Dell M2800 инструкция обслуживания

Dell Precision M2800 Owner's Manual Regulatory Model: P29F Regulatory Type: P29F001[...]

Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. Copyright © 201[...]

Contents 1 Working on Your Computer................................................................................6 Before Working Inside Your Computer ................................................................................................ 6 Turning Off Your Computer ........................................................................[...]

Removing the Keyboard ..................................................................................................................... 26 Installing the Keyboard ........................................................................................................................ 27 Removing the Palmrest Assembly ............................[...]

6 Contacting Dell................................................................................................... 73[...]

1 Working on Your Computer Before Working Inside Your Computer Use the following safety guidelines to help protect your computer from potential damage and to help to ensure your personal safety. Unless otherwise noted, each procedure included in this document assumes that the following conditions exist: • You have read the safety information that[...]

3. If the computer is connected to a docking device (docked), undock it. CAUTION: To disconnect a network cable, first unplug the cable from your computer and then unplug the cable from the network device. 4. Disconnect all network cables from the computer. 5. Disconnect your computer and all attached devices from their electrical outlets. 6. Close[...]

2. Click the arrow in the lower-right corner of the Start menu as shown below, and then click Shut Down. . 2. Ensure that the computer and all attached devices are turned off. If your computer and attached devices did not automatically turn off when you shut down your operating system, press and hold the power button for about 4 seconds to turn the[...]

2 Removing and Installing Components This section provides detailed information on how to remove or install the components from your computer. Recommended Tools The procedures in this document may require the following tools: • Small flat-blade screwdriver • Phillips screwdriver • Small plastic scribe System Overview Figure 1. Back View — B[...]

5. ExpressCard slot 6. optical drive 7. coin-cell battery 8. base-corner cover (left) 9. WWAN card 10. WLAN card 11. docking port 12. battery bay 13. base-corner cover (right) Figure 2. Top View — Keyboard and Palmrest Assembly removed 1. WiFi-switch board 2. speaker 3. ExpressCard cage 4. system board 5. speaker 6. hard-drive bay 7. VGA board 8.[...]

Installing the Secure Digital (SD) Card 1. Slide the SD card into its slot until it clicks into place. 2. Follow the procedures in After Working Inside Your Computer . Removing the ExpressCard 1. Follow the procedures in Before Working Inside Your Computer . 2. Press in on the ExpressCard to release it from the computer. Slide the ExpressCard out o[...]

3. Flip the battery out of the computer. 12[...]

Installing the Battery 1. Slide the battery into its slot until it clicks into place. 2. Follow the procedures in After Working Inside Your Computer . Removing the Base Cover 1. Follow the procedures in Before Working Inside your computer . 2. Remove the screws that secure the base cover to the computer. 13[...]

3. Lift the base cover and remove it from the computer. 14[...]

Installing the Base Cover 1. Place the base cover to align with the screw holes on the computer. 2. Tighten the screws to secure the base cover to the computer. 3. Install the battery . 4. Follow the procedures in After Working Inside Your Computer . Removing the Base-Corner Covers 1. Follow the procedures in Before Working Inside your computer . 2[...]

5. Remove the screws that secure the right base-corner cover, lift and remove it from the computer. Installing the Base-Corner Covers 1. Place the left and right base-corner covers to align with the screw holes on the computer. 2. Tighten the screws to secure the base-corner covers to the computer. 3. Install: a. base cover b. battery 4. Follow the[...]

3. Pry the securing clips away from the memory module until it pops-up and remove the memory module from its connector on the system board. Installing the Memory 1. Insert the memory into the memory socket. 2. Press the securing clips to secure the memory module to the system board. 3. Install: a. base cover b. battery 4. Follow the procedures in A[...]

5. Flex the hard-drive isolation. Peel off the hard-drive isolation from the hard drive. Installing the Hard Drive 1. Install the hard-drive isolation on the hard drive. 2. Attach the hard-drive caddy to the hard drive. 3. Tighten the screws to secure the hard-drive caddy to the hard drive. 4. Slide the hard drive into the computer. 5. Tighten the [...]

4. Remove the screw that secures the optical-drive latch to the optical drive. Slide the optical-drive latch and remove it from the optical-drive. 5. Remove the screws that secure the optical-drive latch bracket to the optical drive. Remove the latch bracket from the optical drive. Installing the Optical Drive 1. Align the optical-drive latch brack[...]

5. Slide the optical drive into the drive bay. 6. Press the optical-drive latch to secure the optical drive. 7. Install the battery . 8. Follow the procedures in After Working Inside Your Computer . Removing the Wireless Local Area Network (WLAN) Card 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove: a. battery b. base co[...]

Installing the WWAN Card 1. Place the WWAN card in its slot in the system board. 2. Press the WWAN card down and tighten the screw to secure the WWAN card to the computer. 3. Connect the antenna cables to their connectors on the WWAN card. 4. Install: a. base cover b. battery 5. Follow the procedures in After Working Inside Your Computer . Removing[...]

Installing the Network Connector 1. Align the network connector to its position on the computer. 2. Place the network-connector bracket on the network connector. 3. Tighten the screw to secure the network-connector bracket to the computer. 4. Route the cable through the routing channel. 5. Connect the cable to the system board. 6. Install: a. base-[...]

Installing the Coin-Cell Battery 1. Place the coin-cell battery in its slot. 2. Connect the coin-cell battery cable to the system board. 3. Install: a. base cover b. battery 4. Follow the procedures in After Working Inside Your Computer . Removing the Power Connector 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove: a. ba[...]

Installing the Power Connector 1. Align the power connector to its position in the computer. 2. Place the power-connector bracket on the power connector. 3. Tighten the screw to secure the power-connector bracket to the computer. 4. Route the cable through the routing channel. 5. Connect the cable to the system board. 6. Install: a. base cover b. b[...]

4. Perform the following steps as shown in the illustration: a. Slide the heat-sink assembly. b. Lift the heat-sink assembly from the computer. Installing the Heat-Sink Assembly 1. Slide the heat-sink assembly to its position on the system board. 2. Tighten the screws to secure the heat-sink assembly to the system board. 3. Connect the fan cable to[...]

Installing the Processor 1. Align the notches on the processor and the socket, and insert the processor into the socket. 2. Rotate the processor-cam lock in a clockwise direction. 3. Install: a. heatsink b. base cover c. battery 4. Follow the procedures in After Working Inside Your Computer . Removing the Keyboard 1. Follow the procedures in Before[...]

5. Flip the keyboard and disconnect the keyboard cable from the system board. Installing the Keyboard 1. Connect the keyboard cable to the system board. 2. Place the keyboard to align with the screw holders on the computer. 3. Tighten the screws to secure the keyboard to the palmrest assembly. 4. Insert the keyboard trim on the keyboard and press a[...]

f. base cover g. base-corner covers 3. Remove the screws that secure the palmrest assembly to the base of the computer. 4. Flip the computer and remove the screws that secure the palmrest assembly to the computer. 28[...]

5. Disconnect the following cables: a. fingerprint-reader b. touchpad c. power-button 29[...]

6. Pry the palmrest assembly upwards and remove it from the computer. 30[...]

Installing the Palmrest Assembly 1. Align the palmrest assembly to its original position in the computer and snap it into place. 2. Tighten the screws to secure the palmrest assembly to the computer. 3. Connect the following cables: a. power-button b. touchpad c. fingerprint-reader 4. Flip the computer and tighten the screws to secure the palmrest [...]

Removing the WiFi-Switch Board 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove: a. SD card b. ExpressCard c. battery d. keyboard e. display-hinge cap f. base cover g. base-corner covers h. palmrest assembly 3. Perform the following steps as shown in the illustration: a. Disconnect the cable from the system board. b. Remo[...]

Removing the VGA Board 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove: a. SD card b. ExpressCard c. battery d. keyboard e. display-hinge cap f. base cover g. base-corner covers h. palmrest assembly 3. Remove the screws that secure the VGA board to the computer and remove it from its connector. Installing the VGA Board 1[...]

b. ExpressCard c. battery d. keyboard e. display-hinge cap f. base cover g. base-corner covers h. Palmrest Assembly 3. Remove the screws that secure the ExpressCard cage to the computer. Remove the ExpressCard cage from the computer. Installing the ExpressCard Cage 1. Place the ExpressCard cage in its slot. 2. Tighten the screws to secure the Expre[...]

g. display-hinge cap h. base cover i. base-corner covers j. power connector k. coin cell l. memory m. WLAN card n. WWAN card o. heatsink p. processor q. VGA board r. ExpressCard cage 3. Perform the following steps as shown in the illustration: a. Disconnect the WiFi-switch from the system board. b. Disconnect the speaker cables from the system boar[...]

5. Lift the system board from the computer. 36[...]

Installing the System Board 1. Place the system board to align with the ports on the computer. 2. Tighten the screws to secure the system board. 3. Connect the following cables to the system board: a. speaker b. WiFi-switch 4. Install: a. ExpressCard cage b. VGA board c. processor d. heatsink e. WWAN card f. WLAN card g. memory h. coin-cell battery[...]

n. hard drive o. keyboard p. battery q. ExpressCard r. SD card 5. Follow the procedures in After Working Inside Your Computer . Removing the Speakers 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove: a. SD card b. ExpressCard c. battery d. keyboard e. hard drive f. optical drive g. display-hinge cap h. base cover i. base-[...]

4. Lift the speakers from the computer. 39[...]

Installing the Speakers 1. Align the speakers in its position on the computer and route the speaker cable in the routing channels on the computer. 2. Tighten the screws to secure the speakers. 3. Install: a. system board b. ExpressCard cage c. VGA board d. processor e. heatsink f. WWAN card g. WLAN card h. memory i. coin-cell battery j. power conne[...]

p. hard drive q. keyboard r. battery s. ExpressCard t. SD card 4. Follow the procedures in After Working Inside Your Computer . Removing the Display-Hinge Cap 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the battery . 3. Remove the screws that secure the display-hinge cap to the computer and remove the display-hinge c[...]

4. Disconnect the LVDS cable and release the LVDS cable and camera cable from the routing channel. Remove them from the computer. 42[...]

5. Remove the screws that secure the display assembly to the computer. 43[...]

6. Remove the display assembly from the computer. 44[...]

Installing the Display Assembly 1. Place the display assembly in its position on the computer. 2. Tighten the screws to secure the display assembly. 3. Route the LVDS cable and the camera cable through the routing channel. 4. Route the antenna cables through the routing channel. 5. Connect the antenna cables to the WLAN card on the computer. 6. Con[...]

b. display-hinge cap c. base cover d. base-corner covers e. display assembly 3. Pry up along the edges to release the display bezel. 4. Remove the display bezel from the display assembly. 46[...]

Installing the Display Bezel 1. Place the display bezel onto the display assembly. 2. Starting from the top corner, press on the display bezel and work around the entire bezel until it clicks onto the display assembly. 3. Press on the left and right edges of the display bezel. 4. Install: a. display assembly b. base-corner covers c. base cover d. d[...]

f. display bezel 3. Remove the screws that secure the display panel to the display assembly. 4. Flip the display panel over. 48[...]

5. Peel off the LVDS cable-connector tape and disconnect the LVDS cable from the display panel. Remove the display panel from the display assembly. 49[...]

Installing the Display Panel 1. Connect the LVDS cable and stick the LVDS cable-connector tape. 2. Flip the display and place it in the display assembly. 3. Tighten the screws to secure the display panel to the display assembly. 4. Install: a. display bezel b. display assembly c. base-corner covers d. base cover e. display-hinge cap f. battery 5. F[...]

f. display bezel g. display panel 3. Perform the following steps as shown in the illustration: a. Remove the screws that secure the display hinges to the display assembly. b. Remove the display hinges from the computer. Installing the Display Hinges 1. Place the display hinges in its location on the computer. 2. Tighten the screws to secure the dis[...]

Installing the Camera 1. Place the camera module in its slot in the computer. 2. Tighten the screw to secure the camera to the display assembly. 3. Connect the camera cable. 4. Install: a. display bezel b. display assembly c. battery 5. Follow the procedures in After Working Inside Your Computer . 52[...]

3 System Setup System Setup enables you to manage your computer hardware and specify BIOS ‐ level options. From the System Setup, you can: • Change the NVRAM settings after you add or remove hardware • View the system hardware configuration • Enable or disable integrated devices • Set performance and power management thresholds • Manage[...]

Table 1. Navigation Keys Keys Navigation Up arrow Moves to the previous field. Down arrow Moves to the next field. <Enter> Allows you to select a value in the selected field (if applicable) or follow the link in the field. Spacebar Expands or collapses a drop ‐ down list, if applicable. <Tab> Moves to the next focus area. NOTE: For th[...]

Option Description Advanced Boot Options Allows you to configure your system for legacy boot mode. The option is enables by default. Date/Time Allows you to set the date and time. Table 3. System Configuration Option Description Integrated NIC Allows you to configure the integrated network controller. The options are: • Disabled • Enabled • E[...]

Option Description • SATA-4 • SATA-5 Default Setting: All drives are enabled. SMART Reporting This field controls if the hard drive errors for the integrated drives are reported during system startup. This technology is part of the SMART (Self Monitoring Analysis and Reporting Technology) specification. This option is disabled by default. • E[...]

Option Description • Enable Hard Drive Free Fall Protection Default Setting: All devices are enabled You can select if you want to enable or disable media card. The options are: • Enable Media Card (Default Setting) • Disable Media Card Table 4. Video Option Description LCD Brightness Allows you to set the panel brightness when the ambient se[...]

Option Description Non-Admin Setup Changes Allows you to determine whether changes to setup option are permitted when an administrator password is set. The option is disabled by default. TPM Security Allows you to enable the Trusted Platform Module (TPM) during POST. The option is disabled by default. Computrace Allows you to activate or disable th[...]

Option Description Default Setting: Enable Intel SpeedStep C States Control Allows you to enable or disable the additional processor sleep states. The option is enabled by default. Limit CPUID Allows you to limit the maximum value the processor standard CPUID function will support. The option is disabled by default. Intel TurboBoost Allows you to e[...]

Option Description Wake on LAN/WLAN This option allows the computer to power up from the off state when triggered by a special LAN signal. Wake-up from the Standby state is unaffected by this setting and must be enabled in the operating system. This feature only works when the computer is connected to AC power supply. • Disabled - Does not allow [...]

Option Description • Enable Adapter Warnings Mouse/Touchpad Allows you to define how the computer handles the mouse and touchpad input. The options are: • Serial Mouse • PS2 Mouse • Touchpad/PS-2 Mouse (Default Setting) Numlock Enable Specifies if the NumLock function can be enabled when the computer boots. This option is enabled by default[...]

Option Description NOTE: The TPM , Virtualization Technology , and Virtualization Technology for Direct I/O must be enabled to use this feature. Table 11. Wireless Option Description Wireless Switch Allows you to determine which wireless device can be controlled by the wireless switch. The options are: • WWAN • WiGig • WLAN • Bluetooth All [...]

NOTE: If you cannot find your Service Tag, click Detect My Product . Proceed with the instructions on screen. 4. If you are unable to locate or find the Service Tag, click the Product Category of your computer. 5. Choose the Product Type from the list. 6. Select your computer model and the Product Support page of your computer appears. 7. Click Get[...]

Use the following guidelines to assign the system password: • A password can have up to 32 characters. • The password can contain the numbers 0 through 9. • Only lower case letters are valid, upper case letters are not allowed. • Only the following special characters are allowed: space, (”), (+), (,), (-), (.), (/), (;), ([), (), (]), (`[...]

4 Diagnostics If you experience a problem with your computer, run the ePSA diagnostics before contacting Dell for technical assistance. The purpose of running diagnostics is to test your computer's hardware without requiring additional equipment or risking data loss. If you are unable to fix the problem yourself, service and support personnel [...]

Device Status Lights Table 14. Device Status Lights Turns on when you turn on the computer and blinks when the computer is in a power management mode. Turns on when the computer reads or writes data. Turns on steadily or blinks to indicate battery charge status. Turns on when wireless networking is enabled. The device status LEDs are usually locate[...]

Alternately blinking amber light and white light An unauthenticated or unsupported non-Dell AC adapter is attached to your laptop. Alternately blinking amber light with steady white light Temporary battery failure with AC adapter present. Constantly blinking amber light Fatal battery failure with AC adapter present. Light off Battery in full charge[...]

5 Technical Specifications NOTE: Offerings may vary by region. The following specifications are only those required by law to ship with your computer. For more information about the configuration of your computer, go to Help and Support in your Windows operating system and select the option to view information about your computer. Table 16. System [...]

Feature Specification Internal high-definition audio External microphone-in, stereo headphones, external speakers connector Speakers two Internal speaker amplifier 1 W (RMS) per channel Volume controls hot keys Table 20. Video Feature Specification Type integrated on system board Controller: UMA Intel HD Graphics 4600 Discrete AMD FirePro W4170M Da[...]

Features Specification USB Four USB 3.0-compliant connectors Memory card reader Support upto SD 4.0 Micro Subscriber Identity Module (uSIM) card one Docking port one Table 24. Contactless Smart Card Feature Specification Supported Smart Cards/Technologies BTO with USH Table 25. Display Feature Specification Type FHD Anti-Glare HD Anti-Glare Dimensi[...]

Feature Specification Y-axis 45.00 mm Table 28. Battery Feature Specification Type 6 cell (65 Whr) lithium ion 9 cell (97 Whr) lithium ion Dimensions: Depth 48.08 mm (1.89 inches) 71.79 mm (2.83 inches) Height 20.00 mm (0.79 inches) 20.00 mm (0.79 inches) Width 208.00 mm (8.19 inches) 214.00 mm (8.43 inches) Weight 345.00 g (0.76 lb) 524.00 g (1.16[...]

Feature Specification Weight 2.36 kg (5.21 lb) Table 31. Environmental Feature Specification Temperature: Operating 0 °C to 35 °C (32 °F to 95 °F) Storage –40 °C to 65 °C (–40 °F to 149 °F) Relative humidity (maximum): Operating 10 % to 90 % (non condensing) Storage 5 % to 95 % (non condensing) Altitude (maximum): Operating –15.2 m to[...]

6 Contacting Dell NOTE: If you do not have an active Internet connection, you can find contact information on your purchase invoice, packing slip, bill, or Dell product catalog. Dell provides several online and telephone-based support and service options. Availability varies by country and product, and some services may not be available in your are[...]