DMP Electronics XR2400F инструкция обслуживания

Users Guide XR2 400F Fire Command Center : http://www. guardianalarms . net[...]

Copyright© 2000 Digital Monitoring Products, Inc. Information furnished by DMP is believed to be accurate and reliable. This information is subject to change without notice. Silencing an Alarm While the fire alarm horns, strobes, or sirens are sounding use one of the following methods to silence the alarm. 1. Turn the keyswitch to enable the four [...]

iii User's Guide for XR2400F Addressable Fire Alarm Control Panels T able of Contents Section Page Section Page Emergency Evacuation Plans ............................................ iv About Y our Addressab le Fire Alar m Control P anel ............. 1 Fire Command Center .............................................. 1 User Menu ...........[...]

iv Emergency Ev acuation Plans The National Fire Protection Association recommends that you establish an emergency evacuation plan to safeguard lives in the event of a fire or other emergency. Use the following steps as a guide. Draw a floorplan of your home or business On a clean sheet of paper, draw the walls, windows, doors, and stairs. Also dra[...]

1 About Y our Addressable Fire Alarm Contr ol Panel The Addressable Fire Alarm Control Panel has been designed with your safety and comfort in mind. It uses the latest in computer based technology to create the most advanced and user-friendly fire, security, and access control system available. The Addressable Fire Alarm Control Panel combines ease[...]

2 Introduction Data Entry keys These keys allow you to enter your user code and other information into the system. The ARROW key The ARROW key is used to go back through the displays while operating your system. You can press the ARROW key to back up through the list of functions in the User Menu or to make a correction by erasing the last characte[...]

3 User Options Menu Press and hold the ARROW and COMMAND keys for about two seconds. The display shows SET BRIGHTNESS . Use the left SELECT key to lower the display brightness. Use the right SELECT key to increase the display brightness. Press COMMAND. At SET TONE , use the left SELECT key to lower the keyboard tone. Use the right SELECT key to rai[...]

4 Introduction Special Fire Command Center Displays As you use your system, you will occasionally see a display that asks you to enter a code or that describes a condition on the system. Below are some examples of the displays you will see: ALARM A 24 hour zone, such as a fire zone, has been tripped. Your system may sound bells and/or sirens. TROUB[...]

5 Fire Command Center User Menu Many of the features of your system have been put into a User Menu that you can access from the Fire Command Center or the Remote Fire Command Center. The menu requires you to enter your user code and then only shows those functions to which you have access. Some features displayed on the User Menu are not necessary [...]

6 Alarm Silence User Code Level: 2 and above. Function: Silences the alarm bell or siren during an alarm. Alarm Silence allows you to turn off the alarm bell or siren connected to your system during an alarm. Using Alarm Silence does NOT stop an alarm report from being sent to the central station and does not reset any alarmed devices. Use the Sens[...]

7 Outputs On Off User Code Level : 5 and above. Function : Allows you to turn the system relay outputs on and off. This function is used to individually turn your system’s relay outputs on and off. Your system may use these outputs to control such devices as smoke detectors, heat detectors, and other notification appliances. Turning the Outputs O[...]

8 User Menu System Status User Code Level : All users. Function : Displays the current condition of internal system hardware. System Status displays the condition of the panel's AC power, battery power, and optional panel tamper. When System Status is selected, each monitor is displayed followed by OKAY or TRBL (Trouble) to indicate the curren[...]

9 User Menu M e n u O p t i o n s 123 456 789 Sensor Reset ✔✔✔✔✔ ✔✔ Zone Stat us Syst em Stat us ✔✔✔✔✔ ✔✔ Di spl ay Events ✔✔✔✔✔ ✔✔ Al arm Si lence Syst em Test ✔✔✔✔ ✔✔ Zo n e M o n i to r ✔✔✔✔ ✔✔ Out pu t s On /Of f ✔✔✔✔ ✔ Servi ce R equest Fire Dri ll Set Ti m e User Code[...]

10 User Menu SYS STA T (system status) NO ALM SLN C (ala rm s ile n ce) NO SYS TEST (system test) SNSR R ST (sen sor re set) NO USR CODE (u se r co de) NO TIME (day, date, and time) NO OUTPUTS (out puts on/ off) NO DIS EV NT (di spl ay ev ent s) NO ZN S TA TS (zone status ) NO TEMP CO DE (tempo rary co de) * NO SERV R EQ (service r equest) NO FIRE [...]

11 User Menu Ambush Codes Your system may be programmed to allow user number one (1) to be an Ambush code. This Ambush code functions identically to a standard code with the exception that it sends a silent alarm to the central station. This silent alarm alerts the operator to a duress situation at the premises and prompts the immediate notificatio[...]

12 Setting the Date and Time User Code Level : 8 and above. Function: Allows you to change the current date and time displayed on the Addressable Fire Alarm Control Panel and used by the system to log events in its Event Memory program. Setting the System’s Date and Time 1. Access the User Menu. 2. Press COMMAND until TIME? displays. Press any SE[...]

13 User Menu Displa y Events User Code Level: All Users. Function: Allows you to review up to 200 past system events. There are three applicable event types: Zone Activity - Zone alarms, troubles, and restorals. User Code Changes - Adding, deleting, and changing user codes. Supervisory - Problems with the system’s hardware components. The system?[...]

14 User Menu User Code Change Event Displays This displays any addition, deletion, or change to a user code. Display Description A DD 1 1: 41A 10 / 1 7 User 19 added by user 12 at 11:41 AM . U S:19 BY US: 12 Press the Select key under either user (US:) number for the user name. User Code Event Types - There are 3 event types you may see here: ADD -[...]

15 User Menu Fire Drill User Code Level: 8 and above. Your system may be programmed to allow a Fire Drill. The Fire Drill is used to test the fire bells, horns, and other notification appliances in your system. The Fire Drill turns on your system bell circuit, but does not send a message to the central station. Starting a Fire Drill 1. Access the U[...]

16 895 V oice Module You can also use the 895 Voice Module with the XR2400F Fire Alarm Control Panel. The 895 allows you to call your system using a touch- tone telephone, and perform a variety of functions, ranging from arming and disarming to turning outputs on and off. The 895 operates much like a voice mail system, providing you with easy to fo[...]

LT-0560 (12/00)[...]