Dimplex LA16ASR инструкция обслуживания

CE MOUNTING and OPERA TING MANUAL Reversible Air-to-W ater Heat Pump for Outdoor Installation LA 16ASR Order No.: 452158.66.21 FD 8 5 07[...]

2 1 READ IMMEDIA TEL Y 3 1.1 Important Information 1. 2 Legal Provisions and Guidelines 1. 3 Energy-Efficient Use of Heat Pumps 2 PURPOSE OF HEA T PUMP 4 2. 1 Application 2. 2 Principle of Operation 3 SCOPE OF DELIVER Y 4/5 3. 1 Baseline Unit 3. 2 Control Box 3. 3 Heat Pump Controller 4 TRANSPORT 5 5 INST ALLA TION 6 5.1 General 5.2 Condensate Line[...]

3 READ IMMEDIA TEL Y 1.1 Important Information Prior to opening the unit it must be ensured that all electrical circuits are disconnected from the power source. During transport, the heat pump must not be tilted more than 45 ° (in either direction). Heat pump and transport pallet are only connected by the packaging film. The intake and outlet duct[...]

4 valve as well as the low-noise compressor , a desuperheater , a condenser and the electric control unit. In the case of low ambient temperatures, air humidity may accumulate on the evaporator in the form of frost impairing the heat transfer . The evaporator is automatically defrosted by the heat pump, if required. Cooling In the "cooling&quo[...]

5 2. 2. 1. 1. 1. 3. 1. 1. 3. 2. SCOPE OF DELIVER Y TRANSPORT 4 CAUTION! 3.2 Control Box The control box is integrated in the heat pump. It can be folded downward after removing the lower front panel and loosening the fastening screws located at the top on the right. The control box houses the mains terminals as well as the power contactors and the [...]

6 INST ALLA TION MOUNTING 6 INST ALLA TION 5.1 General The unit should always be installed on a permanently level, smooth and horizontal floor . The entire base frame surface should thereby make close contact with the floor in order to ensure adequate sound insulation and to prevent water-carrying parts from cooling out. If this is not the case, ad[...]

7 MOUNTING COMMISSIONING 6.3 Electrical Connection The power connection of the heat pump is effected via a commercially available 4-core cable. The cable has to be supplied by the client and the wire cross-section to be selected according to the power consumption of the heat pump (see Equip- ment Data in the appendix) as well as the relevant VDE (E[...]

8 COMMISSIONING CLEANING / MAINTENANCE f ) Once all heating circuit are fully open and a heating water temperature of approx. 25 ° C is maintained in the buffer tank, the minimum flow rate must be set on the overflow valve and the heating circulating pump. g) New buildings have an increased heat demand due to the energy required for structural dry[...]

9 CLEANING / MAINTENANCE MALFUNCTIONS / TROUBLESHOOTING DECOMMISSIONING the supply and return line of the heat pump. The regulations of the trade associations must be adhered to. If in doubt, contact the manufacturers of the chemicals! T o prevent consequential damage it is imperative that the water circuit be neutralized after cleaning using appro[...]

10 APPENDIX 11.1 DIMENSION DRAWING 1 1 11.2 EQ UIPMENT D A T A 1 2 11.3 SCHEMA TICS 1 1.3.1 Heating Mode 1 3 1 1.3.2 Cooling Mode 1 4 11.4 WIRING DIAGRAMS 1 1.4.1 C ontrol 15 1 1.4.2 Load 16 1 1.4.3 T erminal Diagram 1 7 1 1.4.4 Legend 18 11.5 HYDRA ULIC BL OCK DIAGRAM 1 9 11.6 EC DECLARA TION OF CONFORMITY 2 0 11.7 W ARRANTY CER TIFICA TE AFTER-SA[...]

11 Dimension Drawing APPENDIX: 11.1 DIMENSION DRAWING[...]

12 Equipment Data APPENDIX: 11.2 EQUIPMENT D A T A[...]

13 1 1.3.1 Heating Mode APPENDIX: 11.3 SCHEMA TICS[...]

14 1 1.3.2 Cooling Mode APPENDIX: 11.3 SCHEMA TICS[...]

15 1 1.4.1 Control APPENDIX: 11.4 WIRING DIAGRAMS Cable diameters all 0,75mm 2 Control lead 20x1,0mm 2 Heat pump controller[...]

16 1 1.4.2 Load APPENDIX: 11.4 WIRING DIAGRAMS PE distributor Mains Cable diameters all 0,75mm 2 ye/gn ye/gn[...]

17 1 1.4.3 T erminal Diagram APPENDIX: 11.4 WIRING DIAGRAMS T erminal connection diagram and connector assignment in the reversible air-to-water outdoor unit ye/gn Mains Control lead Connecting lead Load Wire () and pin numbers Control lead Wire () and pin numbers Heat pump controller Heat pump controller ye/gn[...]

18 E1 Crankcase heater , compressor E2 Fan for nozzle ring heater E3 Defrost end pressostat E4 Condensing pressure pressostat F2 High-pressure pressostat F3 Low-pressure pressostat F5 Thermostat HG F2 3 Winding shield, fan K1 Compressor contactor K2 Fan contactor M 1 Compressor M 2 Fan N 1 Heat pump controller N 3 Soft start control R9 Frost protec[...]

19 Hydraulic Block Diagram APPENDIX: 11.5 HYDRA ULIC BL OCK DIAGRAM N1-N05 (HUP) N1-N06 (WUP) N2-N02 (SUP) N1-N010 EV N1-B3 (WWF) KW T WW EV N2-N01 (HUPR) N1-B6 (NKF) N1-N04 (2.WE) N1-N012/N013 (MAN/MZN) M N1-N011 (HPN) X8/X11 N1-B1 (AUF) T T 1 5 6 2 4 3 Standardregler (mit Display) Kühlregler (ohne Display) Außenwandfühler Elektroverteilung Hei[...]

20 EC Declaration of Conformity APPENDIX: 11.6 EC DECLARA TION OF CONFORMITY Declaration of Conformity The undersigned KKW Kulmbacher Klimageräte-W erk GmbH, Geschäftsbereich Dimplex Am Goldenen Feld 18 D-95326 Kulmbach her eby confirm that the design and construction of the pr oduct(s) listed below , in the version(s) placed on the market by us,[...]

Notes 21[...]

Notes 22[...]

Notes 23[...]

KKW Kulmbacher Klimageräte-Werk GmbH T echnical data subject to change without notice Geschäftsbereich Dimplex Fax +49 (0) 92 21 709-589 Am Goldenen Feld 18 www .dimplex.de D-95326 Kulmbach[...]