power EAS Interface Cable Scanner Interface Cable Scale Interface Cable (Scanner/Scale) Optional Remote Scale Display Cable (optional Scanner/Scale) POS Terminal, Printer & Cash Drawer Remote Display Keyboard Alternate[...]

Remote Scale Display Placement/Installation Product Reference Guide 2-27 Figure 2-12 pro vides physical dimensions for the AC/DC Adapter (part number 8-0582). Figure 2-12. Physical Measurements: AC/DC Adapter Remote Scale Display Placement/Installation When installing the optional Remote Scale D isplay , consider both the cus- tomer’ s viewing an[...]

2-28 Magellan ® 9500 Viewing Angle The optimum viewing angle is directly facing the customer . T o ensure that the display is easily readable for the majority of your customers, the dis- play should be approximately 48 to 60” (122 to 152 cm) from the floor . Figure 2-13. Remote Scale Display NO TE Check with local W eights and Measures authoriti[...]

Remote Scale Display Placement/Installation Product Reference Guide 2-29 Placing and Installing the Remote Scale Display (Short Pedestal Base ONLY) 1. Determine where y ou want to install the Remote Scale Display based on your counter design, the viewing angle and lighting con- siderations discussed previously . Refer ence Figure 2-14 for the dis- [...]

2-30 Magellan ® 9500 Figure 2-14. Physical Measurements : Remote Display (Short Base) 6. Cut the stalk to fit y our installation (if required). 7. Route the cable through the base/stalk so that y ou can plug the con- nector into the display head. 8. Remo ve the rubber band from the connector and attach the connec- tor to the display head. 9. Slip [...]

Remote Scale Display Placement/Installation Product Reference Guide 2-31 11. Install mounting screws or bolts to complete the installation of the Remote Scale D isplay . T ake care not to pinch or pierce the interface cable while securing the Remote Scale D isplay to the checkstand. Figure 2-15. Remote Scale Display Components 48 - 60" (122 - [...]

2-32 Magellan ® 9500 Figure 2-16. Remote Scale Short Base Display Mounting Template Changing Weighing Modes Y our scanner/scale has been programmed for we ighing in either pounds or kilograms depending upon the initia l operating environment that was specified when you order ed your scanner/scale. If you need to change from pounds to kilograms or [...]

Set-Up & Installation Product Reference Guide 2-33 Set-Up & Installation These setup and installation procedures assume that y ou have already pre- pared your checkstand to r eceive the sc anner or scanner/scale. If you have not already made the counter cutout and routed po wer and interface cables, do so now as described in the previous in[...]

2-34 Magellan ® 9500 Swapping Position: EAS Single-Antenna ONLY The EAS Antenna must be located in the position needed for your instal- lation. Reference Figure 2-18 and. Locate it as described belo w: 1. Remo ve the platter (see Figure 2-22 ). 2. If the unit is a model containing a scale, and the scale assembly is determined to be in the position[...]

Set-Up & Installation Product Reference Guide 2-35 4. Disconnect the Load Cell harness. 5. M ove the Load Cell/S pider Assembly into position on the opposite side of the scanner cavity and re-install the original screws. T orque the screws evenly to 50 in-lb . Figure 2-19. Locating the EAS Single-Antenna (Left-to-Right) 6. Route the Load Cell h[...]

2-36 Magellan ® 9500 Set-up 1. Place the scanner on the checkstand next to the counter cutout. 2. Make all connections to peripheral devices, such as the Remote Scale Display (see Figure 2-15 ) and EAS Contr oller Box (see Figure 2-20 ). P ower on the EAS Controller Bo x. Figure 2-20. EAS Controller Box Connections 3. Route the cables up through t[...]

Set-Up & Installation Product Reference Guide 2-37 Figure 2-21. Connecting Cables to the Scanner/Scale POS TERMINAL REMO TE DISPLA Y A UXILLIARY POR T SCALE HOST EAS PORT PO WER Connection to this port is Optional AC Bric k Input OR Po wer off Terminal (POT) Bric k Input Scale Data (dual cable scanner/scale) Drives Remote Display · Label Data [...]

2-38 Magellan ® 9500 Installation 1. Make sure that all cables ar e firmly attached (except that the AC/ DC power supply should not be connected to the A C outlet yet). Reference Figure 2 -5 , Figure 2-20 , and Figure 2-21 . 2. Remo ve the All W eighs™ Platter to gain access to the lift handles. G rasp the platter as shown in Figure 2-22 an d g [...]

Set-Up & Installation Product Reference Guide 2-39 3. Hook the fingers of both hands in to the lift handles. The first is located along the inside of the front scanner wall, and the second is behind the scanner hood, as shown in Figure 2-23 . 4. Lower the unit into the counter opening, ensuring that none of the cables are pinched, pierced or cr[...]

2-40 Magellan ® 9500 Figure 2-23. Using the Lift Handles Marked "Lift Handle" DO NO T use the EAS Antenna to lift the unit[...]

System Power-Up Recap Product Reference Guide 2-41 System Power-Up Recap The System P ower-U p procedure may vary depending upon the require- ments of your POS system. I t is gene rally a good practice to power-down (switch off ) all equipment prior to connecting cables. Check with your System S upervisor and/or refer to your POS terminal manual fo[...]

2-42 Magellan ® 9500 6. P ower-up the scanner or scanner/scale by connecting the po wer cord to an AC po wer outlet. W ait for the unit to complete the Self test routine (10 seconds maximum). S uccessful scanner power-up is sig- nified by any or all of the following: - F acet wheel shows movement - Lasers turn on - S tatus LED(s) turn on - S peake[...]

Product Reference Guide 3-1 Chapter 3 Operation and Maintenance The information contained in this chapter describes how to operate and maintain the scanner , scale and EAS sy stem. T opics include “how to ’ s ” on scanning, EAS tag deactivation, weighing, re-zeroing the scale, r emoving the top cover and cleaning the upper and lo wer windows.[...]

3-2 Magellan ® 9500 Figure 3-1. Scan Zone Proper Scanning Technique The scanner was designed to pro vide the ultimate in ergonomic enhance- ments for P oint-Of-Sale (POS) scanni ng. T o take advantage of these advancements: P ractice the techniques below to impro ve scanning efficiency: • M ove the product across the horizontal windo w (See Figu[...]

Product Reference Guide 3-3 Deactivating Security Labels Sens or mat ic ® Ultra-Max ® , Ultra-Strip ® II and III EAS (E lectronic Arti- cle Su r veillance) tags can be detected and deactivated by the system. This is accomplished by means of a ScanMax deactivation antenna mounted under the scanner platter (single-antenna models) or both behind th[...]

3-4 Magellan ® 9500 EAS Deactivation Indicators The scanner can be programmed to beep in acknowledgement of deactiv a- tion or upon deactivation failure. Additionally , the tri-color indicator (the bottom-most LED) displays deactivation status. (F or more information about Beeper and LED indications, see the LED/Beeper Indications & Controls c[...]

Product Reference Guide 3-5 Proper Weighing Technique 1. The L-shaped All-W eighs™ platte r allows you to place items any- where on its surface, including leanin g against its vertical section, to be weighed accurately . The raised “P roduce Rail” also pro vides a convenient way to ensure items do not r est on the counter or other non-weighin[...]

3-6 Magellan ® 9500 Operational Controls The function of scanner and scale controls and indicators is listed in Appe nd ix A , LED/Beeper Indications & Controls . T urn to that appendix for full details. Operational Modes The scanner or scanner/scale features a number of modes that are impor- tant to both the user and the system support person[...]

Operational Modes Product Reference Guide 3-7 Error Reporting If a fatal error is detected during Selftest or operation, the unit will not advance to N ormal Operation M ode. Selftest diagnostics will cause the unit to sound a long, low tone and/or display an error message on the 7- segment display indicating where the failure occurr ed. These mess[...]

3-8 Magellan ® 9500 • When the scanner or scanner/scale completes its Selftest successfully , it emits a tone (when configured to do so) and enters Operating Mo de . Operating Mode Operating M ode includes Normal O peration (scanning, EAS deactivation and weighing) and Sleep M ode. These two modes are most commonly observed by the user/operator [...]

Additional Functions Product Reference Guide 3-9 Sleep Mode After the scanner has been left idle fo r a preset period of time, the laser and/or motor automatically turns off (g oes to sleep). This state is called Sleep M ode, and is indicated by a “ slow ” blink of the green light (blinking at a 2-second rate). T o wake up the unit, press anywh[...]

3-10 Magellan ® 9500 P ressing and holding the V olume/T one P ush Button for approximately eight seconds initiates a reset, which is sounded by a rapid number of beeps. If the motor had been spinni ng, the lamps will blink while the motor spins down. At that point, th e motor will spin back up and the scanner will continue to run the Selftest dia[...]

Additional Functions Product Reference Guide 3-11 Calibrating the Scale The second adjustment, calibration, defines and sets a standard r eference weight range against which all product weights ar e compared. If your scale is set for weighing in pounds, this range is 0 - 30 pounds, and, if your scale is set for weighing in kilograms, th e range is [...]

3-12 Magellan ® 9500 Operational Maintenance The scanner or scanner/scale will pro vide dependable ser vice for many years. The following maintenance pr ocedures will keep your scanner or scanner/scale operating at peak performance. Cleaning the W eigh Platter and Scan Windows . Clean the exterior sur- faces of the horizontal and vertical scan win[...]

Operational Maintenance Product Reference Guide 3-13 Vertical Scan Window Replacement The V ertical Scan Window enclosed in the All W eighs™ Platter is a replaceable part. F ollow these instruct ion s to remove a nd rep lac e th e wi n- dow: T o remove the V er tical Scan Window: 1. Gr asp the platter as shown in Figure 3-3 and gently lift it fro[...]

3-14 Magellan ® 9500 3 . T h e v e r t i c a l s c a n w i n d ow i s h e l d i n p l a c e b y t w o t a b s e a c h o n i t s t o p and bottom edges. T o remove it, car efully push out on the top as shown in Figure 3-4 and lift it out. Carefully dispose of any dam- aged glass. Figure 3-4. Vertical Scan Window Removal/Replacement 4. F ully seat t[...]

Operational Maintenance Product Reference Guide 3-15 Horizontal Scan Wind ow Replacement (WRG) W ear Resistant Glass (WR G) horizontal scan windows are r eplaceable and can be remo ved and replaced following the instructions below . 1. Remo ve the All W eighs™ Platter from the scanner as shown in Figure 3-3 . 2. T urn the platter upside down on a[...]

3-16 Magellan ® 9500 Figure 3-5. Removing/Replacing the WRG Window Slide WRG Window Out Remove V er tical Bezel[...]

Product Reference Guide 4-1 Chapter 4 Problem Isolation In the event of a suspected functional pr oblem, use the troubleshooting references pro vided in this chapter . This useful information will help you to identify and resolve the cause of the problem. The scanner/scale has a number of feat ures that indicate when a scanner , EAS deactivation sy[...]

4-2 Magellan ® 9500 Operational Tests These are the tests that run continually during N ormal Operation and Sleep M ode. F irmware checks all subsystems, accessory connections and the POS interface to verify everything is operating normally . If a problem is detected at any time, a long, low tone is sounded, an error code is shown on the 7-segment[...]

Error Codes Product Reference Guide 4-3 Error Codes If an error is detected, the scanner wi ll sound a long low tone (for one sec- ond) and alternately flash its LEDs, indicating a failure. F ollowing the long low tone, an error code will appear on the 7-segment display (r efer to Figure 4-1 ). P ressing the V olume/T one P ush button will cause th[...]

4-4 Magellan ® 9500 Error Code Probable Cause Corrective Action 0 Blinking Configuration No POS interface has been selected (Null interf ace). See the topic, Interface T ype , in Chapter 6 to select the required interface using pro- gramming bar codes. 1 Configuration Error See Chapter 6 , Pr ogramming , for details about configuring the scanner u[...]

Scale Error Reporting Product Reference Guide 4-5 Figure 4-1. 7-Segment LED Display Scale Error Reporting Scale diagnostics uses the Remote Scale Display and the Zer o Status lamp to communicate specific scale fail ures. The following chart sho ws the Remote D isplay messages, the Scale St atus lamp indication, the problem that the scale is experie[...]

4-6 Magellan ® 9500 Flowcharts The problem isolation flow charts on the following pages allow you to identify and troubleshoot problems with your system. E__3 Flash, pause, 3 blinks , long pause, repeat sequence. Scale communication lost. Internal scanner/scale prob- lem. Call technical suppor t personnel; repor t error . E__4 Flash, pause, 4 blin[...]

Flowcharts Product Reference Guide 4-7 Figure 4-2. Problem Isolation: Start START YES NO Does the scanner power-up ? YES NO Does the scanner pass Selftest ? YES NO Is the Green LED Lit ? YES NO Is the Green LED Lit ? YES NO YES Will the scanner read bar codes reliably ? YES NO Have you checked the power connections ? Check these potential problems:[...]

4-8 Magellan ® 9500 Figure 4-3. Problem Isolation: Selftest Call Tech Support Call Tech Support Error code 4. indicates a failed horizontal VLDM (laser) assembly, while 5. indicates a failed vertical VLDM. If configured to do so 1 , the scanner will remain operational with only one of these lasers until the unit can be serviced. If both lasers hav[...]

Flowcharts Product Reference Guide 4-9 Figure 4-4. Problem Isolation: Poor/No Reading DONE DONE POOR/NO READING START Have you verified that all scan windows are clean and scratch-free? YES NO Does the scanner read the bar code satisfactorily ? Verify programmable parameters using the information and programming bar codes provided in Section 6. Che[...]

4-10 Magellan ® 9500 Figure 4-5. Problem Isolation: No Transmit to POS DONE DONE NO TRANSMIT TO POS START Verify programmable parameters using the information and programming bar codes provided in Section 6. Check interface and I/F options, inactive symbologies and other configurable features. Troubleshoot the host or call Tech Support. YES NO Doe[...]

Flowcharts Product Reference Guide 4-11 Figure 4-6. Problem Isolation: Scale SCALE START View the Remote Display and/or the Yellow scale status LED for the scale error code. Reference the topic, Scale Error Reporting in Section 4 for more information. Problem is too much motion at power-up. Correct excess vibration in counter if possible. Increase [...]

4-12 Magellan ® 9500 Figure 4-7. Problem Isolation: Remote Display Call Tech Support DONE DONE REMOTE DISPLAY START YES YES YES YES NO NO NO NO Is the unit configured for a Remote Display ? Is the problem fixed ? Is the problem fixed ? Is the problem fixed ? Replace the Remote Display Use the programming bar codes in Section 6 to enable operation [...]

Flowcharts Product Reference Guide 4-13 Figure 4-8. Problem Isolation: EA S System DONE DONE NO EAS DEACTIVATION START Verify programmable parameters using the information and programming bar codes provided in Section 6. Check EAS options, and other configurable features. Call Tech Support. YES YES NO NO Do the EAS Antenna(s) deactivate labels ? Do[...]

4-14 Magellan ® 9500 NOTES[...]

Product Reference Guide 5-1 Chapter 5 Calibration A number of situations require the scale to be calibrated. They are: • at initial installation of the scanner/scale • if the scale cannot be re-zer oed • if you change the weight measur e from pounds to kilograms or vice- versa • if diagnostics indicate a calibration error • the weigh modu[...]

5-2 Magellan ® 9500 Description of Calibration Sequence The Calibration Sequence sets the scale to an accurate refer ence point for weighing. This process involves the use of a F ield Standar d W eight Set (31.5-pounds) for calibration in pounds, (18.5-kilograms) for M etric. Once calibration has been successfully completed, the scanner/scale uses[...]

Motion Test Product Reference Guide 5-3 Motion Test This test verifies that the scale will not ‘ zero ’ when the weighing surface of the scanner/scale is in motion. 1. V erify that the Y ellow LED 1 is on and the R emote Display reads 0.00 pounds or 0.000 kilograms. 2. P ress lightly on the weigh platter of the scanner/scale with one hand and a[...]

5-4 Magellan ® 9500 Preparing the Scanner/Scale for Calibration 1. Assure that the scanner/scale is st able, secure and properly installed. (Refer to Chapter 2 , Site Preparation and Installation for instructions on the proper installation of the scanner/scale). 2. P ower-up the scanner/scale. 3. Allow the unit to reach temperat ur e equilibrium f[...]

Calibrating the Scale (Pounds & Kilograms) Product Reference Guide 5-5 Figure 5-1. Calibration Access Cover 4. P ress and release the Calibration S witch to place the scanner/scale in Calibration Mode. The scanner/scale will sound a tone indicating it is in Calibration Mode. If the motor was spinning when you initi- ated Calibration M ode, the [...]

5-6 Magellan ® 9500 8. The Y ellow LED will extinguish for appro ximately 10 seconds and the Remote D isplay will alternately display and until the scale is ready to proceed. 9. If the calibration was successful, the speaker sounds a single tone, the Scale S tatus LED begins blinking again, and “End-” appears in the Remote D isplay . 10. If th[...]

Calibration Verification (U.S. Pounds) Product Reference Guide 5-7 Calibration Verification (U.S. Pounds) Once you have completed the calibrat ion sequence, you may be requir ed to perform these step-by-step verification procedures. These procedur es follow the N ational Institute of S tandards and T echnolog y Handbook-44 guidelines for grocery sc[...]

5-8 Magellan ® 9500 Shift Test The Shift T est checks to ensure that items placed anywhere on the weigh- ing surface of the scanner/scale are weighed properly . Refer to Figure 5-2 when performing this test. 1. Place and remo ve in succession, a fifteen-pound load on the center of each of the four quadrants (A, B, C, and D in F igure 5-2) of the s[...]

Calibration Verification (U.S. Pounds) Product Reference Guide 5-9 Increasing- Load Test (Phase 2) After completing the Shift T est, you must complete the Increasing Load T est using 20.0, 25.0 and 30.0 pounds of weight. 1. With the scale starting at zero, place 20.0 pounds in the center of the weighing surface and check that the display reads betw[...]

5-10 Magellan ® 9500 Decreasing-Load Test This test ensures that the scanner/scale responds pr operly when a heavy object is followed b y a significantly smaller object. 1. Place a 30.0-pound load on the scale and verify that the display shows between 29.99 and 30.01 pounds. 2. Remo ve weights to leave 20 pounds on the scale. Check that the dis- p[...]

Calibration Verification (Kilograms) Product Reference Guide 5-11 Calibration Verification (Kilograms) Once you have completed the calibrat ion sequence, you may be requir ed to perform these step-by-step verification procedures. These procedur es follow the N ational Institute of S tandards and T echnolog y Handbook-44 guidelines for grocery scale[...]

5-12 Magellan ® 9500 8. Place an additional 200 grams on the center of the weighing surface and check that the display reads 1.000 kg. 9. Increase the w eight on the scale to 7.50 kg on the center of the weighing surface and check that the display reads between 7.495 and 7.505 kg. 10. Remo ve the weights and verify that the display reads 0.000 kg.[...]

Calibration Verification (Kilograms) Product Reference Guide 5-13 Figure 5-3. European Shift Test (Metric) Increasing- Load Test (Phase 2) After completing the Shift T est, you must complete the Increasing Load T est using 10.00, 12.50 and 15 kilograms of weight. 1. Place 10.00 kilograms in the cent er of the weighing surface and check that the dis[...]

5-14 Magellan ® 9500 Blanking Test This test ensures that the scanner/scale will indicate its weighing capability has been exceeded if a weight gr eater than 0.82 over its maximum upper weight limit is placed upon the unit. 1. Place weights that total the uppe r limit plus 0.82 kilograms on the weigh platter . F or example: If the upper limit is s[...]

Calibration Verification (Kilograms) Product Reference Guide 5-15 Decreasing-Load Test This test ensures that the scanner/sc ale responds pr operly when a heavy object is followed b y a significantly smaller object. 1. Place weights that total 15.8 kilograms. 2. Remo ve weights to leave 10 kilogr ams on the scale and verify that the display shows b[...]

5-16 Magellan ® 9500 NOTES[...]

Product Reference Guide 6-1 Chapter 6 Programming Introduction to Label Programming The programming bar code labels contai ned in this manual will allow y ou to customize and configure features and settings for your scanner (scan- ner/scale). T o ensure full compatibil ity and proper function, use only the programming bar codes in this manual and o[...]

6-2 Magellan ® 9500 Integrating the Scanner With Your Host System Y our scanner MUST be equipped with the correct har dware (interface board, cable, etc.) to properly communicate with y our host system. Con- tact your dealer for information if you have questions about y our scanner’ s hardwar e compatibility . Y ou may also want to contact the d[...]

Integrating the Scanner With Your Host Sys- Product Reference Guide 6-3 • Interface Related F eatures — are the mandatory settings necessar y to allow communication with your host terminal. Examples of these settings are: RS-232 baud rate and parity . • Symbology P rogramming — gives the scanner the capability to autodiscriminate as few as [...]

6-4 Magellan ® 9500 Programming Overview The scanner’ s programmable featur e settings can be modified to accom- modate your system ’ s unique requirements. These settings can be commu- nicated to the scanner in one of three ways: 1. Commands can be sent directly from the host. A limited set of host commands are available. R efer to Appendix D[...]

Programming Overview Product Reference Guide 6-5 What Is Programming Mode? P rogramming M ode is a state in which the scanner must be placed in order to accept commands via programming bar code labels. When pro- gramming using the bar code labels in this manual, the scanner is typically placed in P rogramming Mode b y scanning the SWITCH label. Whi[...]

6-6 Magellan ® 9500 Programming Session A typical programming session is conducted as follows: 1. Scan the SWIT CH bar code to place the scanner in Programming M ode. Depending upon its current programming, the scanner may emit a beep or beeps, indicating it has read the bar code and the scanner (top) green LED will flash on and off slowly while t[...]

Programming Overview Product Reference Guide 6-7 3. Scan the SWIT CH bar code to save any new settings and exit Pr o- gramming M ode. The scanner will sound a beep and reset upon exiting P rogramming Mode, and the gr een LED will return to its usual state (on steady or off ). The scanner will exit P rogramming M ode under the following con- ditions[...]

6-8 Magellan ® 9500 Programming Sequence T o modify a scanner feature (item), the programming bar codes contained in this manual must be scanned in a given sequence depending upon the feature being programmed (as sho wn in Ta b l e 6 - 1 ). There are three possi- ble programming sequences: A. P rogramming sample A (the most commonly used format) d[...]

Programming Overview Product Reference Guide 6-9 Table 6-1. Programming Sequence 1 1 C A B 23 12 3 4 5 6 SET SWITCH ENABLE NEW FEA TURE ENABLE NEW FEA TURE USING THE FOLLO WING SETTINGS... SWITCH SWITCH SWITCH 0 8 ITEM T A G ITEM V ALUE END/RESET 0 ONE B AR CODE CONT AINS SWITCH + ITEM T A G + ITEM V ALUE + SWITCH[...]

6-10 Magellan ® 9500 LED and Beeper Indicators The scanner pro vides a set of indicators that verify/announce the various scanner functions. If You Make a Mistake... If, during a pr ogramming session, yo u find that you are unsure of the scanner’ s settings or wish to reset the scanner ’ s configuration, use the Return to F actor y Settings la[...]

If You Make a Mistake... Product Reference Guide 6-11 Test Mode U se this feature to place the scanner into a testing, or “ demo ” mode. This special mode disables the scanner interface, meaning that bar code data is not sent out to the host via the scanne r interface. This allows the bar code to be scanned continuously without requiring a resp[...]

6-12 Magellan ® 9500 General Scanner and Scale Features Double Read Timeout The Double R ead T imeout feature sets a time limit that determines how much time must pass before reading the same label again (e.g. two identi- cal items in succession). T o set the Double Read T imeout: 1. Scan the SWIT CH bar code. 2. Scan your selection from the bar c[...]

General Scanner and Scale Features Product Reference Guide 6-13 Double Read Timeout — continued Remember to co ver any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code y ou intend to scan. DOUBLE READ TIMEOUT = 800ms DOUBLE READ TIMEOUT = 1 SECOND[...]

6-14 Magellan ® 9500 Laser Timeout The laser timeout feature sets the ti me for switching the visible laser diodes (VLDs) off if the scanner is idle. Using this featur e can prolong the life of the VLDs. T o set the Laser T imeout: 1. Scan the SWIT CH bar code. 2. Scan your selection from the bar codes below . Y ou ’ll need to cover any unused b[...]

General Scanner and Scale Features Product Reference Guide 6-15 Laser Timeout — continued Remember to co ver any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code y ou intend to scan. LASER TIMEOUT = 10 MINUTES LASER TIMEOUT = 15 MINUTES[...]

6-16 Magellan ® 9500 Motor Timeout The M otor T imeout feature sets the time for automatically switching the motor off when the scanner is not in use. T o set the Motor T imeout: 1. Scan the SWIT CH bar code. 2. Scan your selection from the bar codes below . Y ou ’ll need to cover any unused bar codes on this and th e facing page to ensure that [...]

General Scanner and Scale Features Product Reference Guide 6-17 Motor Timeout — continued Remember to co ver any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code y ou intend to scan. MO TOR TIMEOUT = 10 MINUTES MO TOR TIMEOUT = 15 MINUTES[...]

6-18 Magellan ® 9500 Motor Timeout — continued Remember to co ver any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code y ou intend to scan. MO TOR TIMEOUT = 30 MINUTES MO TOR TIMEOUT = 60 MINUTES[...]

General Scanner and Scale Features Product Reference Guide 6-19 Green LED Idle State This feature specifies the state of the green scanner LED when the scanner is idle and ready to read a label. O ptions are: •O f f •O n d i m T o set the LED Idle S tate: 1. Scan your selection from the bar codes below . Y ou ’ll need to cover any unused bar [...]

6-20 Magellan ® 9500 Scanner Button Options Configure the scanner volume button to one of the follo wing modes of operation: • Enable all functions: V olume, tone, diagnostics and r eset. • Enable only volume, tone and reset. • Enable reset only . • Disable all button functions T o set the desired Scanner Button Option: 1. Scan the SWIT CH[...]

General Scanner and Scale Features Product Reference Guide 6-21 Scanner Button Options — continued Remember to co ver any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code y ou intend to scan. SCANNER BUTT ON OPTION = ENABLE RESET ONL Y SCANNER BUTT ON OPTION = DISABLE ALL BUTT ON FUNCTIONS[...]

6-22 Magellan ® 9500 Power-up Beep Control S pecifies the type of audible indication that is made when entering scan- ner-active mode on pow er-up. Choices are: • N o beep • One beep • Three beeps T o set the P ower-up Beep: 1. Scan the SWIT CH bar code. 2. Scan your selection from the three bar codes belo w . Y ou ’ll need to cover any un[...]

General Scanner and Scale Features Product Reference Guide 6-23 Power-up Beep Control — continued Remember to co ver any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code y ou intend to scan. POWER-UP BEEP = ONE BEEP POWER-UP BEEP = THREE BEEPS[...]

6-24 Magellan ® 9500 Good Read Beep Control This feature enables/disables scanner b eep upon successfully decoding of a label. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan your selection from the two bar codes below . Y ou ’ll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the [...]

General Scanner and Scale Features Product Reference Guide 6-25 Good Read Beep Frequency Ad j u s ts t h e sc a n n e r’ s g o o d r e a d b e e p t o s o u n d a t lo w , m e d iu m , o r hi g h f re - quency (controls the beeper ’ s pitch/tone). • Low = 660 Hz • M edium = 860 Hz • High = 1050 Hz T o set the Good Read Beep F requency: 1.[...]

6-26 Magellan ® 9500 Good Read Beep Frequency — continued Remember to co ver any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code y ou intend to scan. GOOD READ BEEP FREQUENCY = MEDIUM GOOD READ BEEP FREQUENCY = HIGH[...]

General Scanner and Scale Features Product Reference Guide 6-27 Good Read Beep Length S pecifies the duration of a good read beep. T o set the good read beep length: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET GOOD READ BEEP LENGTH . Y ou ’ll need to cover any unused bar codes on this and the facing page to ensur e that the scanner re[...]

6-28 Magellan ® 9500 Good Read Beep Volume Selects the beeper volume upon a good r ead beep. There ar e five selectable volumes, with each volume increment adding approximately five decibels to the previous level: • 0 = Lowest V olume •1 = M e d i u m - L o w V o l u m e •2 = M e d i u m V o l u m e • 3 = Medium-H igh V olume •4 = H i g [...]

General Scanner and Scale Features Product Reference Guide 6-29 Good Read Beep Volume — continued Remember to co ver any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code y ou intend to scan. GOOD READ BEEP V OLUME = MEDIUM LOW GOOD READ BEEP V OLUME = MEDIUM[...]

6-30 Magellan ® 9500 Good Read Beep Volume — continued Remember to co ver any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code y ou intend to scan. GOOD READ BEEP V OLUME = MEDIUM HIGH GOOD READ BEEP V OLUME = HIGHEST[...]

General Scanner and Scale Features Product Reference Guide 6-31 Good Read When to Indicate This feature specifies when the scanner will pro vide indication (beep and/ or flash its green LED) upon successfully reading a bar code. • Good Read = I ndicate after decode • Good Read = I ndicate after transmit • Good Read = I ndicate after CT S goes[...]

6-32 Magellan ® 9500 Good Read When to Indicate — continued Remember to co ver any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code y ou intend to scan. GOOD READ = INDICA TE AFTER TRANSMIT GOOD READ = INDICA TE AFTER CTS GOES INACTIVE, THEN A CTIVE (RS-232 ONL Y)[...]

General Scanner and Scale Features Product Reference Guide 6-33 Scale Enable U se this feature to enable or disable scale operation. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan your selection from the two bar codes below . Y ou ’ll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only[...]

6-34 Magellan ® 9500 Scale Country Mode When a weight is presented, the sca nner/scale will apply the country-spe- cific weighing rules specified via this feature. SCALE COUNTR Y MODE = U .S.A. SCALE COUNTR Y MODE = U .K. NO TE Scale Country Mode applies only when a scale is enabled. RS-232 SASI scale interface supports only U.S.A. mode.[...]

General Scanner and Scale Features Product Reference Guide 6-35 Scale Country Mode — continued Remember to co ver any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code y ou intend to scan. SCALE COUNTR Y MODE = A USTRALIA[...]

6-36 Magellan ® 9500 Scale Enforced Zero Return This feature enables/disables the enforced zer o return of the scale. Three settings are available for this featur e: •D i s a b l e • Scale M ust Return to Zero W eight Within F our Minutes — Scale will require r e-zeroing if a non-zero weight is left on for more than 4 minutes • Scale M ust[...]

General Scanner and Scale Features Product Reference Guide 6-37 Scale Enforced Zero Return — continued Remember to co ver any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code y ou intend to scan. SCALE ENFORCED ZERO RETURN = SCALE MUST RETURN T O ZERO WEIGHT WITHIN 4 MINUTES SCALE ENFORCED ZERO RETUR[...]

6-38 Magellan ® 9500 Scale Interface Type U se this feature to select the scale interface type. Choices are: • N o Scale Interface • RS-232 — SASI • RS-232 — ICL T o set the Scale Interface T ype: 1. Scan the SWIT CH bar code. 2. Scan your selection from the bar codes below . Y ou ’ll need to cover any unused bar codes on this and th e[...]

General Scanner and Scale Features Product Reference Guide 6-39 Scale Interface Type — continued Remember to co ver any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code y ou intend to scan. SCALE INTERF ACE TYPE = RS-232 — ICL[...]

6-40 Magellan ® 9500 Scale Motion Level Filter In environments wher e checkstands gene rate excessive vibration, the scale can be set to filter a certain amount of the motion with regard to its oper- ation. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan your selection from the bar codes below . Y ou ’ll need to cover any unused bar [...]

General Scanner and Scale Features Product Reference Guide 6-41 Scale Motion Level Filter — continued Remember to co ver any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code y ou intend to scan. SCALE MO TION LEVEL FIL TER = MEDIUM HIGH SCALE MO TION LEVEL FIL TER = HIGH[...]

6-42 Magellan ® 9500 Scale LED Enable This feature enables/disables Scale LED (Y ellow LED) operation. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan your selection from the two bar codes below . Y ou ’ll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to s[...]

General Scanner and Scale Features Product Reference Guide 6-43 Remote Display — Enable/Disable The scanner-scale can be configured to operate with or without a Remote Dis pl ay . REMO TE DISPLA Y = DISABLE REMO TE DISPLA Y = ENABLE NO TE Recalibration/recertification may be required when adding a Remote Display . Consult your local W eights and [...]

6-44 Magellan ® 9500 Aux Port Mode Selects the usage for the scanner ’ s optional auxilliar y port. The choices listed below ar e mutually exclusive (only one option can be active at a time). • Disabled — P or t is inactive • External Handheld I nput — Supports Datalogic ® handheld scan- ners (QuickScan 1000, QuickScan 6000, P owerScan)[...]

General Scanner and Scale Features Product Reference Guide 6-45 Aux Port Mode — continued Remember to co ver any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code y ou intend to scan. A UX PORT MODE = EXTERNAL HANDHELD INPUT A UX PORT MODE = PIR[...]

6-46 Magellan ® 9500 Laser Failure Mode This configuration item selects whethe r the scanner should continue oper- ating if only one laser is functional . (The scanner has two lasers: One for the horizontal window , and one for the vertical window .) Options for this feature are: • Single Laser F ailure OK — The scanner can still operate even [...]

General Scanner and Scale Features Product Reference Guide 6-47 Productivity Index Reporting (PIR)/Cashier Training (CT) When PIR/CT is enabled, label qualit y data is appended to decoded data before being presented to the POS. The P IR feature allows the scanner to pro vide information to an external co mputer indicating how easy the label was to [...]

6-48 Magellan ® 9500 EAS Features EAS Mode This controls the mode of operation for interfacing with the Sensor- matic ® ScanMax P ro TM EAS device. Choices are: • Disabled = EAS deactivation turned off . • Coupled Mode = EAS tag is deactiv ated only upon successful scan- ning of an item ’ s barcode or via manual push button. • Decoupled M[...]

EAS Features Product Reference Guide 6-49 EAS Mode — continued Remember to co ver any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code y ou intend to scan. EAS MODE = DISABLE EAS MODE = COUPLED MODE[...]

6-50 Magellan ® 9500 EAS Mode — continued Remember to co ver any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code y ou intend to scan. EAS MODE = DECOUPLED MODE EAS MODE = HYBRID MODE[...]

EAS Features Product Reference Guide 6-51 EAS Beep Duration Sets the duration of the EAS successf ul deactivation beep , specified in 10ms increments. The beep only occu rs if EAS mode is not disabled. T o set the EAS Beep Duration: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET EAS BEEP DURA TION below . Y ou ’ll need to cover any unuse[...]

6-52 Magellan ® 9500 EAS Retry Count This feature sets the number of times the deactivation sequence (defined by the feature, “EAS Deactivation D uration — Retry ”) is restarted after a failed deactivation attempt. T o set the EAS Retry Count: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET EAS RETR Y COUNT below . Y ou ’ll need to[...]

EAS Features Product Reference Guide 6-53 Manual EAS Deactivation Push Button This feature is for use in Coupled M ode 1 . When it is enabled, EAS deacti- vation can be manually initiated by placing the item with the EAS tag downstream 2 of the horiz ontal scan window and pushing the Manual EAS Deactivation P ush Button. Options are: • DISABLE ?[...]

6-54 Magellan ® 9500 Manual EAS Deactivation Push Button — continued Remember to co ver any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code y ou intend to scan. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan your selection from the bar codes below . Y ou ’ll need to cover any unused [...]

EAS Features Product Reference Guide 6-55 Manual EAS Deactivation Push Button — continued Remember to co ver any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code y ou intend to scan. MANU AL EAS DEACTIV A TON PUSH BUTT ON = ENABLE ONL Y WHEN SCANNER ENABLED[...]

6-56 Magellan ® 9500 EAS Deactivation Duration — Coupled S pecifies the amount of time EAS deac tivation is operative once the func- tion has been initiated following a bar code read. T o set the EAS Deactivation Duration — Coupled: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET EAS DEACTIV A TION DURA TION — COUPLED below . Y ou ?[...]

EAS Features Product Reference Guide 6-57 EAS Deactivation Duration — Retry S pecifies the amount of time EAS deac tivation is operative once the func- tion has been initiated following EAS tag detection (prior to bar code read ).. T o set the EAS Deactivation Duration — Retry: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET EAS DEACTIV[...]

6-58 Magellan ® 9500 EAS Deactivation Duration — Manual S pecifies the amount of time EAS deac tivation is operative upon pushing the Manual EAS Deactivation P ush Button. T o set the EAS Deactivation Duration — Manual: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET EAS DEACTIV A TION DURA TION — MANUAL belo w . Y ou ’ll need to c[...]

Interface Related Features Product Reference Guide 6-59 Interface Related Features Interface Type S pecifies the current scanner interface. Selections are: INTERF A CE TYPE INTERF A CE IDENTIFICA TION NUMBER a a. T o access a scanner’ s interface identification n umber, place the scanner in Scanner Diagnostic Mode and view the 7-segment FR U disp[...]

6-60 Magellan ® 9500 Interface Type — continued T o select the desired interface: 1. Disconnect current interface cable(s) if curr ently connected. 2. Scan the SWIT CH bar code 3. Scan the bar code representing the appropriate interface located on the following pages. Y ou ’ll need to co ver any unused bar codes adja- cent to and on any facing[...]

Interface Related Features Product Reference Guide 6-61 RS-232 Interface Selection Remember to co ver any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code y ou intend to scan. INTERF ACE TYPE = RS-232 ST AND ARD CA UTION Great care should be taken to select the correct interface type, since you can cau[...]

6-62 Magellan ® 9500 RS-232 Wincor-Nixdorf Interface Selection Remember to co ver any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code y ou intend to scan. INTERF ACE TYPE = RS-232 WINCOR-NIXDORF CA UTION Great care should be taken to select the correct interface type, since you can cause damage to th[...]

Interface Related Features Product Reference Guide 6-63 RS-232 Single Cable Interface Selection Remember to co ver any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code y ou intend to scan. INTERF ACE TYPE = RS-232 SINGLE CABLE CA UTION Great care should be taken to select the correct interface type, si[...]

6-64 Magellan ® 9500 IBM Port 17 Interface Selection Remember to co ver any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code y ou intend to scan. INTERF ACE TYPE = IBM POR T 17 CA UTION Great care should be taken to select the correct interface type, since you can cause damage to the scanner and/or PO[...]

Interface Related Features Product Reference Guide 6-65 IBM USB Interface Selection Remember to co ver any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code y ou intend to scan. INTERF ACE TYPE = IBM USB CA UTION Great care should be taken to select the correct interface type, since you can cause damage[...]

6-66 Magellan ® 9500 Maximum Host-Transmitted Message Length S pecifies the maximum number of data characters allowed in messages transmitted to the host. T o set the Maximum Host-T ransmitted M essage Length: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET MAXIMUM HOST -TRANSMITTED MES- SAGE LENGTH below . Y ou ’ll need to cover any unu[...]

Interface Related Features Product Reference Guide 6-67 Number of Host Transmission Buffers S pecifies the number of host transm ission(s) that may be buffered. By buffering data from a bar code, the scanner can continue to read a new bar code while the old one is being transmitted to the host. Selecting BUFF- ERS = 1 means that the first bar code [...]

6-68 Magellan ® 9500 Global Prefix This feature applies to RS-232 interfaces (S tandard, Wincor-N ixdorf, and Single Cable). I t specifies the prefix that is added to beginning of label transmission. T o specify the Global P refix Character(s): 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET GLOBAL PREFIX below . Y ou ’ll need to cover a[...]

Interface Related Features Product Reference Guide 6-69 Global Prefix — continued Remember to co ver any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code y ou intend to scan. SET GLOBAL PREFIX TERMINA TE SEQUENCE[...]

6-70 Magellan ® 9500 Global Suffix This feature applies to RS-232 interfaces (S tandard, Wincor-N ixdorf, and Single Cable). I t specifies the suffix that is added to end of a label trans- mission. Three standar d options are available below . Contact your dealer for other alternate settings for this feature. • N o Global Suffix • CR — Carri[...]

Interface Related Features Product Reference Guide 6-71 Global Suffix — continued Remember to co ver any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code y ou intend to scan. GLOBAL SUFFIX = CR GLOBAL SUFFIX = CR LF[...]

6-72 Magellan ® 9500 IBM Features IBM Interface Options IBM interfaces offer specific control over interaction with certain devices. Options for this feature ar e as follows: • FULL host interface support — Accepts scanner and scale config- uration host commands. • Ignore host interface configuration of scanner and scale — Ignores all scan[...]

IBM Features Product Reference Guide 6-73 IBM Scale Address S pecifies IBM scale address for IBM P ort 17. The following three addresses are av ailable: •6 A •6 B •6 E T o set the IBM Scale Address: 1. Scan the SWIT CH bar code. 2. Scan the bar code below or from the following page that r epresents the desired scale address designation. 3. Co[...]

6-74 Magellan ® 9500 IBM Scale Address — continued Remember to co ver any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code y ou intend to scan. IBM SCALE ADDRESS = 6B IBM SCALE ADDRESS = 6E[...]

IBM Features Product Reference Guide 6-75 IBM Transmit Labels in Code 39 Format This feature enables/disables scanner's ability to set a symbology identifier for a specified label to Code 39 before transmitting that label data to an IBM host. This applies to: Code 128, Code 93 and Codabar for IBM P ort 5B; Code 93 and Codabar for IBM P ort 9B;[...]

6-76 Magellan ® 9500 IBM USB Interface Options The IBM-USB interface offers specific control over interaction with cer- tain devices. Options for this feature are as follo ws: • FULL host interface support — Accepts scanner and scale config- uration host commands. • Compatible with Magellan SL host interface support — U ses Magellan SL hos[...]

IBM Features Product Reference Guide 6-77 IBM USB Interface Options — continued Remember to co ver any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code y ou intend to scan. IBM USB INTERF ACE OPTION = COMP A TIBLE W/MA GELLAN SL HOST I/F SUP- PORT IBM USB INTERF ACE OPTION = IGNORE HOST I/F CONFIG OF[...]

6-78 Magellan ® 9500 IBM USB Scanner Device Type The IBM-USB protocol allows for the sc anner to be identified as one of two different types of barcode scanne rs. Depending on what other scan- ners you may already have connected to a USB POS, y ou may need to change this setting to enable all scanners to communicate. Options are: • T able T op S[...]

RS-232 Features Product Reference Guide 6-79 RS-232 Features RS-232 Baud Rate This feature selects the baud rate requir ed for sending and receiving data. T o specify the RS-232 Baud Rate: 1. Scan the SWIT CH bar code. 2. Scan the desired baud rate from the bar codes belo w and on the immediately following pages. Y ou ’ll need to co ver any unuse[...]

6-80 Magellan ® 9500 RS-232 Baud Rate — continued Remember to co ver any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code y ou intend to scan. RS-232 BA UD RA TE = 4800 RS-232 BA UD RA TE = 9600[...]

RS-232 Features Product Reference Guide 6-81 RS-232 Baud Rate — continued Remember to co ver any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code y ou intend to scan. RS-232 BA UD RA TE = 19200 RS-232 BA UD RA TE = 38400[...]

6-82 Magellan ® 9500 RS-232 Baud Rate — continued Remember to co ver any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code y ou intend to scan. RS-232 BA UD RA TE = 57600 RS-232 BA UD RA TE = 115200[...]

RS-232 Features Product Reference Guide 6-83 RS-232 Number of Data Bits S pecifies number of data bits required for sending and receiving data. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code below repr esenting the desired Data Bit setting. Y ou ’ll need to cov er any unused bar codes on this and the facing page to ensur[...]

6-84 Magellan ® 9500 RS-232 Number of Stop Bits S pecifies number of stop bits required for sending and receiving data. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code below repr esenting the desired S top Bit setting. Y ou ’ll need to cov er any unused bar codes on this and the facing page to ensure that the scanner rea[...]

RS-232 Features Product Reference Guide 6-85 RS-232 Parity S pecifies parity required for sending and receiving data. Options for this setting are: • RS-232 P ARITY = NONE • RS-232 P ARITY = EVEN • RS-232 P ARITY = ODD T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code below or on the follo wing pages representing the de[...]

6-86 Magellan ® 9500 RS-232 Parity — continued Remember to co ver any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code y ou intend to scan. RS-232 P ARITY = EVEN RS-232 P ARITY = ODD[...]

RS-232 Features Product Reference Guide 6-87 RS-232 Hardware Control Enables/disables use of the RS-232 CTS signal for flo w control and/or scan control. Options are: • Disable — The scanner transmits to the host regar dless of any activ- ity on the CTS line. • Enable CTS F low Control — The CT S signal controls transmission of data to the [...]

6-88 Magellan ® 9500 RS-232 Hardware Control — continued Remember to co ver any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code y ou intend to scan. RS-232 HARD W ARE CONTROL = ENABLE CTS FLO W CONTROL RS-232 HARD W ARE CONTROL = ENABLE CTS SCAN CONTROL[...]

RS-232 Features Product Reference Guide 6-89 RS-232 Intercharacter Delay S pecifies delay between the end of one character and the beginning of the next in 10-millisecond increments. T o set the RS-232 Intercharacter Delay: 1. Scan the SWIT CH bar code. 2. Scan the bar code below , SET RS-232 INTERCHARACTER DELA Y . Y ou ’ll need to cov er any un[...]

6-90 Magellan ® 9500 RS-232 Software Flow Control Enables/disables RS-232 Flo w Control using XON/ X OFF characters. . T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan either the enable or disable bar code below . Y ou ’ll need to cov er any unused bar codes on this and th e facing page to ensure that the scanner reads only the bar co[...]

RS-232 Features Product Reference Guide 6-91 RS-232 Host Echo When enabled, this feature passes all data through the scanner to the host as it comes in. This feature is used for applications where “ daisy chaining” of RS-232 devices onto the same cable is necessary . If, for example, one of the devices in the chain is a terminal where someone i[...]

6-92 Magellan ® 9500 RS-232 Host Echo Quiet Interval This setting specifies the time interval of RS-232 channel inactivity which must transpire before the scanner will br eak the host echo loop to transmit the bar code data that has just been scanned to the host. • 0 - 100 = T ime in 10-millisecond increments. T o set the Host Echo Quiet Interva[...]

RS-232 Features Product Reference Guide 6-93 RS-232 Ignore Host Commands When set to ignore host commands, the scanner will ignore all host com- mands except for the minimum set necessary to keep the interface active, transmit labels, and transmit scale in formation. F or normal operation of the interface, disable this feature. T o set this feature[...]

6-94 Magellan ® 9500 RS-232 TTL S pecifies whether RS-232 interface provides TTL levels on the output pins TxD and R TS. Choices are: • N ormal RS-232 levels •T T L l e v e l s T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code below which r epresents the desired setting for this feature. Y ou ’ll need to co ver any unu[...]

RS-232 Features Product Reference Guide 6-95 RS-232 TTL Invert Enables/disables inversion of TTL. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code below which r epresents the desired setting for this feature. Y ou ’ll need to co ver any unused bar codes on this and the facing page to ensure that the scanner reads only the [...]

6-96 Magellan ® 9500 RS-232 Beep on ASCII BEL Enables/disables ability of scanner to beep (sound a good read tone) on receiving an ASCII BEL (07 hex). •D i s a b l e • Enable T o enable/disable this feature: 1. Scan the SWIT CH bar code. 2. Scan either the enable or disable bar code below . Y ou ’ll need to cov er any unused bar codes on thi[...]

RS-232 Features Product Reference Guide 6-97 RS-232 Beep After Weigh Enables/disables the ability of the sc anner to beep after weight data is transmitted to the host. Scale interfaces that support this item are: RS-232 ICL, RS-232 SASI, and RS-232 Single Cable. T o enable/disable the Beep After W eigh feature: 1. Scan the SWIT CH bar code. 2. Scan[...]

6-98 Magellan ® 9500 RS-232 Beep on Not on File Select for the host to beep (or not) when a not-on-file condition is detected by the host. This feature is also applicable to single cable RS-232. RS-232 BEEP ON NO T ON FILE = DISABLE RS-232 BEEP ON NO T ON FILE = ENABLE[...]

RS-232 Features Product Reference Guide 6-99 RS-232 ACK NAK Enable This enables/disables the ability of the scanner to support the RS-232 ACK/NAK protocol. When configur ed, the scanner and/or host sends an “ ACK” when it receiv es data properly , and sends “NAK” when the data is in error . Selections for this option ar e: •D i s a b l e [...]

6-100 Magellan ® 9500 RS-232 ACK NAK Enable — continued Remember to co ver any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code y ou intend to scan. RS-232 ACK/NAK = HOST A CKNOWLEDGEMENT RS-232 AC K/NAK = LABEL & HOST[...]

RS-232 Features Product Reference Guide 6-101 RS-232 ACK Character This feature specifies which ASCII char acter will be used as an ACK char- acter . T o specify the RS-232 ACK Character: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET RS-232 ACK CHARACTER below . Y ou ’ll need to cover any unused bar codes on this and the facing page to [...]

6-102 Magellan ® 9500 RS-232 NAK Character This feature specifies which ASCII ch aracter will be used as a NAK char- acter . T o specify the RS-232 NAK Character: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET RS-232 NAK CHARACTER below . Y ou ’ll need to cover any unused bar codes on this and the facing page to ensure the scanner reads[...]

RS-232 Features Product Reference Guide 6-103 RS-232 Retry on ACK NAK Timeout This option specifies the action scanner performs on expiration of the RS- 232 ACK NAK T imeout V alue . T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan either the enable or disable bar code below . Y ou ’ll need to cover any unused bar codes on this and th [...]

6-104 Magellan ® 9500 RS-232 ACK NAK Timeout Value This item specifies the time the sca nner will wait for an ACK character from the host following a label transmission. • 0 = Infinite timeout • 1 - 75 = T imeout in 200-millisecond increments T o set the ACK NAK T imeout V alue: 1. Scan the SWIT CH bar code. 2. Scan the bar code below , SET RS[...]

RS-232 Features Product Reference Guide 6-105 RS-232 ACK NAK Retry Count This feature sets the number of times for the scanner to retry a label trans- mission under a retry condition. T o set the RS-232 ACK NAK Retry Count: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET RS-232 ACK NAK RETR Y COUNT below . Y ou ’ll need to cov er any unus[...]

6-106 Magellan ® 9500 RS-232 ACK NAK Error Handling This item specifies the method the scanner will use to handle errors detected while waiting to receive the A CK character from the host. Errors include unrecognized host commands and communication errors such as parity or framing errors. • Ignore Err ors (recommended setting) • Assume ACK (ri[...]

RS-232 Features Product Reference Guide 6-107 RS-232 ACK NAK Error Handling — continued Remember to co ver any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code y ou intend to scan. RS-232 ACK NAK ERR OR HANDLING = ASSUME ACK RS-232 ACK NAK ERR OR HANDLING = ASSUME NAK[...]

6-108 Magellan ® 9500 RS-232 Label ID Control This feature specifies whether or not Label IDs are transmitted to the host and if so, whether to attach them as a prefix or suffix. RS-232 LABEL ID CONTROL = DISABLE RS-232 LABEL ID CONTROL = ENABLE AS PREFIX[...]

RS-232 Features Product Reference Guide 6-109 RS-232 Label ID Control — continued Remember to co ver any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code y ou intend to scan. RS-232 LABEL ID CONTROL = ENABLE AS SUFFIX[...]

6-110 Magellan ® 9500 Single Cable RS-232 Options The RS-232 Single Cable interface shares some configuration options with other RS-232 interfaces. Rather th an repeat them in this chapter as Single Cable options, please find them refer enced as follows: • RS-232 Baud Rate on page 79 • RS-232 Number of Data Bits on page 83 • RS-232 Number of[...]

Single Cable RS-232 Options Product Reference Guide 6-111 Single Cable RS-232 Scanner Only Protocol This sets the type of interface protocol that will be used in Single Cable RS-232. Options are: • Scanner/scale RS-232 protocol • Scanner only RS-232 protocol T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code below repr ese[...]

6-112 Magellan ® 9500 Single Cable RS-232 RTS CTS Selection S pecifies how R TS and CTS are used to contr ol the data flow . R TS is con- trolled by the Scanner and can be cont inuously held high/low , or can be asserted during label transmission. Th e scanner looks at CTS, as the con- figuration values state, to determine when to send label data.[...]

Single Cable RS-232 Options Product Reference Guide 6-113 Single Cable RS-232 RTS CTS Selection — continued Remember to co ver any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code y ou intend to scan. RTS CTS SELECTION = OPTION 2 RTS CTS SELECTION = OPTION 3[...]

6-114 Magellan ® 9500 Single Cable RS-232 RTS CTS Selection — continued Remember to co ver any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code y ou intend to scan. RTS CTS SELECTION = OPTION 4 RTS CTS SELECTION = OPTION 5[...]

Single Cable RS-232 Options Product Reference Guide 6-115 Single Cable RS-232 Use BCC Enables/disables the ability of the scanner to use BCC. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan either the enable or disable bar code below . Y ou ’ll need to cover any unused bar codes on this and th e facing page to ensure that the scanner [...]

6-116 Magellan ® 9500 Single Cable RS-232 Use ACK/NAK Enables/disables the ability of the scanner to use ACK/NAK. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan either the enable or disable bar code below . Y ou ’ll need to cov er any unused bar codes on this and th e facing page to ensure that the scanner reads only the bar code yo[...]

Single Cable RS-232 Options Product Reference Guide 6-117 Single Cable RS-232 Use STX Enables/disables the ability of the scanner to use STX. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan either the enable or disable bar code below . Y ou ’ll need to cover any unused bar codes on this and th e facing page to ensure that the scanner [...]

6-118 Magellan ® 9500 Set Single Cable RS-232 STX Character This feature selects the STX character . T o specify the ST X Character: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET SINGLE CABLE RS-232 STX CHARACTER below . Y ou ’ll need to cover any unused bar codes on this and the fac- ing page to ensure the scanner reads only the bar c[...]

Single Cable RS-232 Options Product Reference Guide 6-119 Single Cable RS-232 Use ETX Enables/disables the ability of the scanner to use ETX. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan either the enable or disable bar code below . Y ou ’ll need to cover any unused bar codes on this and th e facing page to ensure that the scanner [...]

6-120 Magellan ® 9500 Set Single Cable RS-232 ETX Character Allows selection of the ETX character . T o specify the ET X Character: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET SINGLE CABLE RS-232 ETX CHARACTER below . Y ou ’ll need to cover any unused bar codes on this and the fac- ing page to ensure the scanner reads only the bar co[...]

Symbology Programming Product Reference Guide 6-121 Symbology Programming UPC-A Enable Enables/disables the ability of the scanner to decode UPC-A labels. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan either the enable or disable bar code below . Y ou ’ll need to cover any unused bar codes on this and th e facing page to ensure that[...]

6-122 Magellan ® 9500 UPC-A Number System Character Transmission Enables/disables transmission of a UPC-A number system character . T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan either the enable or disable bar code below . Y ou ’ll need to cov er any unused bar codes on this and th e facing page to ensure that the scanner reads on[...]

UPC-A Enable Product Reference Guide 6-123 UPC-A Check Character Transmission Enables/disables transmission of a UPC-A check character . T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan either the enable or disable bar code below . Y ou ’ll need to cover any unused bar codes on this and th e facing page to ensure that the scanner reads[...]

6-124 Magellan ® 9500 Expand UPC-A to EAN-13 Enables/disables expansion of UPC-A labels to EAN/JAN-13. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan either the enable or disable bar code below . Y ou ’ll need to cov er any unused bar codes on this and th e facing page to ensure that the scanner reads only the bar code you intend to[...]

UPC-A Enable Product Reference Guide 6-125 UPC/EAN AIM ID This feature enables/disables transmission of the UPC/EAN AIM symbol- ogy identifier . T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan your selection from the bar codes below . Y ou ’ll need to cover any unused bar codes on this and th e facing page to ensure that the scanner r[...]

6-126 Magellan ® 9500 UPC-A Label ID This feature specifies a UPC-A label ID to be added to bar code data. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET UPC-A LABEL ID below . Y ou ’ll need to cover any unused bar codes on this and the facing page to ensur e the scanner reads only the bar code you intend to scan. [...]

UPC-A Enable Product Reference Guide 6-127 UPC-A 2-Digit Supplemental Label ID This feature specifies a UPC-A 2-Digit S upplemental label ID to be added to bar code data. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET UPC-A 2-DIGIT SUPPLEMENT AL LABEL ID below . Y ou ’ll need to cover any unused bar codes on this an[...]

6-128 Magellan ® 9500 UPC-A 5-Digit Supplemental Label ID This feature specifies a UPC-A 5-Digit S upplemental label ID to be added to bar code data. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET UPC-A 5-DIGIT SUPPLEMENT AL LABEL ID below . Y ou ’ll need to cover any unused bar codes on this and the facing page to[...]

UPC-A Enable Product Reference Guide 6-129 UPC-A 128 Supplemental Label ID This feature specifies a UPC-A 128 S upplemental label ID to be added to bar code data. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET UPC-A 128 SUPPLEMENT AL LABEL ID below . Y ou ’ll need to cov er any unused bar codes on this and the fac- [...]

6-130 Magellan ® 9500 UPC-E Enable Enables/disables the ability of the scanner to decode UPC-E labels. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan either the enable or disable bar code below . Y ou ’ll need to cov er any unused bar codes on this and th e facing page to ensure that the scanner reads only the bar code you intend to[...]

UPC-E Enable Product Reference Guide 6-131 UPC-E Number System Character Transmission Enables/disables transmission of a UPC-E number system character . T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan either the enable or disable bar code below . Y ou ’ll need to cover any unused bar codes on this and th e facing page to ensure that t[...]

6-132 Magellan ® 9500 UPC-E Check Character Transmission Enables/disables transmission of a UPC-E check character . T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan either the enable or disable bar code below . Y ou ’ll need to cov er any unused bar codes on this and th e facing page to ensure that the scanner reads only the bar code [...]

UPC-E Enable Product Reference Guide 6-133 Expand UPC-E to UPC-A Enables/disables expansion of UPC-E labels to UPC-A. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan either the enable or disable bar code below . Y ou ’ll need to cover any unused bar codes on this and th e facing page to ensure that the scanner reads only the bar code [...]

6-134 Magellan ® 9500 Expand UPC-E to EAN-13 Enables/disables expansion of UPC-E labels to EAN/JAN-13. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan either the enable or disable bar code below . Y ou ’ll need to cov er any unused bar codes on this and th e facing page to ensure that the scanner reads only the bar code you intend to[...]

UPC-E Enable Product Reference Guide 6-135 UPC-E Label ID This feature specifies a UPC-E label ID to be added to bar code data. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET UPC-E LABEL ID below . Y ou ’ll need to cover any unused bar codes on this and the facing page to ensur e the scanner reads only the bar code [...]

6-136 Magellan ® 9500 UPC-E 2-Digit Supplemental Label ID This feature specifies a UPC-E 2-Digit S upplemental label ID to be added to bar code data. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET UPC-E 2-DIGIT SUPPLEMENT AL LABEL ID below . Y ou ’ll need to cover any unused bar codes on this and the facing page to[...]

UPC-E Enable Product Reference Guide 6-137 UPC-E 5-Digit Supplemental Label ID This feature specifies a UPC-E 5-Digit S upplemental label ID to be added to bar code data. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET UPC-E 5-DIGIT SUPPLEMENT AL LABEL ID below . Y ou ’ll need to cover any unused bar codes on this an[...]

6-138 Magellan ® 9500 UPC-E 128 Supplemental Label ID This feature specifies a UPC-E 128 S upplemental label ID to be added to bar code data. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET UPC-E 128 SUPPLEMENT AL LABEL ID below . Y ou ’ll need to cover any unused bar codes on this and the fac- ing page to ensure th[...]

EAN-13 Enable Product Reference Guide 6-139 EAN-13 Enable Enables/disables the ability of the scanner to decode EAN/JAN-13 labels. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan either the enable or disable bar code below . Y ou ’ll need to cover any unused bar codes on this and th e facing page to ensure that the scanner reads only [...]

6-140 Magellan ® 9500 EAN-13 First Character Transmission Enables/disables transmission of EAN/JAN-13 first character . T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan either the enable or disable bar code below . Y ou ’ll need to cov er any unused bar codes on this and th e facing page to ensure that the scanner reads only the bar c[...]

EAN-13 Enable Product Reference Guide 6-141 EAN-13 Check Character Transmission Enables/disables transmission of an EAN/JAN-13 check character . T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan either the enable or disable bar code below . Y ou ’ll need to cover any unused bar codes on this and th e facing page to ensure that the scann[...]

6-142 Magellan ® 9500 EAN-13 ISBN Conversion Enable Enables/disables conversion of EAN/JAN-13 labels starting with 978 to Bookland ISBN labels. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan either the enable or disable bar code below . Y ou ’ll need to cov er any unused bar codes on this and th e facing page to ensure that the scan[...]

EAN-13 Enable Product Reference Guide 6-143 EAN 13 Label ID This feature specifies an EAN 13 label ID to be added to bar code data. T o set this feature: T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET EAN 13 LABEL ID below . Y ou ’ll need to cover any unused bar codes on this and the facing page to ensur e the scann[...]

6-144 Magellan ® 9500 EAN-13 2-Digit Supp lemental Label ID This feature specifies an EAN-13 2-Di git Supplemental label ID to be added to bar code data. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET EAN-13 2-DIGIT SUPPLEMENT AL LABEL ID below . Y ou ’ll need to cover any unused bar codes on this and the facing pa[...]

EAN-13 Enable Product Reference Guide 6-145 EAN-13 5-Digit Supplemental Label ID This feature specifies an EAN-13 5-Digit S upplemental label ID to be added to bar code data. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET EAN-13 5-DIGIT SUPPLEMENT AL LABEL ID below . Y ou ’ll need to cover any unused bar codes on th[...]

6-146 Magellan ® 9500 EAN-13 128 Supplemental Label ID This feature specifies an EAN-13 128 S upplemental label ID to be added to bar code data. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET EAN-13 128 SUPPLEMENT AL LABEL ID = DISABLE below . Y ou ’ll need to cover any unused bar codes on this and the facing page [...]

EAN-13 Enable Product Reference Guide 6-147 Bookland AIM ID This feature enables/disables transm ission of the Bookland AIM symbol- ogy identifier . T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan your selection from the bar codes below . Y ou ’ll need to cover any unused bar codes on this and th e facing page to ensure that the scann[...]

6-148 Magellan ® 9500 Bookland Label ID This feature specifies a Bookland label ID to be added to bar code data. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET BOOKLAND LABEL ID below . Y ou ’ll need to cover any unused bar codes on this and the facing page to ensur e the scanner reads only the bar code you intend [...]

EAN-8 Enable Product Reference Guide 6-149 EAN-8 Enable Enables/disables the ability of the scanner to decode EAN/JAN-8 labels. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan either the enable or disable bar code below . Y ou ’ll need to cover any unused bar codes on this and th e facing page to ensure that the scanner reads only the[...]

6-150 Magellan ® 9500 EAN-8 Check Character Transmission Enables/disables transmission of an EAN/JAN-8 check character . T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan either the enable or disable bar code below . Y ou ’ll need to cov er any unused bar codes on this and th e facing page to ensure that the scanner reads only the bar [...]

EAN-8 Enable Product Reference Guide 6-151 Expand EAN-8 to EAN-13 Enables/disables expansion of EAN/JAN-8 labels to EAN/JAN-13. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan either the enable or disable bar code below . Y ou ’ll need to cover any unused bar codes on this and th e facing page to ensure that the scanner reads only the[...]

6-152 Magellan ® 9500 EAN 8 Label ID This feature specifies an EAN 8 label ID to be added to bar code data. T o set this feature: T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET EAN 8 LABEL ID b e l o w . Y o u’ l l n e e d t o c o v e r any un use d ba r co de s on thi s a nd t he f ac ing pag e to en sure the sca [...]

EAN-8 Enable Product Reference Guide 6-153 EAN-8 2-Digit Supplemental Label ID This feature specifies an EAN-8 2-Digit S upplemental label ID to be added to bar code data. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET EAN-8 2-DIGIT SUPPLEMENT AL LABEL ID below . Y ou ’ll need to cover any unused bar codes on this a[...]

6-154 Magellan ® 9500 EAN-8 5-Digit Supplemental Label ID This feature specifies an EAN-8 5-Digit S upplemental label ID to be added to bar code data. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET EAN-8 5-DIGIT SUPPLEMENT AL LABEL ID below . Y ou ’ll need to cover any unused bar codes on this and the facing page t[...]

EAN-8 Enable Product Reference Guide 6-155 EAN-8 128 Supplemental Label ID This feature specifies an EAN-8 128 S upplemental label ID to be added to bar code data. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET EAN-8 128 SUPPLEMENT AL LABEL ID below . Y ou ’ll need to cov er any unused bar codes on this and the fac-[...]

6-156 Magellan ® 9500 EAN-8 Decoding Levels Decoding levels allo w the decoder to be set to perform at one of four selectable levels: • V ery Conser vative — S lower scan time, virtually eleminates mis- reads. The most secure setting. • Slightly M ore Aggressiv e — F aster scanning, more aggressiv e, yet minimizes misreads. • M oderately[...]

EAN-8 Enable Product Reference Guide 6-157 EAN-8 Decoding Levels — continued Remember to co ver any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code y ou intend to scan. EAN-8 DECODING LEVELS = VER Y CONSER V A TIVE EAN-8 DECODING LEVELS = SLIGHTL Y MORE A GGRESSIVE[...]

6-158 Magellan ® 9500 EAN-8 Decoding Levels — continued Remember to co ver any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code y ou intend to scan. EAN-8 DECODING LEVELS = MODERA TEL Y A GGRESSIVE EAN-8 DECODING LEVELS = VER Y AGGRESSIVE[...]

Other UPC/EAN Options Product Reference Guide 6-159 Other UPC/EAN Options The following pages contain other selectable features for UPC/EAN sym- bologies: • UPC/EAN Reconstruction • P rice W eight Check • Enable EAN T wo Label •A d d o n s • UPC-A and EAN-13 Decoding Levels[...]

6-160 Magellan ® 9500 UPC/EAN Reconstruction Enables/disables the ability of the scanner to decode a class of UPC/EAN labels with voids. The label voids ma y be caused by printing defects or physical damage. This feature may be helpful in environments with in- store printed labels. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan either[...]

Other UPC/EAN Options Product Reference Guide 6-161 Price Weight Check Enables/disables calculation and verification of price/weight check digits. Applies to all UPC-A and EAN/JAN-13 labels with eligible 1 Num b e r S y s - tem/F irst Character digits. Options are: •D i s a b l e • 4-digit price/weight • 5-digit price/weight • 4-digit Eur o[...]

6-162 Magellan ® 9500 Price Weight Check — continued Remember to co ver any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code y ou intend to scan. PRICE WEIGHT CHECK = 4-DIGIT PRICE/WEIGHT PRICE WEIGHT CHECK = 5-DIGIT PRICE/WEIGHT[...]

Other UPC/EAN Options Product Reference Guide 6-163 Price Weight Check — continued Remember to co ver any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code y ou intend to scan. PRICE WEIGHT CHECK = 4-DIGIT EUROPEAN PRICE/WEIGHT PRICE WEIGHT CHECK = 5-DIGIT EUROPEAN PRICE/WEIGHT[...]

6-164 Magellan ® 9500 Enable EAN Two Label Enables/disables the ability of the scanner to decode EAN two-label pairs. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan either the enable or disable bar code below . Y ou ’ll need to cov er any unused bar codes on this and th e facing page to ensure that the scanner reads only the bar cod[...]

Other UPC/EAN Options Product Reference Guide 6-165 Addons The scanner is capable of processing different types of addon codes, including: • 2-Digit S upplemental • 5-Digit S upplemental Options are pro vided on the following pages for your convenience: • Disable all addons — The scanner will not look for or read addons. • Optional 2-Digi[...]

6-166 Magellan ® 9500 Addons — continued Remember to co ver any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code y ou intend to scan. ADDONS = OPTIONAL 2-DIGIT AND 5-DIGIT SUPPLEMENT AL[...]

Other UPC/EAN Options Product Reference Guide 6-167 UPC-A and EAN-13 Decoding Levels Decoding levels allo w the decoder to be set to perform at one of four selectable levels: • V ery Conser vative — S lower scan time, virtually eleminates mis- reads. The most secure setting. • Slightly M ore Aggressiv e — F aster scanning, more aggressiv e,[...]

6-168 Magellan ® 9500 UPC-A and EAN-13 Decoding Levels — continued Remember to co ver any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code y ou intend to scan. UPC-A/EAN-13 DECODING LEVELS = VER Y CONSER V A TIVE UPC-A/EAN-13 DECODING LEVELS = SLIGHTL Y MORE A GGRESSIVE[...]

Other UPC/EAN Options Product Reference Guide 6-169 UPC-A and EAN-13 Decoding Levels — continued Remember to co ver any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code y ou intend to scan. UPC-A/EAN-13 DECODING LEVELS = MODERA TEL Y A GGRESSIVE UPC-A/EAN-13 DECODING LEVELS = VER Y AGGRESSIVE[...]

6-170 Magellan ® 9500 GTIN Enable Enables/Disables the ability to convert UPCE, UPCA, EAN8, and EAN13 labels into the GTIN 14-character format. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan either the enable or disable bar code below . Y ou ’ll need to cov er any unused bar codes on this and th e facing page to ensure that the scan[...]

GTIN Enable Product Reference Guide 6-171 GTIN Label ID This feature specifies a GTIN label ID to be added to bar code data when GTIN conversion is enabled. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET GTIN LABEL ID be low . Y ou’ l l n eed to cove r any unused bar codes on this and the facing page to ensure the s[...]

6-172 Magellan ® 9500 GTIN 2-Digit Supplemental Label ID This feature specifies a GTIN label ID to be added to bar code data when GTIN conversion is enabled and 2-digit supplemental addon bar code labels are converted. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET GTIN 2-DIGIT SUPPLEMENT AL LABEL ID below . Y ou ’[...]

GTIN Enable Product Reference Guide 6-173 GTIN 5-Digit Supplemental Label ID This feature specifies a GTIN label ID to be added to bar code data when GTIN conversion is enabled and 5- digit supplemental addon bar code labels are converted. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET GTIN 5-DIGIT SUPPLEMENT AL LABEL[...]

6-174 Magellan ® 9500 GTIN Code 128 Supplemental Label ID This feature specifies a GTIN label ID to be added to bar code data when GTIN conversion is enabled and Code 128 supplemental addon bar code labels are converted T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET GTIN CODE 128 SUPPLEMENT AL LABEL ID below . Y ou ?[...]

RSS-14 Enable Product Reference Guide 6-175 RSS-14 Enable Enables/disables the ability of the scanner to decode RSS-14 labels. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan either the enable or disable bar code below . Y ou ’ll need to cover any unused bar codes on this and th e facing page to ensure that the scanner reads only the [...]

6-176 Magellan ® 9500 RSS-14 Check Character Transmission Enables/disables transmission of the RSS-14 check character . T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan either the enable or disable bar code below . Y ou ’ll need to cov er any unused bar codes on this and th e facing page to ensure that the scanner reads only the bar c[...]

RSS-14 Enable Product Reference Guide 6-177 RSS-14/EAN-128 Emulation Enables/disables the ability of RS S-14 to be transmitted as EAN-128. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan either the enable or disable bar code below . Y ou ’ll need to cover any unused bar codes on this and th e facing page to ensure that the scanner rea[...]

6-178 Magellan ® 9500 RSS-14 2D Component Enable When this feature is enabled, and the software r eads an RSS-14 bar code that has a 2D component associated with it, the RSS-14 bar code will not be reported to the terminal. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan your selection from the bar codes below . Y ou ’ll need to cove[...]

RSS-14 Enable Product Reference Guide 6-179 RSS-14 AIM ID This feature enables/disables transmission of the RSS-14 AIM symbology identifier . T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan your selection from the bar codes below . Y ou ’ll need to cover any unused bar codes on this and th e facing page to ensure that the scanner read[...]

6-180 Magellan ® 9500 RSS-14 Label ID This feature specifies an RSS-14 label ID to be added to bar code data. T o set this feature: T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET RSS-14 LABEL ID below . Y ou ’ll need to cover any unused bar codes on this and the facing page to ensur e the scanner reads only the bar[...]

RSS Expanded Enable Product Reference Guide 6-181 RSS Expanded Enable Enables/disables the ability of the scanner to decode RSS-Expanded labels. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan either the enable or disable bar code below . Y ou ’ll need to cover any unused bar codes on this and th e facing page to ensure that the scann[...]

6-182 Magellan ® 9500 RSS Expanded EAN-128 Emulation Enables/disables EAN-128 emulation for RSS Expanded. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan either the enable or disable bar code below . Y ou ’ll need to cov er any unused bar codes on this and th e facing page to ensure that the scanner reads only the bar code you intend[...]

RSS Expanded Enable Product Reference Guide 6-183 RSS Expanded 2D Component Enable When this feature is enabled, and the software r eads an RSS Expanded bar code that has a 2D component associated with it, the RSS Expanded bar code will not be reported to the terminal. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan your selection from [...]

6-184 Magellan ® 9500 RSS Expanded AIM ID This feature enables/disables tran smission of the RSS Expanded AIM symbology identifier . T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan your selection from the bar codes below . Y ou ’ll need to cover any unused bar codes on this and th e facing page to ensure that the scanner reads only t[...]

RSS Expanded Enable Product Reference Guide 6-185 RSS Expanded Label ID This feature specifies an RSS Expanded label ID to be added to bar code data. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET RSS EXP ANDED LABEL ID below . Y ou ’ll need to cover any unused bar codes on this and the facing page to ensure the sca[...]

6-186 Magellan ® 9500 RSS Expanded Length Control This feature specifies either variable -length or fix ed-length decoding for RSS Expanded. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan your selection from the bar codes below . Y ou ’ll need to cover any unused bar codes on this and th e facing page to ensure that the scanner read[...]

RSS Expanded Enable Product Reference Guide 6-187 RSS Expanded Maximum Label Length This feature specifies the maximum al lowable length of an RSS E xpanded label. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET RSS EXP ANDED MAXIMUM LABEL LENGTH below . Y ou ’ll need to cover any unused bar codes on this and the fac[...]

6-188 Magellan ® 9500 RSS Expanded Minimum Label Length This feature specifies the minimum allo wable length of an RSS Expanded label. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET RSS EXP ANDED MINIMUM LABEL LENGTH below . Y ou ’ll need to cover any unused bar codes on this and the facing page to ensure that the [...]

RSS Expanded Enable Product Reference Guide 6-189 RSS Expanded Fixed Length 1 This feature specifies RSS Expanded first fix ed length. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET RSS EXP ANDED FIXED LENGTH 1 below . Y ou ’ll need to cov er any unused bar codes on this and the facing page to ensure that the scanne[...]

6-190 Magellan ® 9500 RSS Expanded Fixed Length 2 This feature specifies RSS Expanded second fix ed length. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET RSS EXP ANDED FIXED LENGTH 2 below . Y ou ’ll need to cov er any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code [...]

Code 39 Enable Product Reference Guide 6-191 Code 39 Enable Enables/disables the ability of the scanner to decode Code 39 labels. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan either the enable or disable bar code below . Y ou ’ll need to cover any unused bar codes on this and th e facing page to ensure that the scanner reads only t[...]

6-192 Magellan ® 9500 Code 39 Start Stop Character Transmission Enables/disables transmission of Code 39 start and stop characters. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan either the enable or disable bar code below . Y ou ’ll need to cov er any unused bar codes on this and th e facing page to ensure that the scanner reads on[...]

Code 39 Enable Product Reference Guide 6-193 Code 39 Check Character Calculation Enables/disables calculation and verifi cation of an optional Code 39 check character . When disabled, any check char acter in label is treated as a data character . T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan either the enable or disable bar code below[...]

6-194 Magellan ® 9500 Code 39 Check Character Transmission Enables/disables transmission of optional Code 39 check character . T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan either the enable or disable bar code below . Y ou ’ll need to cov er any unused bar codes on this and th e facing page to ensure that the scanner reads only th[...]

Code 39 Enable Product Reference Guide 6-195 Code 39 Full ASCII Enables/disables the ability of the sc anner to translate to Code 39 full ASCII labels. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan either the enable or disable bar code below . Y ou ’ll need to cover any unused bar codes on this and th e facing page to ensure that th[...]

6-196 Magellan ® 9500 Code 39 AIM ID This feature enables/disables transmission of the Code 39 AIM symbology identifier . T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan your selection from the bar codes below . Y ou ’ll need to cover any unused bar codes on this and th e facing page to ensure that the scanner reads only the bar code[...]

Code 39 Enable Product Reference Guide 6-197 Code 39 Label ID This feature specifies a Code 39 label ID to be added to bar code data. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET CODE 39 LABEL ID below . Y ou ’ll need to cover any unused bar codes on this and the facing page to ensur e the scanner reads only the b[...]

6-198 Magellan ® 9500 Code 39 Length Control This feature specifies whether variable-length or fix ed-length decoding will be set for Code 39. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan your selection from the bar codes below . Y ou ’ll need to cover any unused bar codes on this and th e facing page to ensure that the scanner re[...]

Code 39 Enable Product Reference Guide 6-199 Code 39 Maximum Label Length This feature specifies the maximum al lowable length of a Code 39 label. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET CODE 39 MAXIMUM LABEL LENGTH below . Y ou ’ll need to cov er any unused bar codes on this and the fac- ing page to ensure t[...]

6-200 Magellan ® 9500 Code 39 Minimum Label Length This feature specifies the minimum al lowable length of a Code 39 label. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET CODE 39 MINIMUM LABEL LENGTH below . Y ou ’ll need to cover any unused bar codes on this and the fac- ing page to ensure that the scanner reads o[...]

Code 39 Enable Product Reference Guide 6-201 Code 39 Fixed Length 1 This feature specifies Code 39 first fixed length. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET CODE 39 FIXED LENGTH 1 below . Y ou ’ll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar co[...]

6-202 Magellan ® 9500 Code 39 Fixed Length 2 This feature specifies Code 39 second fix ed length. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET CODE 39 FIXED LENGTH 2 below . Y ou ’ll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code y ou intend to sc[...]

Code 39 Enable Product Reference Guide 6-203 Code 39 Stitching Enables/disables stitching for Code 39 labels. When parts of a Code 39 bar code are presented to the scanner with this featur e enabled, the bar code parts will be assembled by the scanner’ s software, and the data will be decoded if all bar code proofing requir ements are met. T o se[...]

6-204 Magellan ® 9500 Pharmacode 39 Enable Enables/disables the ability of the scanner to decode I talian Pharmacode 39 labels. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan either the enable or disable bar code below . Y ou ’ll need to cov er any unused bar codes on this and th e facing page to ensure that the scanner reads only t[...]

Pharmacode 39 Enable Product Reference Guide 6-205 Pharmacode 39 Start Stop Character Transmission Enables/ disables transmission of start and stop characters for Pharmacode 39. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan either the enable or disable bar code below . Y ou ’ll need to cover any unused bar codes on this and th e fac[...]

6-206 Magellan ® 9500 Pharmacode 39 Check Character Transmission Enables/disables transmission of Pharmacode 39 check character . T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan either the enable or disable bar code below . Y ou ’ll need to cov er any unused bar codes on this and th e facing page to ensure that the scanner reads only[...]

Pharmacode 39 Enable Product Reference Guide 6-207 Pharmacode 39 Label ID This feature specifies a Pharmacode 39 label ID to be added to bar code data. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET PHARMACODE 39 LABEL ID below . Y ou ’ll need to cover any unused bar codes on this and the facing page to ensure the s[...]

6-208 Magellan ® 9500 Code 128 Enable Enables/disables 1 the ability of the scanner to decode Code 128 labels. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan either the enable or disable bar code below . Y ou ’ll need to cov er any unused bar codes on this and th e facing page to ensure that the scanner reads only the bar code you i[...]

Code 128 Enable Product Reference Guide 6-209 Code 128 Transmit Function Characters Enables/disables transmission of Code 128 function characters 1, 2, 3, and 4. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan either the enable or disable bar code below . Y ou ’ll need to cover any unused bar codes on this and th e facing page to ensu[...]

6-210 Magellan ® 9500 Convert Code 128 to Code 39 Enables/disables conversion of Code 128 labels to Code 39. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan either the enable or disable bar code below . Y ou ’ll need to cov er any unused bar codes on this and th e facing page to ensure that the scanner reads only the bar code you int[...]

Code 128 Enable Product Reference Guide 6-211 Code 128 AIM ID This feature enables/disables transmission of the Code 128 AIM symbol- ogy identifier . T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan your selection from the bar codes below . Y ou ’ll need to cover any unused bar codes on this and th e facing page to ensure that the scan[...]

6-212 Magellan ® 9500 Code 128 Label ID This feature specifies a Code 128 label ID to be added to bar code data.. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET CODE 128 LABEL ID below . Y ou ’ll need to cover any unused bar codes on this and the facing page to ensur e the scanner reads only the bar code you intend[...]

Code 128 Enable Product Reference Guide 6-213 Code 128 Length Control This feature specifies whether variable-length or fix ed-length decoding will be set for Code 128. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan your selection from the bar codes below . Y ou ’ll need to cover any unused bar codes on this and th e facing page to e[...]

6-214 Magellan ® 9500 Code 128 Maximum Label Length This feature specifies the maximum al lowable length of a Code 128 label. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET CODE 128 MAXIMUM LABEL LENGTH below . Y ou ’ll need to cover any unused bar codes on this and the fac- ing page to ensure that the scanner read[...]

Code 128 Enable Product Reference Guide 6-215 Code 128 Minimum Label Length This feature specifies the minimum al lowable length of a Code 128 label. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET CODE 128 MINIMUM LABEL LENGTH below . Y ou ’ll need to cov er any unused bar codes on this and the fac- ing page to ensu[...]

6-216 Magellan ® 9500 Code 128 Fixed Length 1 This feature specifies Code 128 first fixed length. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET CODE 128 FIXED LENGTH 1 below . Y ou ’ll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code y ou intend to s[...]

Code 128 Enable Product Reference Guide 6-217 Code 128 Fixed Length 2 This feature specifies Code 128 second fixed length. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET CODE 128 FIXED LENGTH 2 below . Y ou ’ll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the b[...]

6-218 Magellan ® 9500 Code 128 Stitching Enables/disables stitching for Code 128 labels. When parts of a Code 128 bar code are presented to the scanner with this featur e enabled, the bar code parts will be assembled by the scanner’ s software, and the data will be decoded if all bar code proofing requir ements are met. T o set this feature: 1. [...]

EAN-128 Enable Product Reference Guide 6-219 EAN-128 Enable Enables/disables the ability of the scanner to decode EAN-128 labels. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan either the enable or disable bar code below . Y ou ’ll need to cover any unused bar codes on this and th e facing page to ensure that the scanner reads only t[...]

6-220 Magellan ® 9500 EAN-128 AIM ID This feature enables/disables tran smission of the EAN-128 AIM symbol- ogy identifier . T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan your selection from the bar codes below . Y ou ’ll need to cover any unused bar codes on this and th e facing page to ensure that the scanner reads only the bar c[...]

EAN-128 Enable Product Reference Guide 6-221 EAN-128 Label ID This feature specifies an EAN-128 label ID to be added to bar code data.. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET EAN-128 LABEL ID below . Y ou ’ll need to cover any unused bar codes on this and the facing page to ensur e the scanner reads only the[...]

6-222 Magellan ® 9500 Interleaved 2 of 5 (I 2 of 5) Enable Enables/disables the ability of the scanner to decode Interleaved 2 of 5 labels. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan either the enable or disable bar code below . Y ou ’ll need to cov er any unused bar codes on this and th e facing page to ensure that the scanner [...]

Interleaved 2 of 5 (I 2 of 5) Enable Product Reference Guide 6-223 I 2 of 5 Check Character Calculation Enables/disables calculation and verification of an optional Interleav ed 2 of 5 check character . T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan either the enable or disable bar code below . Y ou ’ll need to cover any unused bar c[...]

6-224 Magellan ® 9500 I 2 of 5 Check Character Transmission Enables/disables transmission of an optional Interleaved 2 of 5 check char- acter . T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan either the enable or disable bar code below . Y ou ’ll need to cov er any unused bar codes on this and th e facing page to ensure that the scan[...]

Interleaved 2 of 5 (I 2 of 5) Enable Product Reference Guide 6-225 I 2 of 5 AIM ID This feature enables/disables transmi ssion of the I 2 of 5 AIM symbology identifier . T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan your selection from the bar codes below . Y ou ’ll need to cover any unused bar codes on this and th e facing page to [...]

6-226 Magellan ® 9500 I 2 of 5 Label ID This feature specifies an I 2 of 5 labe l ID to be added to bar code data.. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET I 2 of 5 LABEL ID b e l o w . Y o u’l l n e e d t o c o v e r any un use d ba r co de s on thi s a nd t he f ac ing pag e to en sure the sca n- ner reads[...]

Interleaved 2 of 5 (I 2 of 5) Enable Product Reference Guide 6-227 I 2 of 5 Length Control This feature specifies whether variable-length or fix ed-length decoding will be set for I 2 of 5. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan your selection from the bar codes below . Y ou ’ll need to cover any unused bar codes on this and [...]

6-228 Magellan ® 9500 I 2 of 5 Maximum Label Length This feature specifies the maximum allo wable length of an I 2 of 5 label. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET I 2 OF 5 MAXIMUM LABEL LENGTH below . Y ou ’ll need to cover any unused bar codes on this and the fac- ing page to ensure that the scanner rea[...]

Interleaved 2 of 5 (I 2 of 5) Enable Product Reference Guide 6-229 I 2 of 5 Minimum Label Length This feature specifies the minimum allo wable length of an I 2 of 5 label. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET I 2 OF 5 MINIMUM LABEL LENGTH below . Y ou ’ll need to cov er any unused bar codes on this and the[...]

6-230 Magellan ® 9500 I 2 of 5 Fixed Length 1 This feature specifies I 2 of 5 first fix ed length. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET I 2 OF 5 FIXED LENGTH 1 below . Y ou ’ll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code y ou intend to [...]

Interleaved 2 of 5 (I 2 of 5) Enable Product Reference Guide 6-231 I 2 of 5 Fixed Length 2 This feature specifies I 2 of 5 second fixed length. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET I 2 OF 5 FIXED LENGTH 2 below . Y ou ’ll need to cover any unused bar codes on this and the facing page to ensure that the sca[...]

6-232 Magellan ® 9500 I 2 of 5 Stitching Enables/disables stitching for I 2 of 5 labels. When parts of an I 2 of 5 bar code are presented to the scanner with this featur e enabled, the bar code parts will be assembled by the scanner’ s software, and the data will be decoded if all bar code proofing requir ements are met. T o set this feature: 1.[...]

Codabar Enable Product Reference Guide 6-233 Codabar Enable Enables/disables the ability of the scanner to decode Codabar labels. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan either the enable or disable bar code below . Y ou ’ll need to cover any unused bar codes on this and th e facing page to ensure that the scanner reads only t[...]

6-234 Magellan ® 9500 Codabar Start Stop Character Transmission Enables/disables transmission of Codabar start and stop characters. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan either the enable or disable bar code below . Y ou ’ll need to cov er any unused bar codes on this and th e facing page to ensure that the scanner reads on[...]

Codabar Enable Product Reference Guide 6-235 Codabar Start Stop Character Set This feature selects the format of tr ansmitted Codabar start/stop charac- ters. Options are: •A B C D / T N * E •A B C D / A B C D • abcd/tn* e •a b c d / a b c d T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code below or from the follo win[...]

6-236 Magellan ® 9500 Codabar Start Stop Character Set — continued Remember to co ver any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code y ou intend to scan. COD ABAR ST ART ST OP CHARACTER = abcd/tn* e COD ABAR ST ART ST OP CHARACTER = abcd/abcd[...]

Codabar Enable Product Reference Guide 6-237 Codabar Start Stop Character Match Enables/disables the requir ement that start and stop characters match. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan either the enable or disable bar code below . Y ou ’ll need to cover any unused bar codes on this and th e facing page to ensure that th[...]

6-238 Magellan ® 9500 Codabar Check Character Calculation Enables/disables calculation and verification of an optional Codabar check character. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan either the enable or disable bar code below . Y ou ’ll need to cov er any unused bar codes on this and th e facing page to ensure that the scan[...]

Codabar Enable Product Reference Guide 6-239 Codabar Check Character Transmission Enables/disables transmission of an optional Codabar check character . T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan either the enable or disable bar code below . Y ou ’ll need to cover any unused bar codes on this and th e facing page to ensure that t[...]

6-240 Magellan ® 9500 Codabar AIM ID This feature enables/disables transm ission of the Codabar AIM symbology identifier . T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan your selection from the bar codes below . Y ou ’ll need to cover any unused bar codes on this and th e facing page to ensure that the scanner reads only the bar cod[...]

Codabar Enable Product Reference Guide 6-241 Codabar Label ID This feature specifies a Codabar label ID to e added to bar code data. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET CODABAR LABEL ID below . Y ou ’ll need to cover any unused bar codes on this and the facing page to ensur e the scanner reads only the ba[...]

6-242 Magellan ® 9500 Codabar Length Control This feature specifies whether variable-length or fix ed-length decoding will be set for Codabar . T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan your selection from the bar codes below . Y ou ’ll need to cover any unused bar codes on this and th e facing page to ensure that the scanner r[...]

Codabar Enable Product Reference Guide 6-243 Codabar Maximum Label Length This feature specifies the maximum al lowable length of a Codabar label. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET CODABAR MAXIMUM LABEL LENGTH below . Y ou ’ll need to cov er any unused bar codes on this and the fac- ing page to ensure t[...]

6-244 Magellan ® 9500 Codabar Minimum Label Length This feature specifies the minimum al lowable length of a Codabar label. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET CODABAR MINIMUM LABEL LENGTH below . Y ou ’ll need to cover any unused bar codes on this and the fac- ing page to ensure that the scanner reads o[...]

Codabar Enable Product Reference Guide 6-245 Codabar Fixed Length 1 This feature specifies Codabar first fix ed length. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET CODABAR FIXED LENGTH 1 below . Y ou ’ll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar c[...]

6-246 Magellan ® 9500 Codabar Fixed Length 2 This feature specifies Codabar second fixed length. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET CODABAR FIXED LENGTH 2 below . Y ou ’ll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code y ou intend to sca[...]

Codabar Enable Product Reference Guide 6-247 Codabar Stitching Enables/disables stitching for Codabar labels. When parts of a Codabar bar code are presented to the scanner with this featur e enabled, the bar code parts will be assembled by the scanner’ s software, and the data will be decoded if all bar code proofing requir ements are met. T o se[...]

6-248 Magellan ® 9500 Code 93 Enable Enables/disables the ability of the scanner to decode Code 93 labels. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan either the enable or disable bar code below . Y ou ’ll need to cov er any unused bar codes on this and th e facing page to ensure that the scanner reads only the bar code you inten[...]

Code 93 Enable Product Reference Guide 6-249 Code 93 AIM ID This feature enables/disables transm ission of the Code 93 AIM symbology identifier . T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan your selection from the bar codes below . Y ou ’ll need to cover any unused bar codes on this and th e facing page to ensure that the scanner [...]

6-250 Magellan ® 9500 Code 93 Label ID This feature specifies a Code 93 label ID to be added to bar code data.. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET CODE 93 LABEL ID below . Y ou ’ll need to cover any unused bar codes on this and the facing page to ensur e the scanner reads only the bar code you intend to[...]

Code 93 Enable Product Reference Guide 6-251 Code 93 Length Control This feature specifies whether variable-length or fix ed-length decoding will be set for Code 93. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan your selection from the bar codes below . Y ou ’ll need to cover any unused bar codes on this and th e facing page to ensu[...]

6-252 Magellan ® 9500 Code 93 Maximum Label Length This feature specifies the maximum al lowable length of a Code 93 label. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET CODE 93 MAXIMUM LABEL LENGTH below . Y ou ’ll need to cover any unused bar codes on this and the fac- ing page to ensure that the scanner reads o[...]

Code 93 Enable Product Reference Guide 6-253 Code 93 Minimum Label Length This feature specifies the minimum al lowable length of a Code 93 label. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET CODE 93 MINIMUM LABEL LENGTH below . Y ou ’ll need to cov er any unused bar codes on this and the fac- ing page to ensure t[...]

6-254 Magellan ® 9500 Code 93 Fixed Length 1 This feature specifies Code 93 first fixed length. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET CODE 93 FIXED LENGTH 1 below . Y ou ’ll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code y ou intend to scan[...]

Code 93 Enable Product Reference Guide 6-255 Code 93 Fixed Length 2 This feature specifies Code 93 second fix ed length. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET CODE 93 FIXED LENGTH 2 below . Y ou ’ll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar [...]

6-256 Magellan ® 9500 Code 93 Stitching Enables/disables stitching for Code 93 labels. When parts of a Code 93 bar code are presented to the scanner with this featur e enabled, the bar code parts will be assembled by the scanner’ s software, and the data will be decoded if all bar code proofing requir ements are met. T o set this feature: 1. Sca[...]

MSI/Plessey Enable Product Reference Guide 6-257 MSI/Plessey Enable Enables/disables the ability of the scanner to decode MSI/Plessey labels. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan either the enable or disable bar code below . Y ou ’ll need to cover any unused bar codes on this and th e facing page to ensure that the scanner [...]

6-258 Magellan ® 9500 MSI/Plessey Check Character Calculation Enables/disables calculation and verification of optional MSI/Plessey check characters. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan either the enable or disable bar code below . Y ou ’ll need to cov er any unused bar codes on this and th e facing page to ensure that th[...]

MSI/Plessey Enable Product Reference Guide 6-259 MSI/Plessey Number of Check Characters S pecifies number of MSI/Plessey check characters to be calculated and verif ied. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code below repr esenting the desired number of MSI/ Plessey check characters to be calcul ated and verified. Y o[...]

6-260 Magellan ® 9500 MSI/Plessey Check Character Transmission Enables/disables transmission of optional MSI/Plessey check characters. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan either the enable or disable bar code below . Y ou ’ll need to cov er any unused bar codes on this and th e facing page to ensure that the scanner reads[...]

MSI/Plessey Enable Product Reference Guide 6-261 MSI/Plessey AIM ID This feature enables/disables transmission of the MSI/Plessey AIM sym- bology identifier . T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan your selection from the bar codes below . Y ou ’ll need to cover any unused bar codes on this and th e facing page to ensure that[...]

6-262 Magellan ® 9500 MSI/Plessey Label ID This feature specifies an MSI/Plessey label ID to be added to bar code data. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET MSI/PLESSEY LABEL ID b e l o w . Y o u’l l n e e d to cover any unused bar codes on this and the facing page to ensur e the scanner reads only the ba[...]

MSI/Plessey Enable Product Reference Guide 6-263 MSI/Plessey Length Control This feature specifies whether variable-length or fix ed-length decoding will be set for MSI/Plessey . T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan your selection from the bar codes below . Y ou ’ll need to cover any unused bar codes on this and th e facing[...]

6-264 Magellan ® 9500 MSI/Plessey Maximum Label Length This feature specifies the maximum al lowable length of an MSI/Plessey label. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET MSI/PLESSEY MAXIMUM LABEL LENGTH below . Y ou ’ll need to cover any unused bar codes on this and the facing page to ensure that the scan[...]

MSI/Plessey Enable Product Reference Guide 6-265 MSI/Plessey Minimum Label Length This feature specifies the minimum al lowable length of an MSI/Plessey label. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET MSI/PLESSEY MINIMUM LABEL LENGTH below . Y ou ’ll need to cover any unused bar codes on this and the facing pa[...]

6-266 Magellan ® 9500 MSI/Plessey Fixed Length 1 This feature specifies MSI/Plessey first fixed length. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET MSI/PLESSEY FIXED LENGTH 1 below . Y ou ’ll need to cov er any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code y ou i[...]

MSI/Plessey Enable Product Reference Guide 6-267 MSI/Plessey Fixed Length 2 This feature specifies MSI/Plessey second fix ed length. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET MSI/PLESSEY FIXED LENGTH 2 below . Y ou ’ll need to cov er any unused bar codes on this and the facing page to ensure that the scanner re[...]

6-268 Magellan ® 9500 MSI/Plessey Stitching Enables/disables stitching for MSI/Plessey labels. When parts of an MSI/ Plessey bar code are pr esented to the sc anner with this feature enabled, the bar code parts will be assembled by the scanner’ s software, and the data will be decoded if all bar code proofing requir ements are met. T o set this [...]

Standard 2 of 5 Enable Product Reference Guide 6-269 Standard 2 of 5 Enable Enables/disables the ability of the scanner to decode S tandard 2 of 5 labels. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan either the enable or disable bar code below . Y ou ’ll need to cover any unused bar codes on this and th e facing page to ensure that[...]

6-270 Magellan ® 9500 Standard 2 of 5 Check Character Calculation Enables/disables calculation and verification of an optional S tandard 2 of 5 check character . T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan either the enable or disable bar code below . Y ou ’ll need to cov er any unused bar codes on this and th e facing page to en[...]

Standard 2 of 5 Enable Product Reference Guide 6-271 Standard 2 of 5 Check Character Transmission Enables/disables transmission of an optional S tandard 2 of 5 check charac- ter . T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan either the enable or disable bar code below . Y ou ’ll need to cover any unused bar codes on this and th e f[...]

6-272 Magellan ® 9500 Standard 2 of 5 AIM ID This feature enables/disables transm ission of the S tandard 2 of 5 AIM symbology identifier . T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan your selection from the bar codes below . Y ou ’ll need to cover any unused bar codes on this and th e facing page to ensure that the scanner reads[...]

Standard 2 of 5 Enable Product Reference Guide 6-273 Standard 2 of 5 Label ID This feature specifies an S tandard 2 of 5 label ID to be added to bar code data. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET ST ANDARD 2 of 5 LABEL ID below . Y ou ’ll need to cover any unused bar codes on this and the facing page to e[...]

6-274 Magellan ® 9500 Standard 2 of 5 Length Control This feature specifies whether variable-length or fix ed-length decoding will be set for Standard 2 of 5. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan your selection from the bar codes below . Y ou ’ll need to cover any unused bar codes on this and th e facing page to ensure tha[...]

Standard 2 of 5 Enable Product Reference Guide 6-275 Standard 2 of 5 Maximum Label Length This feature specifies the maximum allo wable length of a S tandard 2 of 5 label. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET ST ANDARD 2 OF 5 MAXIMUM LABEL LENGTH below . Y ou ’ll need to cover any unused bar codes on this [...]

6-276 Magellan ® 9500 Standard 2 of 5 Minimum Label Length This feature specifies the minimum allo wable length of an Standard 2 of 5 label. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET ST ANDARD 2 OF 5 MINIMUM LABEL LENGTH below . Y ou ’ll need to cover any unused bar codes on this and the facing page to ensure [...]

Standard 2 of 5 Enable Product Reference Guide 6-277 Standard 2 of 5 Fixed Length 1 This feature specifies S tandard 2 of 5 first fixed length. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET ST ANDARD 2 OF 5 FIXED LENGTH 1 below . Y ou ’ll need to cov er any unused bar codes on this and the fac- ing page to ensure t[...]

6-278 Magellan ® 9500 Standard 2 of 5 Fixed Length 2 This feature specifies S tandard 2 of 5 second fixed length. T o set this feature: 1. Scan the SWIT CH bar code. 2. Scan the bar code, SET ST ANDARD 2 OF 5 FIXED LENGTH 2 below . Y ou ’ll need to cover any unused bar codes on this and the fac- ing page to ensure that the scanner reads only the[...]

Standard 2 of 5 Enable Product Reference Guide 6-279 Standard 2 of 5 Stitching Enables/disables stitching for S tandard 2 of 5 labels. When parts of a Stan- dard 2 of 5 bar code ar e presented to the scanner with this feature enabled, the bar code parts will be assembled by the scanner’ s software, and the data will be decoded if all bar code pro[...]

6-280 Magellan ® 9500 NOTES[...]

Product Reference Guide A-1 Appendix A LED/Beeper Indications & Controls Figure A-1 shows the operator ’ s controls and indicators. The descriptions following identify the use or function of each component. Figure A-1. Scanner and Scale Controls Manual EAS Deactivation Push Button V olume/T one Push Button Scale Zero Push Button EAS LED (T ri[...]

A-2 Magellan ® 9500 Controls and Indicators The control panel consists of three indicator LEDs and three push buttons as described in the following pages. The unit also includes a beeper which can be configured to sound indications of scanning, weighing, and deacti- vation activities. LED and Beeper Indications Scanner and Scale LEDs The Scanner L[...]

Controls and Indicators Product Reference Guide A-3 Host Disabled Scanner (Green) LED 1-second off, 1/ 10-second on Host has disabled scanning. Field Replace- able Unit (FR U ) W ar ning (Error Mode) Audib le low tone 1 second. Alternating Scanner/Scale (Green/ Y ellow) LEDs flash contin uously b . Ser ves notice that a f atal FRU f ailure has been[...]

A-4 Magellan ® 9500 Deactivator LED The Deactivator LED (tri-color , bottom-most) designates EAS deactiva- tion status (see Ta b l e A - 2 ). The table also pro vides information about spe- cial beeper indications which can be sounded in response to changes in deactivation status. Table A-2. EAS Indications EAS DEA CTIV A TION DISABLED INDICA TION[...]

Controls and Indicators Product Reference Guide A-5 COUPLED MODE ONL Y Deactivation Indicated Deactivation (T ri-color) LED flashes Red, then Orange, then returns to Green. Good read beep fol- lows deactiv ation. The EAS antenna has been triggered ON to deactivate a label follo wing suc- cessful bar code read. Manual Deacti- vation in Progress Deac[...]

A-6 Magellan ® 9500 Volume/Tone Push Button The V olume/T one P ush Button also pe rforms multiple functions depend- ing upon the duration of time it is pressed: HYBRID MODE Deactivation Indicated Deactivation (T ri-color) LED flashes Red, then Orange, then returns to Green. High frequency beep An EAS tag has been successfully deactivated. a. Addi[...]

Controls and Indicators Product Reference Guide A-7 Hold, then release when the beeper sounds Increments tone Press the push button f or approximately 2 seconds , then release. Each time this is done, the beeper will sound at one of three tones. Stop when the desired tone (high, medium or low) is sounded. 4 Seconds Scanner Diagnostics Mode a This m[...]

A-8 Magellan ® 9500 Manual EAS Deactivation Push Button U sing the programming bar codes contained in the P roduct Refer- ence Guide (PR G) the button can be configured to operate always, or only function when the scanner is enabled. PRESS DURA TION FUNCTION COMMENT Momentar y a Man ually initiates EAS deactivation Place the item with the EAS tag [...]

Controls and Indicators Product Reference Guide A-9 Scale Zero Push Button The Scale Zero P ush Button is used for multiple functions as listed in Ta b l e A - 4 . NO TE The Scale Zero Push Button has no function in a “scanner onl y” model. Table A-4. Scale Zero Push Button Functions PRESS DURA TION FUNCTION COMMENT Momentary Zero Scale When pr[...]

A-10 Magellan ® 9500 Calibration Switch This switch initiates the scale ’ s calibration routine. A cer tified weight set is needed to perform the scale calibration steps detailed in Chapter 5 , Cali- bration . This switch is not included in scanners without scale modules. Calibration Switch Seal This seal allows you to secur e the Calibration Sw[...]

Product Reference Guide B-1 Appendix B Cable Information Introduction The following pages contain pinout information, enabling you to create standard interface cables for use in interconnecting the scanner , scale, external handheld scanner , and POS terminal. General Specifications Wire Requirements • Cable length should not exceed 15 feet. • [...]

B-2 Magellan ® 9500 RS-232 Cable Pinout Scanner Connector Hardware RJ45, 10 P osition Cable Pinout Table B-1RS-232 Cable Pinouts PIN # FUNCTION DESCRIPTION 1 N/C No Connection 2 CTS in Clear T o Send (input) 3 N/C No Connection 4 RTS out Request T o Send (output) 5 RxD in Receive Data (Input) 6 TxD out T ransmit Data (output) 7 N/C No Connection 8[...]

RS-232 Cable Pinout — continued Product Reference Guide B-3 RS-232 Cable Pinout — continued Scale Connector Hardware RJ45, 10 P osition Cable Pinout Table B-2RS-232 Scale Cable Pinouts PIN # FUNCTION DESCRIPTION 1 +5V pullup +5V pullup 2 CTS IN Clear T o Send (input) 3 N/C No Connection 4 RTS OUT Request T o Send (output) 5 RxD IN Receiv e Data[...]

B-4 Magellan ® 9500 IBM Cable Pinout Scanner and Scale Connector Hardware RJ45, 10 P osition Cable Pinout Table B-3IBM Cable Pinouts PIN # FUNCTION DESCRIPTION 1 N/C No Connection 2 N/C No Connection 3 N/C No Connection 4 LINEB Line B 5 N/C No Connection 6 LINEA Line A 7 N/C No Connection 8 +5V out +5V out 9 GND Signal Ground 10 N/C No Connection[...]

IBM USB Cable Pinout Product Reference Guide B-5 IBM USB Cable Pinout Scanner and Scale Connector Hardware RJ45, 10 P osition Cable Pinout Table B-4IBM USB Cable Pinouts PIN # FUNCTION DESCRIPTION 1 N/C No Connection 2 N/C No Connection 3 N/C No Connection 4 USB D- USB D- 5 N/C No Connection 6 USB D+ USB D+ 7 N/C No Connection 8 +5V out +5V out 9 G[...]

B-6 Magellan ® 9500 Auxilliary Port External Handheld Input Connector Hardware RJ45, 10 P osition Cable Pinout Table B-5Auxilliary Port Cable Pinouts PIN # FUNCTION DESCRIPTION 1 +5V pullup +5V pullup 2 CTS in Clear T o Send (input) 3 N/C No Connection - Reser ved 4 R TS out Request T o Send (output) 5 RxD in Receive Data (Input) 6 TxD out T ransm[...]

Power Cable Product Reference Guide B-7 Power Cable Connector Hardware 6 pin M olex Cable Pinout Table B-6Power Cable Pinouts PIN # FUNCTION DESCRIPTION 1 EAR TH GND Ear th Ground 2 SIGNAL GND Signal Ground 3 +5V IN +5V in 4 N/C No Connection 5 N/C No Connection 6 +12V IN +12V in[...]

B-8 Magellan ® 9500 Remote Display Connector Hardware 4 pin SDL Cable Pinout Table B-7Remote Display Cable Pinouts PIN # FUNCTION DESCRIPTION 1 +12V OUT +12V out 2 LINE_A_DSPL Y LINE A Display 3 LINE_B_DSPL Y LINE B Display 4 GND Ground[...]

EAS Comm Port Product Reference Guide B-9 EAS Comm Port EAS Deactivator Control Box Connection Connector Hardware RJ10 Cable Pinout Table B-8EAS Comm Port Cable Pinouts PIN # FUNCTION DESCRIPTION 1 VCC5 VCC5 2 EAS DEACT EN~ EAS Deactivation 3 VCC5 VCC5 4 EAS DETECT EN~ EAS Detection 5 EAS LBL DETECT EN~ EAS tag Detect 6 GND Signal Ground 7 N/C No C[...]

B-10 Magellan ® 9500 NOTES[...]

Product Reference Guide C-1 Appendix C Keypad U se the bar codes in this appendix to enter numbers and characters as you would select digits/characters from a keypad. Scan your selection from the bar code s below . Y ou ’ll need to cover any unused bar codes on this and the faci ng page to ensure that the scanner reads only the bar code you inten[...]

C-2 Magellan ® 9500 U se the bar codes in this appendix to enter numbers and characters as you would select digits/characters from a keypad. Scan your selection from the bar code s below . Y ou ’ll need to cover any unused bar codes on this and the faci ng page to ensure that the scanner reads only the bar code you intend to scan. 2 3[...]

Product Reference Guide C-3 U se the bar codes in this appendix to enter numbers and characters as you would select digits/characters from a keypad. Scan your selection from the bar code s below . Y ou ’ll need to cover any unused bar codes on this and the faci ng page to ensure that the scanner reads only the bar code you intend to scan. 4 5[...]

C-4 Magellan ® 9500 U se the bar codes in this appendix to enter numbers and characters as you would select digits/characters from a keypad. Scan your selection from the bar code s below . Y ou ’ll need to cover any unused bar codes on this and the faci ng page to ensure that the scanner reads only the bar code you intend to scan. 6 7[...]

Product Reference Guide C-5 U se the bar codes in this appendix to enter numbers and characters as you would select digits/characters from a keypad. Scan your selection from the bar code s below . Y ou ’ll need to cover any unused bar codes on this and the faci ng page to ensure that the scanner reads only the bar code you intend to scan. 8 9[...]

C-6 Magellan ® 9500 U se the bar codes in this appendix to enter numbers and characters as you would select digits/characters from a keypad. Scan your selection from the bar code s below . Y ou ’ll need to cover any unused bar codes on this and the faci ng page to ensure that the scanner reads only the bar code you intend to scan. A B[...]

Product Reference Guide C-7 U se the bar codes in this appendix to enter numbers and characters as you would select digits/characters from a keypad. Scan your selection from the bar code s below . Y ou ’ll need to cover any unused bar codes on this and the faci ng page to ensure that the scanner reads only the bar code you intend to scan. C D[...]

C-8 Magellan ® 9500 U se the bar codes in this appendix to enter numbers and characters as you would select digits/characters from a keypad. Scan your selection from the bar code s below . Y ou ’ll need to cover any unused bar codes on this and the faci ng page to ensure that the scanner reads only the bar code you intend to scan. E F[...]

Product Reference Guide D-1 Appendix D Host Commands Accepting Commands from an RS-232 Scanner Host The scanner responds to the following RS-232 commands: If one of the above commands is r eceived, the scanner will perform the steps indicated for the command. Host commands for other interfaces is also available. Contact T ech Support for more detai[...]

D-2 Magellan ® 9500 NOTES[...]

Product Reference Guide E-1 Appendix E Factory Defaults The following table pro vides a listing of the most common factor y settings for the interfaces shown. Table E-1Factory Default Settings Aux RS-232 Wincor- Nixdorf Single Cable IBM 17 IBM USB Double Read Time- out 60 (600ms) 60 (600ms) 60 (600ms) 60 (600ms) 60 (600ms) 60 (600ms) Laser Timeout [...]

E-2 Magellan ® 9500 Good Read When to Indicate 1 (after transmit) 1 (after transmit) 1 (after transmit) 1 (after transmit) 1 (after transmit) 1 (after transmit) Scale Enable 0 (disable) 1 (enable) 0 (disable) 1 (enable) 1 (enable) 1 (enable) Scale Countr y Mode 0 (US) 0 (US) 0 (US) 0 (US) 0 (US) 0 (US) Scale Enf orced Zero Retur n 0 (disable) 0 (d[...]

Product Reference Guide E-3 EAS Deactivation Duration — Coupled 50 (500ms) 50 (500ms) 50 (500ms) 50 (500ms) 50 (500ms) 50 (500ms) EAS Deactivation Duration — Retry 50 (500ms) 50 (500ms) 50 (500ms) 50 (500ms) 50 (500ms) 50 (500ms) EAS Deactivation Duration — Manual 100 (5sec) 100 (5sec) 100 (5sec) 100 (5sec) 100 (5sec) 100 (5sec) Maximum Host-[...]

E-4 Magellan ® 9500 RS-232 Number of Stop Bits 0 (1 stop bit) 0 (1 stop bit) 0 (1 stop bit) 0 (1 stop bit) RS-232 P arity 0 (none) 0 (none) 2 (odd) 2 (odd) RS-232 Hardware Control 0 (disable) 0 (disable) 1 (enable CTS flow) RS-232 Intercharac- ter Dela y 0 (none) 0 (none) 0 (none) RS-232 Software Flow Control 0 (disable) 0 (disable) 0 (disable) 0 [...]

Product Reference Guide E-5 RS-232 Retr y on A CK NAK Timeout 1 (enable) 1 (enable) 1 (enable) RS-232 A CK NAK Timeout V alue 1 (200ms) 1 (200ms) 1 (200ms) RS-232 A CK NAK Retr y Count 3 resets 3 resets 3 resets RS-232 A CK NAK Error Handling 0 (ignore errors) 0 (ignore errors) 0 (ignore errors) RS-232 Label ID Control 1 (enable as prefix) 1 (enabl[...]

E-6 Magellan ® 9500 UPC-A Number Sys- tem Character T rans- mission 0 (disable) 1 (enable) 1 (enable) 1 (enable) 1 (enable) 1 (enable) UPC-A Check Char- acter T r ansmission 1 (enable) 1 (enable) 1 (enable) 0 (disable) 1 (enable) 1 (enable) Expand UPC-A to EAN-13 0 (disable) 0 (disable) 1 (enable) 0 (disable) 0 (disable) 0 (disable) UPC/EAN AIM ID[...]

Product Reference Guide E-7 UPC-E 128 Supple- mental Label ID 4500("E") 4500("E") 4300("C") 4500("E") EAN-13 Enable 1 (enable) 1 (enable) 1 (enable) 1 (enable) 1 (enable) 1 (enable) EAN-13 First Charac- ter T r ansmission 1 (enable) 1 (enable) 1 (enable) 1 (enable) 1 (enable) 1 (enable) EAN-13 Check Char- act[...]

E-8 Magellan ® 9500 EAN-8 128 Supple- mental Label ID 4646 ("FF") 4646 ("FF") 4200 ("B") 4646 ("FF") EAN-8 Decoding Le v- els 2 (Slightly More Aggresiv e) 2 (Slightly More Aggresiv e) 2 (Slightly More Aggresiv e) 2 (Slightly More Aggresiv e) 2 (Slightly More Aggresiv e) 2 (Slightly More Aggresiv e) UPC/EAN R[...]

Product Reference Guide E-9 RSS-14 Label ID 5234 ("R4") 5234 ("R4") 4500 ("E") 5234 ("R4") RSS Expanded Enable 0 (disab le) 0 (disable) 0 (disable) 0 (disable) 0 (disable) 0 (disable) RSS Expanded EAN- 128 Emulation 0 (disable) 0 (disable) 0 (disable) 0 (disable) 0 (disable) 0 (disable) RSS Expanded 2D Compon[...]

E-10 Magellan ® 9500 Code 39 Full ASCII 0 (disable) 0 (disable) 0 (disable) 0 (disable) 0 (disable) 0 (disable) Code 39 AIM ID 0 (disable) 0 (disable) 0 (disable) Code 39 Label ID 2A00 ("*") 2A00 ("*") 4D00 ("M") 4231 ("B1") Code 39 Length Con- trol 0 (variab le) 0 (variable) 0 (variable) 0 (variable) 0 (var[...]

Product Reference Guide E-11 Code 128 AIM ID 0 (disable) 0 (disable) 0 (disable) Code 128 Label ID 2300 ("#") 2300 ("#") 4B00 ("K") 4233 ("B3") Code 128 Length Control 0 (variable) 0 (variable) 0 (variable) 0 (variable) 0 (variable) 0 (variable) Code 128 Maximum Label Length 80 80 80 80 80 80 Code 128 Minimum[...]

E-12 Magellan ® 9500 I 2 of 5 Maximum Label Length 50 50 50 50 50 50 I 2 of 5 Minimum Label Length 666666 I 2 of 5 Fix ed Length 1 10 10 10 10 10 10 I 2 of 5 Fix ed Length 2 000000 I 2 of 5 Stitching 0 (disable) 0 (disable) 0 (disable) 0 (disable) 0 (disable) 0 (disable) Codabar Enable 0 (disable) 0 (disable) 0 (disable) 0 (disable) 0 (disable) 0 [...]

Product Reference Guide E-13 Codabar Fix ed Length 1 888888 Codabar Fix ed Length 2 14 14 14 14 14 14 Codabar Stitching 0 (disable) 0 (disable) 0 (disable) 0 (disable) 0 (disable) 0 (disable) Code 93 Enable 0 (disable) 0 (disable) 0 (disable) 0 (disable) 0 (disable) 0 (disable) Code 93 AIM ID 0 (disable) 0 (disable) 0 (disable) Code 93 Label ID 260[...]

E-14 Magellan ® 9500 MSI/Plessey Label ID 4000 ("@") 4000 ("@") 4F00 ("O") 4000 ("@") MSI/Plessey Length Control 0 (variab le) 0 (variable) 0 (variable) 0 (variable) MSI/Plessey Maxi- mum Label Length 16 16 16 16 MSI/Plessey Mini- mum Label Length 4444 MSI/Plessey Fix ed Length 1 7777 MSI/Plessey Fix ed Leng[...]

Product Reference Guide E-15 Standard 2 of 5 Mini- mum Label Length 666666 Standard 2 of 5 Fix ed Length 1 10 10 10 10 10 10 Standard 2 of 5 Fix ed Length 2 000000 Standard 2 of 5 Stitching 0 (disable) 0 (disable) 0 (disable) 0 (disable) 0 (disable) 0 (disable) Aux RS-232 Wincor- Nixdorf Single Cable IBM 17 IBM USB[...]

E-16 Magellan ® 9500 NOTES[...]

Product Reference Guide F-1 Appendix F Handheld Data Format Requirements This appendix pro vides application notes to describe the general format of data that can be accepted by the scanner through the auxilliary port as transmitted from a handheld scanner . Handheld Data Format Requirements General • 9600 bps, 8 data bits, 1 stop bit, no parity [...]

F-2 Magellan ® 9500 Datalogic Handheld Data Format Requirements The following sections describe label transmission formats that are typi- cally observed in factor y configurations of Datalogic handheld scanners. RSS-14 • P refix must be ASCII characters ‘R4’ • Check character must be included in label • Application identifier “01” mu[...]

Product Reference Guide F-3 UPC-A with 5-Digit Supplemental • N umber system must be included in label data • Check digit must be included in la bel data and is assumed to be cor- rect • P refix must be an ASCII character 'A' - total length including prefix must be 18 • Example: 'A06099201118712345' UPC-A with Code 128 S[...]

F-4 Magellan ® 9500 UPC-E with 2-Digit Supplemental • N umber system must be included in label data. • Check digit must be included in label data and is assumed to be cor- rect . • S upplemental data is appended to base label. • P refix must be an ASCII character 'E' - total length including prefix must be 11. • Example: '[...]

Product Reference Guide F-5 EAN-8 • Check digit must be included in la bel data and is assumed to be cor- rect • P refix must be an ASCII characters 'FF' - total length including pre- fix must be 10 • Example: 'FF00210126' EAN-8 with 2-Digit Supplemental • Check digit must be included in la bel data and is assumed to be [...]

F-6 Magellan ® 9500 EAN-13 • Check digit must be included in label data and is assumed to be cor- rect • P refix must be an ASCII character 'F'- total length including prefix must be 14 • Example: 'F1101234567891' EAN-13 with 2-Digit Supplemental • Check digit must be included in label data and is assumed to be cor- rec[...]

Product Reference Guide F-7 Code 39 • Check character must be included in label data. • Label length including start, stop and check characters and exclud- ing prefix character must meet requir ements imposed by the main scanner's fixed or variable label length control for this symbology type. • S tart and stop characters "*" m[...]

F-8 Magellan ® 9500 Codabar • Check character must be included in label data. • Label length including check char acter and excluding pr efix charac- ter must meet requirements imposed b y the main scanner's fixed or variable label length control for this symbology type. • P refix must be an ASCII character '%'. • S tart sto[...]

Product Reference Guide F-9 MSI/Plessey • Check character must be included in label data. • Label length including check char acter and excluding pr efix charac- ter must meet requirements impose d b y the main scanner's fixed or variable label length control for this symbology type. • P refix must be an ASCII character '@'. ?[...]

F-10 Magellan ® 9500 AIM Formats AIM specifies a 3-character string that is attached as a prefix to the label data for transmission. Because AIM specifies one identifier for UPC-A, UPC-E and EAN-13 labels, UPC-A, UPC-E and EAN-13 will be received from the handheld and transmitted by the scanner as EAN-13. The ']' character must be the fi[...]

Product Reference Guide F-11 2-Digit Supplemental • S upplemental data is appended to any EAN base label. • P refix must be ASCII characters ']E1'. • length of S upplemental data incl uding prefix must be 5. T otal required length is 21 for EAN-13 and 16 for EAN-8. • Examples: addon portion is highlighted data is underlined. 5-Dig[...]

F-12 Magellan ® 9500 Code 128 Supplemental • S upplemental data is appended to any EAN base label. • P refix must be ASCII characters ']C0'. • length of S upplemental data including prefix is variable but must be at least 9. • Examples: addon portion is highlighted data is underlined. Bookland • The 'Bookland' / ISBN [...]

Product Reference Guide F-13 Codabar • Check character must be included in label data. • Label length including check char acter and excluding pr efix charac- ters must meet requirements imposed b y the main scanner's fixed or variable label length control for this symbology type. • P refix must be ASCII characters ']F0'. • S[...]

F-14 Magellan ® 9500 RSS-14 • P refix must be ASCII characters ']e0'. • Check character must be included in label. • Label length excluding pr efix characters must be 14 characters. • Example: ']e001044123456789'. RSS Expanded • P refix must be ASCII characters ']e0'. • Label length excluding prefix charac[...]

Product Reference Guide F-15 Code 128 / EAN128 • P refix must be either ASCII characters ']C0', ']C1' or ']C2'. • Label length excluding prefix character must meet r equirements imposed by the main scanner's fixed or v ariable label length control for this symbology type. • If EAN-128 Symbology is Enabled an[...]

F-16 Magellan ® 9500 NOTES[...]

ASCII Character Set The table on this page shows a set of ASCII char acters and their corresponding H e x V alues. The Hex V alues in this table ar e needed for setting sy mbology specific label identifiers, as well as enabling custom prefix and suffix characters. Ta b l e 1 ASCII Char . Hex No . ASCII Char . Hex No . ASCII Char . Hex No . ASCII Ch[...]

Australia Datalogic Scanning Pty Ltd T elephone: [61] (2) 9870 3200 australia.scanning@datalogic.com France and Benelux Datalogic Scanning Sarl T elephone: [33].01.64.86.71.00 france.scanning@datalogic.com Germany Datalogic Scanning GmbH T elephone: 49 (0) 61 51/93 58-0 germany .scanning@datalogic.com India Datalogic Scanning India T elephone: 91- [...]