DeWalt DCD775KLR инструкция обслуживания

DC720- XE, DC730- XE, DC743- XE CORDLESS COMP ACT 1/2" (13 mm) DRILL/DRIVER DC725- XE, DCD775- XE, DC727- XE, DC737- XE CORDLESS COMP ACT 1/2" (13 mm) DRILL/DRIVER/HAMMERDRILL INSTRUCTION MANU AL[...]

[...]

1 IF YOU HA VE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY D E WAL T TOOL, CALL US A T : 1800 654 155 (Aust) or 0800 339258 (NZ). SAFETY INSTRUCTIONS FOR POWER TOOLS When using power tools, always obser ve the safety regulations applicable in your countr y to reduce the risk of fire, electric shock and personal injur y . Read the following safety i[...]

2 c) Prevent unintentional starting. Ensure the switch is in the off position before connecting to power source and/or battery pack, picking up or carrying the tool. Car r ying power tools with your finger on the switch or energising power tools that have the switch on invites accidents. d) Remove any adjusting key or wrench before turning the powe[...]

3 • Replacement of the supply cord. If the supply cord is damaged, it must be replaced by the manufacturer or an authorised D E WAL T Service Centre in order to avoid a hazard. Extension Cords CAUTION: Use only extension cords that are approved by the countr y’s Electrical Authority . Before using extension cords, inspect them for loose or expo[...]

4 DANGER: Electrocution hazard. Never attempt to open the battery pack for any reason. If batter y pack case is cracked or damaged, do not inser t into charge r . Do not cr ush, drop or damage batter y pack. Do not use a batter y pack or charger that has received a sharp blow , been dropped, r un over or damaged in any way (i.e., pierced with a nai[...]

5 SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM ION (LI-ION) • Do not incinerate the battery pack even if it is severely damaged or is completely worn out. The batter y pack can explode in a fire. T oxic fumes and materials are created when lithium ion batter y packs are burned. • If battery contents come into contact with the skin, immediately wash[...]

6 • An extension cord must have adequate wire size (AWG or American Wire Gauge) for safety . The smaller the gauge number of the wire, the greater the capacity of the cable, that is 16 gauge has more capacity than 18 gauge. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. When using more than one ex[...]

7 Charge Indicators Some chargers are designed to detect cer tain problems that can arise with batter y packs. Problems are indicated by the red light flashing at a fast rate. If this occurs, re-inser t batter y pack into the charger . If the problem persists, try a different batter y pack to determine if the charger is OK. If the new pack charges [...]

8 OPERA TION WARNING: T o reduce the risk of serious personal injury , turn tool off and disconnect tool from power source before making any adjustments or removing/ installing attachments or accessories. FIG. 2 G FIG. 3 Installing and Removing the Battery Pack (Fig. 2, 3) NOTE: Make sure your batter y pack is fully charged. T o install the battery[...]

9 T o remove the battery pack from the tool , press the release buttons (G) and firmly pull the batter y pack out of the tool handle. Inser t it into the charger as described in the charger section of this manual. Variable Speed Switch (Fig. 1) T o turn the tool on, squeeze the trigger switch (A). T o turn the tool off, release the trigger switch. [...]

10 WARNING: T o reduce the risk of FIG. 4 DRILLING C personal injury , AL WA YS ensure workpiece is anchored or clamped firmly . If drilling thin material, use a wood “back-up” block to prevent damage to the material. 1. Use sharp drill bits only . For WOOD, use the low speed setting and twist drill bits, spade bits, power auger bits, or hole s[...]

11 Screwdriver Operation (Fig. 6) 1. Select the desired speed/torque range SCREWDRIVING FIG. 6 C using the dual range gear selector to match the speed and torque of the planned operation. 2. T urn the torque adjustment collar to the desired position. Lower numbers indicate lower torque settings; higher numbers indicate higher torque settings. 3. In[...]

12 • Damage caused where repairs have been made or attempted by others. • Damage due to misuse, neglect, wear and tear , alteration or modification. This warranty gives you specific legal rights and you may have other rights under the provisions of the Consumer Guarantee Act 1993 (New Zealand only), T rade Practices Act 1974 and State Legislati[...]

13[...]

Battery Output Chargers/Charge Time Nominal 240 Volts 12 Volts X Indicates that the battery pack is not compatible with that specific charger. All charge times are approximate. Actual charge time may vary. Read the instruction manual for more specific information. The battery voltage is nominal, it can measure above or below depending on the state [...]