DigiTech RV-7 инструкция обслуживания

[...]

DECLARA TION OF CONFORMITY Manufacturer’ s Name: DigiT ech Manufacturer’ s Addr ess: 8760 S. Sandy Parkwa y Sandy , Utah 84070, USA declares that the product: Product name: HardWire R V -7 Product option: All (requires Class II power adapter that conforms to the requirements of EN60065, EN60742, or equivalent.) conforms to the following Product[...]

WARRANTY : W e at DigiT ech are proud of our pr oducts and back-up each one with the following war ranty: The warranty registration car d must be mailed within ten da ys after purchase date to validate this warranty . DigiT ech warrants this product, when used solely within the U.S., to be free fr om defects in materials and workmanship under norma[...]

[...]

1 Introduction More than a remar kable achievement, HardWire ™ represents a collection of significant improv ements in effects pedals for guitar . HardWire pedals pro- vide a suite of well-known effects, each with superior tone and control. But these pedals go above and beyond their peer s, providing such distinguishing features as tr ue bypass, [...]

2 2 3 4 5 6 7 8 12 11 8 9 10 1[...]

3 W hat Does This Do? Le vel Knob - Controls the reverb level. T ur n this knob clock wise to inc rea se and co unte r -clo ckw ise to de crea se the reve rb lev el . DC Adapter Jack - Connect (an optional) Har man PS200R pow er supply to this jack. Use the proper supply for your area’s mains line voltage . Liveliness Knob - Controls the amount o[...]

4 REVERSE - reverb in reverse; quietly crescendos to full volume. MODULA TED - lush modulating reverb ideal for chords. GA TED - unique reverb with abr upt decay; good for percussive playing. HALL - lar ge encompassing reverb with war m decay . SPRING - classic “surf ” reverb; great for Rockabilly too! Input 1 (Mono) - Connect your instr ument,[...]

5 effect then fed to Outputs 1 and 2 keeping tr ue stereo separ ation between channels. F oot Switch Release Pins - These two pins are spring loaded hinges that hold the Foot Switch in place. See page 10 for infor ma- tion on accessing and changing the batter y . See page 6 for more information about using and changing the T ails Switch settings. I[...]

6 T ails Switch The HardWire Stereo Reverb features a switch that allows the reverb signal to continue being heard after the effect is bypassed. When the T ails Switch is set ON, the HardWire Stereo Reverb does not utilize tr ue hardwire bypass. If y ou always want to use tr ue hardwire bypass, set the T ails Switch to OFF . When the T ails Switch [...]

7[...]

8 Amplifier Setup PS200R (optional) or[...]

9 Ef fects Setup Note: If the amp effects loop has a mix control, set the mix to 100% full wet. AMP RETURN AMP SEND PS200R (optional)[...]

10 Batter y Operation In the event that batter y power is completely depleted, HardWire pedals automatically switch into bypass. This eliminates the need to remov e the pedal from your pedal chain if the batter y is dead. T o replace the batter y , do the follo wing: Using the tip of a 1/4” guitar cable , push one of the Release Pins in on either[...]

11 Switch is proper ly fastened, both release pins are flush with the outer side of the pedal. Foot Switch Pedal Switch Arm Foot Switch Release Pin 9VDC Battery Foot Switch Release Pin Pedal Chassis Battery Compartment Spring[...]

12 HardWire P erfor mance Accessories The performance accessor ies make integr ating a HardWire pedal into any pedal board a snap. The follo wing accessor ies are included: Hook-and-loop P edalboard Pad (designed to attach to the surfaces found on most commercial pedalboards) Foot Switch Glow Sticker (easily visible on dar k stages) StompLock™ (k[...]

13 Hook-and-loop Pedalboard P ad T o attach the P edalboard P ad, do the following: P eel off the existing r ubber skid pad from the bottom of the pedal. P eel the adhesive protector from the back of the P edalboard Pad. Apply the P edalboard Pad to the bottom of the pedal. 1. 2. 3.[...]

14 F oot Switch Glow Sticker T o attach the Foot Switch Glow Sticker , do the follo wing: P eel the adhesive backing from the Foot Switch Glow Sticker . Apply the Glow Sticker to the top of the Foot Switch. 1. 2.[...]

15 StompLock T o place the StompLock over the pedal knobs, do the follo wing: Set the knobs to your prefer red setting. Gently push the StompLock ov er the top of the knobs. T o remo ve the StompLock, gently lift one side and then the other . 1. 2. 3.[...]

16 Specifications Controls - Level, Liveliness, Decay , T ype, On/Off P edal Ja ck s - In pu t 1 (Mo no ), In pu t 2 , Out pu t 1 (M on o) , Out pu t 2 Input Impedance - >1 M Ω (stereo), >500 k Ω (mono) - effect on Output Impedance - 1 k Ω - effect on Input Impedance - tr ue hardwire bypass - effect off Output Impedance - tr ue hardwire by[...]

[...]

[...]

[...]

8760 South Sandy Parkwa y Sandy , Utah 84070 PH (801) 566-8800 F AX (801) 566-7005 HardWir e and DigiT ech are trademarks of the Harman Music Group Inc . Cop yright - Harman Music Gr oup Manufactured in the USA HardWir e R V -7 Owners Manual 18-0488-A Please visit us on the W orld Wide W eb at: www .digitech.com[...]