Dimension One Spas 01510-1030 инструкция обслуживания

[...]

[...]

Sonic Immersion System Table of Contents OWNER’S MANU AL ......................................................................... 1 F EATURES OF THE S ON IC I MMERSION ................................................. 1 U SING THE CD P LAYER ...................................................................... 1 DEALER INST ALLATION ...........[...]

Sonic Immersion System iii[...]

Sonic Immersion System Dea ler Owners Manua l Owner’s Manual Features of the Sonic Immersion • Dealer installation allows you to add to any Sonic Immersion System ready Dimension One Spa in stock • Patented planar magnetic speaker technolog y (1/4” thick) that generates unparalleled sound quality even in the harshest environmental conditio [...]

Sonic Immersion System Dea ler Installation Gu ide Dealer Installation This section intend ed for use by authorized dealer person nel only 2[...]

Sonic Immersion System Dea ler Installation Gu ide Getting Ready To Start The Sonic Immersion System can only be installed on spas with the following serial numbers . Table 1 Sonic Immersion System Ready Spas Model Serial Number Aurora HP 91275 or higher Aurora II 91210 and high er (Also 91184) Aurora XLT 91295 and higher Caliente HP 91301 and high[...]

Sonic Immersion System Dea ler Installation Gu ide Required Tools You will need the follo wing tools to complete the i nstallation: Table 2 Required Tools Electric drill 1 ½ inch hole saw ¼ inch drill bit 3/8 inch drill bit Saber Saw Phillips screwdriver Tape (masking, electrica l, duct, or packaging) ½ in width Spring-loaded punch (or other too[...]

Sonic Immersion System Dea ler Installation Gu ide Non Ratcheting PVC Pipe Cutter Medium Size Needle Nose Pliers Wire Stripper Utility Knife 5/16” Nut Driver or wrench Six inch square Stapler and Staples Straight E dge Safety Glasses Silicone caulking (clear) Small Saw 5[...]

Sonic Immersion System Dea ler Installation Gu ide Parts List You should have received th e following parts in the Soni c Immersion System installatio n kit: Table 3 Parts List Description Qty Item Number This document 1 01510- 1030 Amplifier 1 01564-08 Coarse- Threaded Drywall Screws 5 01051-0 6 Template 1 Doc 74- Rev A Power Supply Harness 1 0156[...]

Sonic Immersion System Dea ler Installation Gu ide Speakers, Satellite 2 01564-1 4 Stereo 1 01564-03 Sub-woofer sub assembly 1 01564-0 9 Stereo cover, marine 1 01564-0 4 Dual pole antenna 1 01564-0 5 Preamp stereo, cable 2 01570-2 4 Power supply screw, sheet metal, SS, PH 2 01011-3 8 7[...]

Sonic Immersion System Dea ler Installation Gu ide Marine cover screws, #8 x ½” SS Truss Head 4 01011-4 0 Cable Ty, 4” black 10 01200-0 06 Cable Ty Mount 10 01200-005 Removing Panels In order to install the system up to three panels must be r emoved from the spa: the equipment compa r tment panel, the panel where the sub woofer is installed, a[...]

Sonic Immersion System Dea ler Installation Gu ide 3. Locate the spa’s Main Top Side Contro l. 4. The Lower Control is located in the equipment co mpartment behind the spa pane l below the Main To p Side Control. 5. Use the screwdriver to remove the equi pment compartment panel screws. 9[...]

Sonic Immersion System Dea ler Installation Gu ide The number of screws to be removed will depend on the model of s pa. Remove the Sub Woofer Compartment Panel The installatio n location of the su b woofer compartment will vary from one spa model to another. Use Table 3 to locate the compartment on your spa. First, stand in front of the spa facing [...]

Sonic Immersion System Dea ler Installation Gu ide Sub-Woofer Table 4 Model List Model and Number Location of Installation Aurora II and Chairman Chairman II and Aurora XLT Diplomat, Califo rnian Nautilus 11[...]

Sonic Immersion System Dea ler Installation Gu ide Caliente HP, Triad II, Aurora HP, and Triad 1. Use the screwdriver to remove the spa panel screws. The number of screws to be removed will depend on the model of s pa. 12[...]

Sonic Immersion System Dea ler Installation Gu ide Installing the Sub Woofer Compartment The installatio n of the sub woofer compartment consists of removing the panel, removing the pa per cover, exposing the plug , removing the plug, and installi ng the sub woofer compartment. 1. If you have a spa with wood si ding you may skip to Step 2. If your [...]

Sonic Immersion System Dea ler Installation Gu ide The photograph above may not look like your spa, refer to Table 3. 3. Once the plug is exposed, use a screwdriver to punc h holes in the foam large enough to i nsert your hands and pull the plug out of the spa. The plug may not come out in one piece. 14[...]

Sonic Immersion System Dea ler Installation Gu ide 4. Use a medium size pair of ne edle nose pliers to remove the large staples in the bottom ra il where the plug was removed. 5. Remove all remnants of the plastic bag inside th e compartment where the plug was removed. This will expo se the electrical condu it. The electrical conduit may not always[...]

Sonic Immersion System Dea ler Installation Gu ide 6. Using a non-ratcheti ng PVC pipe cutter, trim the elec trical conduit flush with t he foam wall. 16[...]

Sonic Immersion System Dea ler Installation Gu ide 7. Locate the sub woofer sub assembly (P/N 01564-09). Locate the spot on the compartme nt that matches the locatio n of the conduit in the s pa. Using a1½ inch hole saw, drill a hol e for the conduit. 8. Try to place the sub woofer compartme nt into the space where the plug was removed. It mus t f[...]

Sonic Immersion System Dea ler Installation Gu ide 9. A properly positioned s ub woofer compartment is show n in the following photogra ph. 18[...]

Sonic Immersion System Dea ler Installation Gu ide 10. Once you are satisfied that the compartment fits properly , secure the compartment to the fra me with 5 1“ coarse- threaded drywall screws (P/N 0105 1-06 provided in hardware package). Pre Wiring from Equipment Compartment to Sub Woofer Compartment 1. Feed the fish tape throug h the conduit f[...]

Sonic Immersion System Dea ler Installation Gu ide 2. Now locate the amplifier cables (two white and two red RCA connectors on both ends, P/N 01570-24). Locate the three- branched harness assembly (P/N 01564-20). One bra nch will be considerably longer than the other two. 3. Attach the preamp stere o cables (01570-2 4) and long branch of main harne[...]

Sonic Immersion System Dea ler Installation Gu ide 4. Apply a small amount of fis h tape lubricant to a cloth and then run th e cables through the rag to give them a li ght coating of lubricant. 5. Now pull them through the condu it from the equi pment compartment to the sub-woofer compartment. 6. Now that the harness and cables have been fished th[...]

Sonic Immersion System Dea ler Installation Gu ide longer than necessary. Make sure that when the wires are connected to the amplifier that the amplifier can be moved out to make adjustments . Using a wire stripper, strip approximately ½ inch of insu lator from the 3 conductor wires. 7. Connect the black wire to the terminal marked GND. Connect th[...]

Sonic Immersion System Dea ler Installation Gu ide 8. Locate the wire coming from the sub-woofe r. This wire is covered with clear insulator. The wir e has two conductors. One is copper-colored and the other is silver. Strip approxim ately ½ inch of insula tor from each wire and twist each to form a tight bundle. Conn ect the copper colored wire t[...]

Sonic Immersion System Dea ler Installation Gu ide 10. Set GAIN CH 1 and CH 2 to 0.5V pos ition. 11. Set MODE to the 3ch position. 12. Set BASS BOOST CH1 and CH 2 to th e MIN position. 13. Set HIGH PASS CH 1 and CH 2 to the 200 HZ positio ns. 14. Set CH 1 to HP position and CH 2 to LP position. Installation of Power Supply Pre-Wire Power Supply Loc[...]

Sonic Immersion System Dea ler Installation Gu ide 1. Connect the wires from Row 1 (120 V Supply) to th e power supply as follows: black wire to the termi nal marked ”AC-L”, the white wire to terminal m arked “AC-N”, and the green wire to the terminal marked “FG”. 25[...]

Sonic Immersion System Dea ler Installation Gu ide 2. Connect the wires coming from Row 2 (Ster eo +12 V Supply) as follows: (see picture below) yellow an d red wires to terminal marked “DC+” and the b lack wire to terminal marked “DC-“. 3. Connect the wires coming from Row 3 (Amplifier) as follows (see picture below): red wir e to unused t[...]

Sonic Immersion System Dea ler Installation Gu ide Installing Power Supply in Equipment Compartment 1. Turn the p ower supply so that you can see the Voltage Selector Switch, see picture below, and pla ce the switch in the correct position ( 115V for UL and CSA spas or 240V for CE spas) for your location. 2. Locate two #8 x ½” Pan head screws (P[...]

Sonic Immersion System Dea ler Installation Gu ide 3. Locate the connector on the harness assembly that matches the one that you just installe d on the power supply and connect them together. 28[...]

Sonic Immersion System Dea ler Installation Gu ide Wiring the Power Supply 1. Locate the end of the harnes s that has a green, black, and white wire (with connectors). Remove lower control box cover. Insert these wires throug h the hole in the botto m of the lower control box. 2. Using a 5/16” nut driver or wrenc h remove the 5/16” nut that sec[...]

Sonic Immersion System Dea ler Installation Gu ide 3. Now place the green ground wire that you just inserted into the lower control box over the sc rew, replace 5/16” nut, and secure with 5/16” nut driver or wrench. 4. Connect the white and black wire s to the pins as outlined in the following t able. Table 5 Pin Connectors Board Description Pi[...]

Sonic Immersion System Dea ler Installation Gu ide Determining Location of CD Weather Cover The installatio n location of the CD Player Weather Cover (P/N 01564-04) dep ends on the model of the spa. The follo wing steps will guide you through the proces s of determining the instal lation location. 1. Refer to picture below . Measure distances A and[...]

Sonic Immersion System Dea ler Installation Gu ide It is important that the ruler or square (see picture on previous page ) be kept level and at the top of the recess area while making these measurements. 2. Use the measurements determin ed in Step 1 and insert them into the following formula: Distance A = __ ____ Distan ce B = _______ A + 1” = V[...]

Sonic Immersion System Dea ler Installation Gu ide 2. Using measurement obtained for Horizontal Position (HP) , measure from side of panel, see belo w, and mark spot with a fine point mar ker. 3. The point where these t wo lines intersect is the upper right corner of the template (P/N Doc 74 Rev A). 4. Align the upper right cor ner of the template [...]

Sonic Immersion System Dea ler Installation Gu ide 7. Using a 3/8”bit, drill holes in t wo corners of the rectangle. Make certain that the h oles are within the lin es. Using a center punch to mark the dr illing centers will prevent the drill bit from wanderi ng. 8. Using a saber saw, cut out the rectangular piece from the panel. 9. Depending on [...]

Sonic Immersion System Dea ler Installation Gu ide Installation of CD Pl ayer Door and Bezel If the bezel is not removed fr om the door assembly (P/N 01564-04), remove it by pull ing from the b ottom of the b ezel and then p roceed as follows: 1. Place the door assembly in the cutout. Make certain the door will open and close freely. Door should op[...]

Sonic Immersion System Dea ler Installation Gu ide To prevent wood panels from spli tting, driil pilot holes before installing the door assembly. 3. Reattach th e bezel. 4. Locate the mounting sleeve su pplied with the CD player and refer to the CD Player Owner’ s manual for directions on how to install this sleeve. On ce the CD player mounting s[...]

Sonic Immersion System Dea ler Installation Gu ide 3. Reattach panel to spa. 4. Connect antenna, main harness and amplifier to CD player as described in CD player owner’s manual. Connect po wer supply cable (long branch of main harness) to power supply connector on CD player. Connect Channel 1 preamp stereo cables (RCA cable) to FRON T connectors[...]

Sonic Immersion System Dea ler Installation Gu ide 1. Take the hinge mounting brac ket connected to the speaker (P/N 01564-14 ) and place it on the panel w ith the top triangular portion of the hinge butting up against the lower edge of the overhanging spa lip. 2. Remove the protective caps from th e hinge screw holes and using a center punch mark [...]

Sonic Immersion System Dea ler Installation Gu ide 39[...]

Sonic Immersion System Dea ler Installation Gu ide Installing the Satellite Speaker Wires 1. Remove the panel w here you just finished in stalling the speakers. 2. Locate two speaker wire sets (P/N 01 564-21). The wires have clear insulator with a silver and copper wire and female connectors on one end. 3. Using a Cable Tyes and Cable Mounts (P/N 0[...]

Sonic Immersion System Dea ler Installation Gu ide 41[...]

Sonic Immersion System Dea ler Installation Gu ide 5. Continue installi ng the wire until you reach the panel where the sub-woofer compart ment has been installed. Now use the Cable Tyes and Cable Mounts to attach the wire to the wood until you reach the su b woofe r compartment. 6. Trim any excess wire leaving enough to con nect the amplifier and [...]

Sonic Immersion System Dea ler Installation Gu ide 8. Now connect the wires coming from the sub-woofer compartment to the sate llite speakers. The wires from the speakers have male connectors and the wir es coming from the sub-woofer have female connectors. 9. Place the panel back on the spa and secure wit h screws. The finished installatio n shoul[...]

Sonic Immersion System Dea ler Installation Gu ide Securing the Amplifier Now that the speakers have been installed and the amplifier has been adjusted it can be secured to the fra me with dry wall screws supplied in the kit (P/N 01051-06). Complete the Installation Replace the spa panels to complete the ins tallation. 44[...]

[...]

Part No. 01510-1030 Rev A  2002 Dimension One Spas[...]