DeWalt D26204K инструкция обслуживания

D26204- XE HEA VY -DUTY COMP ACT ROUTER INSTRUCTION MANU AL[...]

[...]

1 Definitions: Safety Guidelines The definitions below describe the level of severity for each signal word. Please read the manual and pay attention to these symbols. DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury . WARNING: Indicates a potentially hazardous situation which, if not [...]

2 WARNING: T o reduce the risk of injur y , user must read the instr uction manual. GENERAL POWER TOOL SAFETY WARNINGS WARNING! R ead all safety warnings and all instructions Failure to follow the warnings and instr uctions may result in electric shock, fire and/or serious injur y . The term “power tool” in the war nings refers to your mains-op[...]

3 b) Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. c) Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive sa[...]

4 • Hearing protection: AS/NZS1270 Acoustics – Hearing Protection; • Respiratory protection: AS/NZS1716 Respirator y Protective Devices. WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other constr uction activities contains chemicals known to cause cancer , bir th defects or other reproductive harm. Some examples[...]

5 A E D F C B G L J Q FIG. 1 ROUND SUBBASE D-SUBBASE I K H FIXED BASE M N O P R PL UNGE BASE[...]

6 .............. Class II Constr uction .............ear thing terminal ................... (double insulated) ..............safety aler t symbol …/min ........ per minute BPM ..........beats per minute IPM ............. impacts per minute RPM ..........revolutions per minute SPM ............ strokes per minute sfpm ..........sur face feet per mi[...]

7 Cutter Installation and Removal (Fig. 1, 3) WARNING: T o reduce the risk of injury , turn unit off and disconnect it from power source before installing and removing accessories, before adjusting or when making repairs. An accidental star t-up can cause injur y . TO INST ALL THE CUTTER 1. Remove the motor unit (J) from the base unit. Refer to Mot[...]

8 Excessive force should not be used to clamp the locking lever . Using excessive force may damage the fixed base. When the locking lever (I) is clamped the motor (J) should not move in the fixed base. Adjustment is needed if the locking lever will not clamp without excessive force or if the motor moves in the fixed base af ter clamping. TO ADJUST [...]

9 5. While holding down on the cone, tighten the subbase screws. LL LL T FIG. 6A FIXED BASE FIG 6B LL LL PL UNGE BASE T Using T emplate Guides The plunge subbase will accept template guides. On the fixed base an accessor y subbase will be needed to accept template guides. Recommended accessories for use with your tool are available at extra cost fr[...]

10 Using a P arallel F ence (Fig. 8A) A basic parallel fence is included with the D26204- XE and works with the fixed base. The basic parallel fence D262003- XJ is available as an accessor y for the other models and may be purchased from your local retailer or ser vice center at extra cost. 1. Remove the motor unit from the base unit. Refer to Moto[...]

11 FIG. 9 V W FIG. 10 HH II KK JJ U X 4. When using vacuum attachment, be aware of the placement of the vacuum cleaner . Be sure that the vacuum cleaner is stable and that its hose will not inter fere with the work. Vacuum Attachment (Plunge Base Only , Fig. 10) 1. Remove the motor unit from the plunge base. Refer to Motor Quick Release . 2. Slide [...]

12 Set-up: Plunge Base INSERTING THE MOTOR INTO THE PL UNGE BASE (FIG. 1, 11) WARNING: T o reduce the risk of injury , turn unit off and disconnect it from power source before installing and removing accessories, before adjusting or when making repairs. An accidental star t-up can cause injur y . 1. Remove the depth adjustment ring FIG. 11 B (B) fr[...]

13 FINE ADJUSTMENT OF ROUTING DEPTH (FIG. 12) WARNING: T o reduce the risk of injury , turn unit off and disconnect it from power source before installing and removing accessories, before adjusting or when making repairs. An accidental star t-up can cause injur y . The knurled knob (CC) at the bottom end of the depth adjustment rod can be used to m[...]

14 VARIABLE SPEED CONTROL (FIG. 1) This router is equipped with a variable speed dial (C) with an infinite number of speeds between 16000 and 27000 RPM. Adjust the speed by turning the variable speed dial (C). NOTICE: In low and medium speed operation, the speed control prevents the motor speed from decreasing. If you expect to hear a speed change [...]

15 ACCESSORIES WARNING: Since accessories, other than those offered by D E WAL T , have not been tested with this product, use of such accessories with this tool could be hazardous. T o reduce the risk of injur y , only D E WAL T recommended accessories should be used with this product. Recommended accessories for use with your tool are available a[...]

[...]

[...]

Stanley Black & Decker 82 T ar yn Drive, Epping, VIC 3076 Australia • 1800 444 224 (Aust) or 0800 339 258 (NZ) www .dewalt.com.au • www .dewalt.co.nz (MAR12) Par t No. N138667 D26204- XE Copyright © 2012 D E WAL T The following are trademarks for one or more D E WAL T power tools: the yellow and black color scheme; the “D” shaped air i[...]