DeWalt DCD785C2R инструкция обслуживания

www . .eu DCD730 DCD735 DCD780 DCD785[...]

1 Figure 1 a b c d f e g h i k j h Figure 2 k j l[...]

2 Figure 3 Figure 7 c c f Figure 4 Figure 5 Figure 6 Figure 8 Figure 9 m n[...]

ENGLISH 33 CORDLESS COMP ACT 13 mm (1/2") DRILL/DRIVER DCD730, DCD780 CORDLESS COMP ACT 13 mm (1/2") DRILL/DRIVER/ HAMMERDRILL DCD735, DCD785 Congratulations! Y ou have chosen a D E WAL T tool. Y ears of experience, thorough pr oduct development and innovation make D E W AL T one of the most reliable partners for professional power tool u[...]

ENGLISH 34 Vibration emission value a h Screwdriving a h,ID = m/s² < 2.5 2.5 < 2.5 2.5 Uncertainty K = m/s² 1.5 1.5 1.5 1.5 The vibration emission level given in this information sheet has been measured in accor dance with a standardised test given in EN 60745 and may be used to compare one tool with another . It may be used for a prelimina[...]

ENGLISH 35 EC-Declaration of Conformity MACHINERY DIRECTIVE DCD730, DCD735, DCD780, DCD785 D E W AL T declares that these products described under T echnical Data are in compliance with: 2006/42/EC, EN 60745-1, EN 60745-2-1, EN 60745-2-2. These products also comply with Dir ective 2004/108/EC and 2011/65/EU. For more information, please contact D E[...]

ENGLISH 36 d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury . e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. f) Dress properly . Do not [...]

ENGLISH 37 • W ear safety goggles or other eye protection. Hammering and drilling operations cause chips to fly . Flying particles can cause permanent eye damage. • Accessories and tool may get hot during operation. Wear gloves when handling them if performing heat producing applications such as hammerdrilling and drilling metals. • Do not op[...]

ENGLISH 38 • Do not use an extension cord unless it is absolutely necessary . Use of improper extension cord could result in risk of fire, electric shock or electrocution. • When operating a charger outdoors, always provide a dry location and use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk[...]

ENGLISH 39 Important Safety Instructions for All Battery Packs When ordering r eplacement battery packs, be sure to include the catalog number and voltage. The battery pack is not fully charged out of the carton. Before using the battery pack and charger , read the safety instructions below and then follow the charging procedur es outlined. READ AL[...]

ENGLISH 40 Read instruction manual before use. Charging. Fully charged. Hot/cold pack delay . x Problem pack or charger . Problem powerline. Do not probe with conductive objects. Do not charge damaged battery packs. Use only with D E W AL T battery packs. Others may burst, causing personal injury and damage. Do not expose to water . Have defective [...]

ENGLISH 41 Electrical Safety The electric motor has been designed for one voltage only . Always check that the battery pack voltage corresponds to the voltage on the rating plate. Also make sure that the voltage of your charger corresponds to that of your mains. Y our D E WAL T charger is double insulated in accordance with EN 60335; ther efore no [...]

ENGLISH 42 NOTE: The first time the tool is run after changing the direction of r otation, you may hear a click on start up. This is normal and does not indicate a problem. T orque Adjustment Collar (fi g. 1) Y our tool has an adjustable torque screwdriver mechanism for driving and removing a wide array of fastener shapes and sizes and in some mod[...]

ENGLISH 43 T o move belt hook or bit clip, remove the scr ew (h) that holds it in place then reassemble on the opposite side. Be sure to secur ely tighten the screw . OPERA TION Instructions for Use WARNING: Always observe the safety instructions and applicable regulations. WARNING: T o reduce the risk of serious personal injury , turn tool off and[...]

ENGLISH 44 NOTE: A smooth, even flow of dust from the hole indicates proper drilling rate. Screwdriver Operation (fi g. 6) 1. Select the desired speed/torque range using the dual range gear selector to match the speed and torque of the planned operation. 2. T ur n the torque adjustment collar (c) to the desired position. Lower numbers indicate low[...]

ENGLISH 45 advantage of this service please return your product to any authorised repair agent who will collect them on our behalf. Y ou can check the location of your nearest authorised repair agent by contacting your local D E W AL T office at the address indicated in this manual. Alternatively , a list of authorised D E WA L T repair agents and [...]