Diamond D400.1 инструкция обслуживания

D400.1 | D600.1 | D1000.1 AMPLIFIER INST ALL A TION MANUAL D300.2 | D300.4 | D600.4[...]

2 Congratulations! Thank you for choosing a new Diamond Audio amplier . Diamond Audio ampliers are engineered and produced with the highest quality materi- als and incorporate the latest technology . We think you will nd your new Diamond Audio amplier meets or exceeds your expectations and provides excellent value. Properly installed, y[...]

3 Fr equency Response: 20Hz to 20KHz +/-1 dB Signal to Noise Ratio: > 90dBA (20 to 20kHz) Channel Separation 60dB THD+N(T otal Harmonic Distortion + Noise) < 0.02%(Output-1W 4 Ohms) RCA Input Sensitivity: 150mV to 5V Min to Max V oltage requir ements 9V to 15.5V DC High/Low Pass Cr ossover: 12dB/Oct Variabl e Fr om 50-250Hz Cros sover Cong[...]

4 Connections and Contr ols This section describes all of the terminals and adjustments. 4 gauge power and ground wir e is recommended for all models. 2 and 4 Channel Models[...]

5 4 gauge power and ground wir e is recommended for all models. Connections and Contr ols This section describes all of the terminals and adjustments. Mono Models[...]

6 RCA Input and Pass-Thru Output - These RCA jacks allow for a normal Left and Right channel signal input. Simply connect to the source unit using RCA type audio cables, keeping them away from power wiring wher ever possible. On the 4 channel amplifiers “Fr ont” and “Rear” input jacks are present. The“Pass-Thru” output allows the signa[...]

7 Strapping Amplifiers (D600.1, D1000.1) MASTER SLA VE Wiring 1) Select one amplier t o be the mas ter amplier and one amplier to be the slave amplier . (All EQ and gain contr ols on the slave amp ar e disabled) 2) Set the phase adjustmen t switch on the Master amplier to 0° and the phase adjustment switch on the Slave amplier t[...]

8[...]

9 Installation Guidelines T ools and Supplies Listed bel ow ar e the tools and supplies needed to compl ete this installation: • V olt/Ohm Meter • Wir e strippers and wir e cutters • #2 Phillips scr ewdriver • Battery post wr ench • Hand held drill w/assorted bits • High quality electric al tape or heatshrink tubing • Soldering ir on [...]

10 Mounting Locations Engine Compartment Never mount this unit in the engine c ompartment. Mounting the unit in the engine compartment will void your warranty . T runk Mounting Mounting the amplier v ertically will pr ovide adequate cooling of the amplier . If you will be mounting it t o an existing panel, be sur e it’ s not prone to e xces[...]

11 3) T rim the power cable within 18 inches (45.7mm) of the positiv e battery pos t and splice in a in-line fuse holder . DO NOT inst all the fuse at this time. 4) Strip 1/2 inch (12.7mm) from the battery end of the power cabl e and crimp a lar ge ring terminal t o the cabl e. Connect the ring terminal to the positive (+) battery pos t. 5) Pr epar[...]

12 8) Connect from sour ce signal by connecting the RCA audio cabl es to the input jacks at the ampli- er . 9) Connect the car speak ers. Speakers should be 4 Ohms. If connecting one speaker per channel as shown in the diagrams (except where noted on D400.1, D600.1, D1000.1). Strip the speak er wir es 1/2” (12.7mm) and insert int o the speaker[...]

13 +12V GND REM 2 MIN POWER PROTECT SPEAKER FUSE 20 AX2 FL FR RL RR +12V GND REM 2 MIN POWER PROTECT SPEAKER FUSE 20 AX2 FL FR RL RR +12V GND REM 2 MIN POWER PROTECT SPEAKER FUSE 20 AX 2 FL FR RL RR D300.4, D600.4 4-Channel Amplifier 4 Channel Mode, 1 speaker per channel 3 Channel Mode, 1 pair stereo plus one bridged channel 2 Channel Mode, both p[...]

14 Installing the Remote Le vel Controll er The D400.1, D600.1, & D1000.1 come packaged with a remote le vel contr ol. This allows you to contr ol the level by attenuating the amplitude or increasing (up to the maximum set-point) of the amplier’ s input gain c ontrol. This contr ol does not add additional gain, it simpl y allo ws you to c [...]

15 Adjustment of Built-In Crosso ver (All Models) Placing the switch in the FULL position sets the amplier to F ull Range . This setting all ows ALL frequencies to pass to the speaker s. (Not availabl e on D600.1, & D1000.1). Placing the switch in the HP or LP position activates the cr ossover . Placing the switch in the HP position sets the[...]

041807 Diamond W arranty Diamond Audio warrants this product to be fr ee fr om def ects in material and w orkmanship for a period of one (1) year fr om the original date of pur chase pr ovided it was purchased from an authorized DA T r etailer within the United States. However, if this pr oduct is installed by an authorized DA T retail er, the warr[...]