Eagle Eagle View инструкция обслуживания

INST ALLA TION AND OPERA TION INSTRUCTIONS Eagle V iew TM ®[...]

Cop yr ight © 1996, 1997 Eagle Electronics All rights reser v ed. Eagle View ™ is a trademark of Eagle Electronics Eagle ® is a registered trademar k of Eagle Electronics W ARNING! USE THIS UNIT ONL Y AS AN AID T O NA VIGA TION. A CAREFUL NA VI- GA T OR NEVER RELIES ON ONL Y ONE METHOD T O OBT AIN POSI- TION INFORMA TION. Never use this pr oduc[...]

INTRODUCTION .......................................................................................................... 1 INST ALLA TION ............................................................................................................. 2 BRACKET INST ALLA TION ..............................................................................[...]

NA VIGA TION ................................................................................................................ 35 NA VIGA TE T O A W A YPOINT .................................................................................. 35 NA VIGA TE T O A CURSOR LOCA TION .................................................................. 35 NA [...]

1 Congratulations! Y ou ha v e purchased one of the finest 12-channel GPS receiv ers Eagle™ has e v er made. With its large LCD screen, easy to use menus, and out- standing perf ormance, we think y ou’ll be happ y with y our Eagle Vie w™ f or many years . GPS works from satellites that transmit inf ormation to the wor ld at v er y high freque[...]

2 y ou outstanding position and na vigation inf or mation. Most people are amaz ed when the y actually use a GPS receiv er and see what it does . Please sit do wn with the unit and this manual and f amiliar ize y ourself with them bef ore using the Eagle View in the “real wor ld”. A simulator is b uilt in, which lets y ou practice. INST ALLA TI[...]

3 Gimbal Bracket Washer Gimbal Knob Eagle View Attach the Eagle View to the gimbal bracket using the supplied gimbal knobs and washers as shown below.[...]

4 WHITE TO EA GLE VIEW 2-AMP FUSE GREEN BLA CK RED 12-V OL T B A TTER Y EA GLE VIEW TRANSMIT (NMEA) EA GLE VIEW RECEIVE (NMEA) PO WER The Eagle View will oper ate from a 12-v olt DC system. (9 to 15 volts DC .) Y ou can connect the po wer cab le to an accessory buss under the dash, ho we ver , to keep electrical noise interf erence to a minimum, w [...]

5 ANTENNA The Eagle Vie w’ s antenna can be mounted on any flat surface , pro vided you ha ve access behind the surf ace for the mounting scre ws. A magnet is also supplied that can be epo xied to the bottom of the antenna, allo wing it to be used on off-road v ehicles. A pole mount adapter lets y ou mount the antenna on a pole or s wiv el mount.[...]

6 After drilling the holes, pass the o-ring ov er the antenna cable and press it into the groo v e on the bottom of the antenna housing. Now attach the antenna to the mounting surf ace , using 4mm scre ws and the supplied loc k washers . Route the cab le to the Eagle Vie w and the antenna installa- tion is finished. Magnet Mount A magnet lets y ou [...]

7 KEYBO ARD The k e yboard has tw elv e k e ys. The arrow k e ys are tied to most of the f eatures, letting you easily mo v e the plotter’ s cursor , navigate through the menus , mak e selections from menus , and other tasks. The WPT k ey lets y ou create, sa v e, and recall wa ypoints and routes . The MODE k ey s witches the unit between the thr[...]

8 OPERA TION T urning P o wer On T o tur n the Eagle Vie w on, simply press the PWR ke y . A screen similar to the one at right appears. Read the message on the screen, then press the EXIT k e y to er ase it. The Eagle View is now ready f or use . MENUS Most of the Eagle View’ s adjustments and features are f ound on “menus”. Pressing the MEN[...]

9 Once the Eagle View loc ks on to the satellites and finds your position, it stores the satellite data in its memor y . The next time y ou use the unit, it should tak e much less time to loc k on. T o use your Eagle View , first make cer tain y ou ha ve a clear vie w of the sky , free from any obstructions such as trees, car por t, or a cov ered b[...]

10 arro w k e y . The screen sho wn at right ap- pears . Using the down arro w k e y , highlight the “Initialize GPS Receiv er” menu, then press the right arrow ke y . The screen sho wn below appears . This is the GPS initialization screen. The position, altitude , time , and date the Eagle Vie w is currently using to find the satellites is sho[...]

11 Now change the local time and date if the y’ re incorrect on this screen. (Don’t worry about altitude.) When ev erything is acceptab le , press the EXIT k e y repeat- edly to return to a mode screen. The Eagle View will instantly use the data you entered to find the satellites in the sky . (The unit kno ws which satellites will be a v ailab [...]

12 as "GRP" (groups). For e xample, Group A is the first windo ws group on the MODE menu.) Press the right arro w k e y to see more screens on each mode. When the desired screen appears, press the EXIT ke y to clear the menu. Note: F or a list of abbreviations used on the displa ys, see the bac k of this manual. Navigation Screens There a[...]

13 348°. The line e xtending behind the ar- ro w in the center shows y our tr ac k his- tor y , or path y ou’ve tr a v elled. Y our speed over g round or Ground Speed (GS) sho ws in the digital bo x to the right of the circle. The screen looks lik e this when you’ re not na vigating to a w aypoint. (See page 35 f or inf ormation on wa ypoint n[...]

14 Nav Screen #2 The na vigation screen sho ws navigation inf ormation in large digital numbers. T o vie w this screen, press the MODE k e y , then press the up arrow k ey until the b lack bo x surrounds the “NA V 1” label. Now press the right arro w ke y . A screen similar to the one at right appears. Press the EXIT k e y to er ase the mode me[...]

15 ro w ke y to move the b lac k bo x to the "PLO T" label. Now press the right arrow or left arro w k ey to select plot 2. This screen (as shown at the bottom of the pre vious page) has na vigation data display ed on the r ight side of the screen in digital n umbers. This data is active whene v er y ou’v e recalled a w a ypoint. Press [...]

16 Recor d T rail On / Off The line e xtending from the present po- sition diamond on the plotter is call the plot tr ail. As each dot on the trail is placed on the screen, it’ s also sa v ed in memor y . The plot trail recording can be tur ned off , if desired. T o tur n it off , press the up or do wn arrow k e y until the “Record T r ail” m[...]

17 In the tr ack-up vie w at right, the present position mo v es straight to w ards the top of the displa y . As y ou can see , the an- chor icon is no w shown in its proper ori- entation - to our right. A "N" shows to help y ou see which direction is nor th when the trac k-up mode is on. Remember , in the track-up mode , the screen rotat[...]

18 Grid Lines The Eagle View can place g rid lines on the plotter to help y ou see your position, or the position of w a ypoints and icons . T o do this, highlight the “Grid Lines” label on the “Plotter Opts” menu, then press the r ight arro w k e y to turn them on. Press the EXIT k e y to e xit this menu. A plotter screen similar to the on[...]

19 press the ENT k e y . The plotter screen re- appears with the icon at the cursor's lo- cation. Press the EXIT k e y to erase the cursor . On the screen shown at r ight, the large fish icon w as selected and placed at the cursor location. Erase Icons T o erase an icon from the screen, first press the MENU k e y , then select the “WPT/Icon [...]

20 the icon. If you wish to delete another icon, mo v e the cursor o v er it and press the ENT k e y . When you’ re finished, press the EXIT ke y to erase the cursor . WINDO WS This f eature giv es y ou 15 diff erent groups of windows so y ou can use the best na vigation displa y f or y our situation. T o use the windows f eature, press the MODE [...]

21 COURSE DEVIA TION INDICA T OR (CDI) The CDI sho ws your distance to the left or right of the desired course. Y ou must recall a w a ypoint or run a route to use the CDI. The arrow in the center of the bo x sho ws the direction to the destina- tion. For e xample, if you’ re tra velling straight to w ards the destination, the ar- ro w points str[...]

22 CLOCK Whene v er a clock, timer , or alarm is showing on a displa y , new items appear in the list when y ou press the MENU k ey . These items let y ou set the cloc k’ s time, alar ms, or the timers . Cloc k Set If the time sho wn on the cloc k displa y is not y our local time, change it using the “Cloc k Set” function. T o do this, press [...]

23 Timer s The Eagle Vie w has two timers built in. One is a countdo wn timer and the other is a count-up timer . The countdown timer counts do wn from the time y ou put in to zero . The count-up timer star ts at z ero and counts up to the time y ou entered. T o set either timer , first switch to a win- do w g roup with a timer . Ne xt, press the M[...]

24 This is the plot-2 edit screen. The “BRG” bo x in the upper r ight cor ner flashes , which means it’ s ready f or change . If y ou don’t w ant to change this bo x, simply press the up or down arro w ke y to mo v e to the bo x that y ou do w ant to change . In this e xample, w e will change the BRG bo x to g round speed, or GS . T o do th[...]

25 Sa ving The Cursor P osition as a W a ypoint When the cursor is sho wing on the plotter and y ou press the WPT ke y twice , the Eagle View puts the cursor’ s position into the first a v ailab le w a ypoint n umber . A message appears on the displa y telling y ou the wa y- point number it just used. W ait a fe w seconds and the menu will clear [...]

26 Highlight the “Sa ve P osition As” label as shown below left and press the right arrow k e y when y ou’ re at the location you wish to sa v e . This sa ves your present position under the w a ypoint number y ou selected on the first page. Sa ving Cursor P osition as a W a ypoint (Select Number Method) T o sav e the cursor position under a [...]

27 W A YPOINT NAMES It automatically assigns the wa ypoint number as a name when the w a ypoint position is sa v ed. Y ou can find a wa y - point by highlighting the “Name” label on the w a ypoint men u as shown at right. Now press the right or left arrow k e ys to scroll through the sa v ed w a ypoints. Only w a ypoints that ha v e a position [...]

28 sho wn at right. Press the down arrow k ey , then press the right arrow k e y until the desired w a ypoint n umber shows in the bo x. When e v er ything on this page is correct, press the ENT k e y . Note:The names in the “F rom” and “T o” bo x es are not the wa ypoint numbers - the y are the wa ypoint names. When a w a ypoint is mo v ed[...]

29 Delete a W a ypoint T o erase all of the inf or mation in a wa ypoint, simply press the WPT k ey , then select the w a ypoint y ou w ant to delete. Now highlight the “Wpt-Op- tions” label and press the r ight arrow k ey . Finally , highlight the “Delete WPT” label and press the r ight arrow k e y . A message appears, asking if y ou reall[...]

30 ROUTES Y ou can connect se v er al user wa ypoints together to f or m a route. When y ou recall the route, the Eagle View will sho w y ou na vigation inf ormation to the first wa ypoint in the route, then when you reach that wa ypoint, it s witches to the ne xt w a ypoint, and so on until y ou reach the last w a ypoint in the route. T o create a[...]

31 This menu lets y ou go to the w a ypoint selection menu, delete a w a ypoint from the route, or see details about an y wa y- point in the route . Since we want to add a w a ypoint to the route , press the right arrow k e y on the “Inser t F rom WPTS” label. The screen shown below appears . Select W aypoints Select the first wa ypoint either [...]

32 Finishing the Route When y ou’ve selected all of the wa ypoints f or the route, simply press the EXIT k e y until y ou return to the navigation, plotter , or windows screen. Y our route is sav ed in memory . Delete a W a ypoint T o delete a wa ypoint from a route , first select the route from the “Route Plan- ning” or “Run Route” menus[...]

33 The b lac k bo x is on the “Route # 1” label. If this isn’t the route y ou want to use , press the r ight or left arrow k e ys to s witch to another one . Bef ore star ting the route, y ou’ll need to decide if you w ant to star t at the begin- ning and tra v el forw ard or star t at the last wa ypoint in the route and tra vel bac kw ards[...]

34 Skip W a ypoint The Eagle Vie w lets you skip a w a ypoint in a route without stopping the route . T o do this, first press the MENU k ey , then highlight the “Routes” menu and press the right arrow k ey , then highlight the “Skip WPT” label and press the right ar- ro w k e y . The unit retur ns to the na viga- tion, plotter , or windows[...]

35 Navigating to a cur sor location The Eagle View lets y ou na vigation to a location without storing it in the wa ypoint database b y using the plotter and cur- sor . T o do this, first s witch to the plotter screen. Now mo v e the cursor to the lo- cation that you w ant to navigate to . Next, press the MENU k e y . A new men u ap- pears on the l[...]

36 Navigating to a W aypoint using the Plotter The unique “birds-e y e” view used b y the plotter giv es y ou an easy w a y to na vi- gate to a w a ypoint. On the screen show n at right, the diamond with a cross in it is y our present position. The bo x with the “S” in it was your star ting location when y ou recalled the w a ypoint. The do[...]

37 SYSTEM SETUP The Eagle View has se ver al menus and commands listed under the “System Setup” label on the main men u. These commands aff ect the basic oper ation of the unit. T o use them, press the MENU k e y , then highlight the “System Setup” label. Press the right arrow k ey . The screen shown at right appears . SPEAKER Y ou can tur [...]

38 T o change a unit of measure, first select the “Set Units” from the “System Setup” menu. The screen shown at r ight ap- pears . Highlight the desired selection, then press the left or right arrow ke y . Y ou can change one or all of the settings on this page . When y ou’ re finished, press the EXIT k e y . P osition Format T o change t[...]

39 NMEA / DGPS The Eagle View transmits data through the data por t in the bac k of the unit using NMEA 0183 f or mat, v ersion 1.5 or 2.0. This data is used by other electronic de vices such as mar ine autopilots for position and steer- ing inf ormation. DGPS on the other hand, is a data input. DGPS is an acronym f or Differ- ential Global P ositi[...]

40 All wiring connections to the Eagle View are made to it’ s pow er cab le. See the sample wiring diagrams on the ne xt page f or general wiring proce- dures . Read your other product’ s owner’ s manual f or more wir ing informa- tion. Once the cab les are wired, tur n the Eagle View on, press the menu k ey , and select NMEA / DGPS from the [...]

41 T O EA GLE VIEW O THER DEVICE 12 VDC BA TTER Y BLACK WIRE GROUND WIRES WHITE WIRE RED WIRE T O +12V O THER DEVICE’S RECEIVE D A T A WIRE EA GLE VIEW’S WIRES O THER DEVICE’S WIRES EA GLE VIEW TRANSMIT - TING NMEA D A T A TO ANO THER DEVICE T O EA GLE VIEW DGPS RECEIVER 12 VDC BA TTER Y BLACK WIRE GROUND WIRES WHITE WIRE RED WIRE T O +12V DG[...]

42 the e xception of serial communications, typically no other setup needs to be made with these receiv ers . If y ou ha v e any other Magna vo x or Starlink compatible DGPS receiv er con- nected to the Eagle View , you ma y need to change the settings . T o do this , mov e the b lack bo x to the “Configure DGPS Beacon Receiv er” label and pres[...]

43 If y ou restore the unit to the f actor y settings, all options such as contr ast, alarms, and other system choices are retur ned to their def ault values . Ho we v er , no wa ypoints , routes , or icons are erased. RESET GR OUPS T o return all groups to their f actor y defaults , highlight the “RESET GR OUPS” label on the “System Setup”[...]

44 the receiv er . For e xample, if you entered east longitude instead of west. Or if y ou’v e mov ed a long distance with the unit turned off. T o send a cold star t message to the re- ceiv er , highlight the “Ex ecute GPS Cold Star t” label, then press the right arrow k e y . A message appears, asking y ou if y ou really w ant to do a cold [...]

45 PCF (P osition Correction Factor) Another method used to mak e y our displa y match a char t or map is called “PCF” or P osition Correction F actor . This unit giv es y ou the capability to mo v e or offset the position sho wn on the displa y to match one on the char t . The unit will add this offset to all position and navigation displa ys [...]

46 After y ou’ve entered the latitude/longitude correction, press the ENT k ey to accept it. The Eagle View erases the PCF entry screen and retur ns to the na vigation or mapping screens with the correction f actor applied. POSITION PINING When using a GPS receiv er at e xtremely low speeds , it can hav e troub le determining your course o v er g[...]

47 T o use any of these alar ms, first press the MENU k ey , then select the “ALARMS/CDI” menu. A screen similar to the one shown at right appears . Press the up or down arro w ke y to move the b lack bo x to the desired alarm, then press the r ight arrow k e y to turn it on. T o adjust an alar m’ s distance, mo v e the blac k bo x to the ala[...]

48 SIMULA T OR A simulator is b uilt into the Eagle Vie w that has se v eral options. Y ou can use nearly all of the unit’ s f eatures - ev en sav e and recall wa ypoints. This is useful f or trip planning. T o use the simulator , press the MENU k e y , then press the up or do wn arro w k e ys until the “Sim ulator Setup” menu is surrounded b[...]

49 to increase or decrease the speed. Use the r ight and left arro w ke ys to change the trac k. Press the EXIT ke y to erase these men us . When y ou’ re finished changing the trac k and speed, press the EXIT k e y to erase the men us. T o tur n the simulator off, press the MENU k ey , then mo v e the blac k bo x to the “Simulator Setup” lab[...]

50 WINDO WS The f ollo wing is a listing of windows g roups A through O . GROUP “A” GROUP “B” GR OUP “C” GR OUP “D” GROUP “E” GROUP “F” GR OUP “G” GROUP “ H ”[...]

51 GROUP “I ” GROUP “J” GR OUP “K” GROUP “L ” GROUP “M” GROUP “N” GR OUP “O”[...]

52 Eagle's UPS Return Service - U .S.A. Only Eagle Electronics and United P arcel Ser vice (UPS) are proud to off er all of our customers free shipping f or all units sent to us f or repair or ser vice. If you ha v e to send this unit to the factor y , and you are in the continental United States, use the enclosed UPS shipping label f or easy [...]

53 KEEP THIS LABEL! Y OU WILL NEED IT IF Y OU EVER NEED T O RETURN Y OUR UNIT T O THE F A CT OR Y FOR REP AIR. Accessory Ordering Inf ormation T o order accessories such as pow er cab les , please contact: 1) Y our local marine dealer . Most quality dealers that handle mar ine elec- tronic equipment should be able to assist y ou with these items . [...]

54 EA GLE ELECTRONICS FULL ONE-YEAR W ARRANTY “W e", “our”, or “us” refers to EA GLE ELECTR ONICS , a division of LEI, the manuf acturer of this product. “Y ou” or “your” ref ers to the first person who purchases this product as a consumer item for personal, f amily , or household use. W e warrant this product against def ect[...]

55 ANTENNA MODULE TEMPLA TE 25MM (1”) (If Necessar y) 4.75MM (3/16”) 4 PLA CES[...]

56 THIS P A GE INTENTIONALL Y LEFT BLANK[...]

57 How to Obtain Service (Canadian Customers Onl y) W e back your in v estment in quality products with quic k, e xpert ser vice and gen uine Eagle replacement par ts. If you need ser vice or repairs, contact the Eagle F actor y Customer Ser vice Depar tment at the toll-free n umber listed below . A technician may be able to solv e the problem and [...]

58 Ho w to Obtain Ser vice - U .S.A. Only W e bac k y our inv estment in quality products with quick, e xper t ser vice and genuine Eagle™ replacement par ts . If y ou're in the United States and you ha v e questions , please contact the F actor y Customer Ser vice Depar tment using our toll-free n umber listed belo w . Y ou must send the un[...]