Delta 50-861 инструкция обслуживания

INSTRUCTION MANUAL 5 H.P . Dust Collector (Model 50-866 Single Phase) (Model 50-861 Thr ee Phase) P ART NO. 902110 - 04-18-02 Copyright © 2002 Delta Machinery T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Canada call 1-800-4[...]

2 GENERAL SAFETY RULES W oodworking can be dangerous if safe and pr oper operating procedures ar e not followed. As with all machinery , ther e are certain hazar ds involved with the operation of the product. Using the machine with r espect and caution will considerably lessen the possibility of personal injury . However , if normal safety precauti[...]

3 IMPOR T ANT SAFETY RULES FOR DUST COLLECTORS W ARNING: Basic precautions should always be followed when using your dust collector . T o reduce the risk of injury , electrical shock or fire, comply with the safety rules listed below: 1. DO NOT leave the dust collector plugged into the electrical outlet. Unplug dust collector from the outlet when n[...]

4 UNP ACKING AND CLEANING Carefully unpack the tool and all loose items fr om the shipping container(s). Remove the protective coating fr om all unpainted surfaces. This coating may be removed with a soft cloth moistened wi th ke r osene (do not use acetone, gasoline or lacquer thinner for this purpose). After cleaning, cover the unpainted surfaces[...]

5 Fig. 3 Fig. 4 1. Motor , Fan and Blower Assembly (Hardwar e for mounting not shown: 5/16" flat washer (4), 5/16" lockwasher (4), 5/16-18 hex nut (4) 2. Drums (2) 3. Gaskets (2) 4. Switch Control Box for Model 50-866 only .( 3 sheet metal screws for mounting) 5. Hardwar e for Mounting Drums to Fan and Blower Assembly Includes: 5/16-18 x [...]

6 ASSEMBL Y ASSEMBLING CASTERS TO BASE T ur n base over . Align four holes in caster (A) Fig. 5, with four holes at one corner of base (B) and assemble caster to base. Place a 5/16" lockwasher (D), then a 5/16" flat washer (E) on a 5/16-18x5/8" hex head screw (C), insert the hex head screw thr ough the hole in the wheel caster and th[...]

7 Fig. 10 Fig. 11 Fig. 12 Fig. 14 Fig. 13 4. NOTE: FOR MODEL 50-866 MAKE SURE THA T THE FRONT OF THE MOTOR ASSEMBL Y IS A TT ACHED TO THE SUPPORT WITH THREE PREDRILLED HOLES IN IT , (THESE HOLES ARE WHERE THE CONTROL BOX IS TO BE MOUNTED). Carefully place the motor/blower assembly (F) Fig. 10, onto two side supports (A), which were assembled in STE[...]

8 Fig. 15 Fig. 16 Fig. 17 Fig. 18 9. Fig. 15, illustrates both drums (K) assembled to the fan and blower assembly (F). ASSEMBLING DRUM SUPPOR T POSTS TO BASE AND DRUMS 1. Assemble end of drum support post (A) Fig. 16, to threaded holes in one corner of base (B). Place a 5/16" lockwasher (C), on a 5/16-18 x 5/8" hex head screw (D), insert [...]

9 Fig. 19 Fig. 20 Fig. 21 Fig. 22 ASSEMBLING INT AKE PORT TO MOTOR AND BLOWER ASSEMBL Y Place the intake port (A) Fig. 19, onto the flange of motor/blower assembly (B). Align the holes in the flange (B) of the motor/blower assembly with the mounting holes in the dust intake port and fasten with four sheet metal screws (C) as shown in Fig. 20. WARNI[...]

10 Fig. 23 Fig. 24 Fig. 25 Fig. 26 3. Assemble six-position filter bag hanger assembly (G) Fig. 23, to the top half of the upper bag support (H). Place a 5/16" lockwasher (I) onto a 5/16-18x1¼" hex head screw (J), place a special washer (K) (30mm O.D., 8mm I.D., 3mm thick), onto the screw , insert the screw through the filter bag hanger [...]

11 Fig. 27 Fig. 28 Fig. 29 ASSEMBLING DUST COLLECTION BAGS TO DRUMS 1. Insert bag clamp (A) Fig. 27, through the loops of the dust bag (B). 3. Clamp the dust collection bag (B) Fig. 29, around drum (C) with the locking band (F). Assemble the remaining dust collection bag to the drum at the other side of the dust collector . NOTE: Make certain locki[...]

12 Fig. 32 CONNECTING MACHINE TO POWER SOURCE MODEL 50-866 SINGLE PHASE INST ALLA TION WARNING: Installation by a qualified electrician is recommended to assur e safe and proper wiring and product operation. The motor rating for your single phase dust collector is 230 V olts, 5 H.P . Before connecting your dust collector to an electrical power syst[...]

13 Fig. 34 Fig. 35 MODEL 50-861 THREE PHASE INST ALLA TION WARNING: Installation by a qualified electrician is recommended to assur e safe and proper wiring and product operation. The motor rating for your three phase dust collector is 200-2 20/440 V olts, 5 H.P . Unless ordered special, the mac hin e is shipped wired for 200-220 V olts. Before con[...]

14 MAINTENANCE NOTE: Before any maintenance or service is performed, be sur e that unit is disconnected from power sour ce to prevent accidental starting. MOTOR MAINTENANCE Removing dust and dirt: Blow off motor with low pressur e air to remove dust or dirt. Air pr essure above 50 P .S.I. should not be used, as high pressur e may damage insulation [...]

15 ACCESSORIES A complete line of accessories is available from your Delta Supplier , Porter -Cable · Delta Factory Service Centers, and Delta Authorized Service Stations. Please visit our W eb Site www .deltamachinery .com for a catalog or for the name of your nearest supplier . WARNING: Since accessories other than those of fered by Delta have n[...]

The following are trademarks of POR TER-CABLE · DEL T A (Las siguientes son marcas r egistradas de PORTER-CABLE S.A.): BAMMER ® , INNOV A TION THA T WORKS ® , JETSTREAM ® , LASERLOC ® , OMNIJIG ® , POCKET CUTTER ® , PORT A-BAND ® , PORT A-PLANE ® , PORTER- CABLE ® , QUICKSAND ® , SANDTRAP ® , SA W BOSS ® , SPEED-BLOC ® , SPEEDMA TIC ?[...]