Delta 17-900 инструкция обслуживания

INSTRUCTION MANUAL 16½" Floor Model Drill Pr ess (Model 17-900) P ART NO. 900603 (011) Copyright © 2001 Delta Machinery ESP AÑOL: PÁGINA 17 T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Canada call 1-800-463-3582).[...]

2 SAFETY RULES W oodworking can be dangerous if safe and pr oper operating procedures ar e not followed. As with all machinery , there are certain hazar ds involved with the operation of the product. Using the machine with respect and caution will considerably lessen the possibility of personal injury . However , if normal safety precautions are ov[...]

3 1. DO NOT operate your tool until it is completely assembled and installed according to the instructions. 2. IF YOU ARE NOT thoroughly familiar with the operation of drill presses, obtain advice fr om your supervisor , instructor or other qualified person. 3. YOUR TOOL MUST be securely fastened to a stand or workbench. If there is any tendency fo[...]

4 UNP ACKING AND CLEANING Carefully unpack the drill pr ess and all loose items from the shipping container(s). Remove the protective coating fr om the machined surfaces of the drill press. This coating may be r emoved with a soft cloth moistened with kerosene. Do not use acetone, gasoline or lacquer thinner for this purpose. Figs. 2 and 3 illustra[...]

5 ASSEMBL Y Fig. 4 Fig. 6 2. Insert table (G) Fig. 5, into table mounting bracket (E) and tighten lever (D) to lock table in position. Tighten locking lever (F) Fig. 5, to lock table raising mechanism on the column. 3. Assemble table raising and lowering handle (H) Fig. 5, to table mounting bracket (E). Align the set screw on handle (H) with the fl[...]

6 Fig. 7 Fig. 8 Fig. 9 5. Thread the three pinion shaft handles (N) Fig. 7, into the three holes in the pinion shaft (P) as shown. 6. IMPORT ANT : Make certain the tapered hole in the bottom of spindle (T) Fig. 8, and the taper on spindle adapter (U) are clean and fr ee of any grease, lacquer or rust preventive coatings. NOTE: If necessary , househ[...]

7 F ASTENING DRILL PRESS BASE TO A SUPPOR TING SURF ACE PERMANENT MOUNTING If your drill press is to be used in one permanent location, the drill pr ess base must be secured to the supporting surface with fasteners through the two mounting holes, (A) Fig. 10, in the drill press base. MOUNTING DRILL PRESS TO A PL YWOOD BASE If you do not fasten your[...]

8 CONNECTING TOOL TO POWER SOURCE POWER CONNECTIONS A separate grounded electrical cir cuit should be used for your tool. This circuit should not be less than #12 wir e and should be protected with a 20 amp fuse or cir cuit breaker . Before connecting the tool to the power line, make sur e the switch is in the “OFF” position. If the power cord [...]

9 GROUNDED OUTLET BOX CURRENT CARR YING PRONGS GROUNDING BLADE IS LONGEST OF THE 3 BLADES Fig. 15 240 VOL T OPERA TION Y our drill press may be converted for 240 volt operation. The conversion of your drill press for 240 volt operation must be done by qualified electrical personnel. Should you desire to have your drill pr ess converted for 240 volt[...]

10 Fig. 17 Fig. 18 ST AR TING AND STOPPING DRILL PRESS The switch (A) Fig. 17, is located on the front of the drill press head. T o turn the drill press “ON” move the switch to the up position. T o tur n the drill press “OFF” move the switch to the down position. LOCKING SWITCH IN THE “OFF” POSITION When the tool is not in use, the swit[...]

11 Fig. 21 Fig. 22 4. Fig. 21, illustrates the table alignment pin (B) removed. Loosen table locking bolt (D) Fig. 21, tilt table to the desired angle and tighten bolt (D). When r etur ning table to the level position, replace table alignment pin (B). This will automatically position the table surface at 90 degrees to the spindle. 5. A tilt scale ([...]

12 Fig. 26 DRILLING HOLES TO DEPTH When a number of holes are to be drilled to exactly the same depth, a depth stop is provided in the pinion shaft housing and is used as follows: 1. Loosen lock screw (A) Fig. 26, and r otate housing (B) until the pointer (C) lines up with the desired depth indicated on scale (D). Then tighten lock screw (A). 2. Al[...]

13 Fig. 27 Fig. 28 ADJUSTING SPINDLE RETURN SPRING The spindle is automatically returned to its upper most position upon release of the handle. It is r ecommended that the handle be allowed to slowly return to the top position after all holes have been drilled in the material. This spring has been properly adjusted at the factory and should not be [...]

14 BORING IN WOOD T wist drills, although intended for metal drilling, may also be used for boring holes in wood. However , machine spur bits are generally pr eferred for working in wood; they cut a square bottom hole and ar e designed for removal of woodchips. Do not use hand bits which have a scr ew tip; at drill press speeds they turn into the w[...]

15 NOTES[...]

16 Delta Building T rades and Home Shop Machinery T wo Y ear Limited W arranty Delta will repair or r eplace, at its expense and at its option, any Delta machine, machine part, or machine accessory which in normal use has proven to be defective in workmanship or material, pr ovided that the customer returns the product pr epaid to a Delta factory s[...]