Desa DVF32TMHST инструкция обслуживания

This fireplace is manufactured for Stylecrest Inc. under the Coleman brand nam e by DESA International Inc. DESA INTERNATIONAL 2701 INDUSTRIAL DRIVE P/N 56088 P.O. BOX 90024 REV E BOWLING GREEN, KY 42101-9004 10/02 www.desatech.com SAVE THIS BOOK This book is valuable. In addition to inst ructing you on how to install and ma intain y our appliance,[...]

- 1 - For more information, visit www.desatech.com CONTENTS 1. INTRODUCTION PG. 2 2. SELECTING LOCATION PG. 2 3. MINIMUM CLEARA NCES PG. 2-3 4. VENT PIPE AND TERM. CLEARANCES PG. 4-5 5. VENTING INSTRUCTIONS PG. 5 6. FRAMING PG. 6 7. GAS SUPPLY TESTING AND HOOK-UP PG. 7 8. PILOT ADJUSTMENT PG. 8 9. SPECIFICATION TABLE PG. 8 10. LOG INSTALLATION PG. [...]

-2 - For more information, visit www.desatech.com INTRODUCTION Models DVF32TMHST (with fan) and DVF32TMHST-1 (without fan) are heat circulating gravity direct vent gas fireplaces with sealed combusti on cham ber. These fireplaces use a millivolt gas control valv e and millivolt ignition system. These fireplaces are convertible with the standard set[...]

-3 - For more information, visit www.desatech.com MANTEL CLEARANCES Woodwork, such as wood trims, m antels and other combustible ma terials should be placed within the required clearance specified on figures 3 and 4. VENT TERMINATION CLEARANCES The final position of your fire place depends on the location of the vent termination in relation to the [...]

-4 - For more information, visit www.desatech.com VENT PIPE AND TERMINATION CLEARANCES The final position of your appl iance depends on the location of th e term ination in relation to the clearances that must be obse rved. A= 12” (305mm ) clearance above grade, veranda, porch, deck or balcony. *** B= 9” (229mm) clearance in U.S. and 12” (305[...]

-5 - For more information, visit www.desatech.com VENT INSTALLATION INSTRUCTIONS 1. Install pipe to fireplace collar adapter located on back of unit at a 45 deg. Angle. Connect our starting pipe to a 45 deg. Starting section by sliding it over the collar adapter on the fireplace. Twist-lock for proper installation check t o insure proper connection[...]

-6 - For more information, visit www.desatech.com Refer to the following table fo r clearance between roof and termination. FRAMING Once the final location has been determ ined (observing clearances for vent terminati on), you may construct fram ing using dime nsions shown in figures 10 through 12, dependi ng on the particular installatio n. If the[...]

-7 - For more information, visit www.desatech.com The remote control receiver is c onnected to the convertible gas valve as shown in figure 14. GAS SUPPLY TESTING NOTE : This section is intended as a guide for quali fied technicians installing g as to the appliance. The appliance and its individual shut-off valve must be disconnected from the gas s[...]

-8 - For more information, visit www.desatech.com Install a sediment trap between the incoming gas line and the gas control box (see figure 18). The sedim ent trap should extend down a mini mum of 3 i nches (76 mm) bey ond the center of the pipe. When routing gas line through conduit sl eeve, make sure to repack insulation to fill gaps between gas [...]

- 9 - For more information, visit www.desatech.com LOG SET INSTALLATION Before proceeding, make sure th e gas control valve is in the “OFF” position. Logs have been packaged separately to prevent damage to glass or refract ory. 1. Remove top and bottom louve rs by simultaneously pulling both top end spring latc hes towards the center of the app[...]

- 10 - For more information, visit www.desatech.com 9. Place logs “B” as shown in Figures 25 and 26. Lift the propped up end of log “A” that is propped up and place log “B” under it. At the same time, the ot her side of log “B” is placed over the other log “A”. Re peat procedure for the other log “B”. 10. Take twigs “C” [...]

- 11 - For more information, visit www.desatech.com BURNER FLAME ADJUSTMENT The air shutter is located at t he underside of the main burner (There are two (2) air shutters on the Propane gas versions). All have been factory preset to the proper ai r-to gas ratio which results in an even, clean burning flame across the burner (See Figure 31). If rea[...]

- 12 - For more information, visit www.desatech.com DECORATIVE FACING Any non-combustible material m ay be used for facing (glass, tile, brick, etc.) as long as the proper clearances are observed (Refer to the section on Clearances). Louvered openings must not be obstructed, and upper a nd lower panels must remai n removable for servicing. Use only[...]

- 13 - For more information, visit www.desatech.com[...]

- 14 - For more information, visit www.desatech.com ACCESORY AND REPLACEMENT PARTS[...]

- 15 - For more information, visit www.desatech.com WIRING DIAGRAM[...]

- 16 - For more information, visit www.desatech.com OBSERVED PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION • Pilot will not stay lit after carefully following ligh ting instructions. • Pilot lit bu t no flame on the burner. • Frequent pilot outage problem. • Defective pilot g enerator (thermocouple). • Remote or wires defective. • Thermopile[...]

- 17 - For more information, visit www.desatech.com Read these instructions completely before installing this conversion kit. Before pro ceeding, m ake sure the gas control valve i s on the "OFF" position, all electrical power to the a ppliance is OFF, and the fireplace is cool to the touch. Conversion Kit m odel PC- DVF32TMHSTPN is requi[...]

- 18 - For more information, visit www.desatech.com DISASSEMBLING THE HEARTH AND BURNER SYSTEM 1. Remove the grate with the logs left in place, by lifting th e grate portion off of its stands and place the entire assembly o utside of the unit for ease of reassembly. (Refer to figure 34 Disassem b ly of Hearth System ) 2. Remove the two 5/16" h[...]

- 19 - For more information, visit www.desatech.com REINSTALLING THE MAIN BURNER Reinstall the heart h pan by sliding the end flange over the bo ttom edge of the refractory stand then center and slide the fron t edge down between the raised hearth support. Rei nsert the two side bricks in reverse order then center t he view port in the hearth pan o[...]

- 20 - For more information, visit www.desatech.com FINAL PREPARATION 1. Place the grate and log asse mbly back into position on the grate stand as shown in your appliance Installati on Manual. 2. Close the glass door and tightly secure all four l atches. 3. Replace the screen rod assembly and then the top and bottom louver assem blies with the lou[...]