Emerson Process Management GFC инструкция обслуживания

www.EmersonProcess.com/Bristol Product Information Package PIP-Control Wave LS July, 2006 C ontrol Wave Loo p Power Su pp l y Control Wave LOOP POWER SUPPLY PRODUCT INSTALLATION GUIDE For the following Control Wave Series Products: MICRO, EFM, GFC, Ex p ressPAC & Ex p ress[...]

IMPORTANT! READ INSTRUCTIONS BEFORE STARTING! Be sure that these instructions are carefully read and understood before any operation is attempted. Improper use of this device in some applications may result in damage or injury. The user is urged to keep this book filed in a convenient location for future reference. These instructions may not cover [...]

WARRANTY A. Bristol warrants that goods described he rein and manufactured by Bristol are free from defects in material and workmanship for one year from the date of shipment unless otherwise agreed to by Bristol in writing. B. Bristol warrants that goods repaired by it pursuant to the warranty are free from defects in material and workmanship for [...]

How to return material for Repair or Exchange Before a product can be returned to Bristol for repair, upgrade, exchange, or to verify proper operation, form (GBU 13.01) must be completed in order to obtain a RA (Return Authorization) number and thus ensure an optima l lead time. Completing the form is very important since the information permits th[...]

Bristol Inc. Repair Authorization Form (off-line completion) (Providing this information will permit Bristol Inc. to effectiv ely and efficiently process you r return. Completion is required to receive optimal lead time. Lack of info rmation may result in increased lead tim es.) Date___________________ RA #___________________SH_ Line No.___________[...]

Bristol Training GET THE MOST FROM YOUR BRISTOL BABCOCK INSTRUMENT OR SYSTEM • Avoid Delays and problems in getting your system on-line • Minimize installation, start-up and maintenance costs. • Make the most effective use of our hardware and software. • Know your system. As you know, a well-trained staff is essential to your operation. Bri[...]

A Few Words About Bristol Inc. For over 100 years, Bristol ® has been providing innovative solutions for the measurement and control industry. Our product lines rang e from simple analog chart recorders, to sophisticated digital remote pr ocess controllers and flow computers, all the way to turnkey SCADA systems. Over the years, we have beco me a [...]

For technical questions regarding ACCOL products, OpenBSI Utilities , UOI and all other software except for Control Wave and OpenEnterprise products, call (860) 945-2286. For technical questions about Network 3000 hardware, call (860) 945-2502. You can e-mail the Application Support Group at: bsupport@bristolbabcock.com The Application Support Grou[...]

PIP-ControlWaveLS 1 Table Of Contents PIP-ControlWaveLS Control Wave Loop Supply Part Numbers 400095-01-7, 721708-01-3 & 721708-02-1 TABLE OF CONTENTS Section Title Page # Section 1 – LOOP SUPPLY INTRODUCTION 1.1 GENERAL DE SCRIPTI ON ..................................................................................................... 1 1.2 L[...]

PIP-ControlWaveLS Page - 1 Section 1 LOOP SUPPLY INTRODUCTION 1.1 GENERAL DESCRIPTION Bristol’s Control Wave Loop Power Supply (herein referred to as the “ Loop Supply ” ), provides regulated and isolated 24Vdc power outputs that can be used to power field devices such as transmitters or non-isolated I/ O circuits that are used in conjunction[...]

Page - 2 PIP-ControlWaveLS Figure 1 - Control Wave Loop Supply Board Views & Component Identification Diagram Table 1 - Input/Pass-through Power Connectors – TB1 & TB3 TB1 Pin # TB3 Pin # Signal Name Description Notes 1 3 VIN 9 to 30 +Vdc power Input or Non-fused Throughput 2 2 RET 9-30 Vdc Return Input or Non-fused Throughput 3 1 CHASSIS[...]

PIP-ControlWaveLS Page - 3 8-Pin Connector (TB2) accommodate s distribution of the regulated +24V loop supplies. Table 2 - Regulated 24V Supply Distribution Connector TB2 TB2 Pin # Signal Name Description 1, 3, 5, 7 +24V Regulated +24Vdc 2, 4, 6, 8 24V Return Reg. 24V Return • Configuration Jumper JP1 Jumper JP1 is used to set the input voltage r[...]

Page - 4 PIP-ControlWaveLS Section 2 LOOP SUPPLY INSTALLATION 2.1 LOOP SUPPLY MOUNTING Encapsulated Loop Supply Assemblies are prov ided with the printed circuit board (PCB) secured to a Power Supply Back Plate Bracket and protected by a Power Supply Board Cover. These units may be mounted directly to a panel or to a 35mm DIN Rail. Board only Loop [...]

PIP-ControlWaveLS Page - 5 Figure 3 - Encapsulated ControlWave Loop Supply Mounting Diagram[...]

Page - 6 PIP-ControlWaveLS 2.2 LOOP SUPPLY WIRING Loop Supply’s utilize Terminal Blocks that ar e equipped with compression-type terminals which accommodate a #16 AWG size wire. A conne ction is made by inserting the wire’s bared end (1/4” Max.) into the clamp beneath the screw and then tightening the screw. Three Loop Supply Terminal Blocks [...]

PIP-ControlWaveLS Page - 7 Figure 4 - ControlWave MICRO & EFM Loop Supply to I/O Module Wiring[...]

Page - 8 PIP-ControlWaveLS Figure 5 - Control Wave Express, ExpressPAC and GFC Loop Supply to Process I/O Board Wiring Diagrams Control Wave EFM – System Controller Module - Connector TB1 TB1-1 = +VIN (from loop Supply Connector TB3-3 = VIN) TB1-2 = -VIN (from loop Supply Connector TB3-2 = GND) Control Wave Express – CPU/System Controller Board[...]

PIP-ControlWaveLS Page - 9 Control Wave ExpressPAC – CPU/System Controller Board - Connector TB1 TB1-3 = POWER IN+ (from loop Supply Connector TB3-3) TB1-4 = GND (from loop Supply Connector TB3-2) Control Wave GFC – CPU/System Controller Board - Connector TB1 TB1-3 = POWER IN+ (from loop Supply Connector TB3-3) TB1-4 = GND (from loop Supply Con[...]

Page - 10 PIP-ControlWaveLS Section 3 SPECIFICATIONS 3.1 OPERATING SPECIFICATIONS Function: Provides four isolated 24Vdc power output terminal pairs to power an RTU , a Transmitter and/or a number of non-isolated I/O (associated with a particular Control Wave RTU. Output Voltage : Electrically Isolated & Regulated 24Vdc ± 5%, no load or full l[...]

PIP-ControlWaveLS Page - 11 Vibration: 1g for 10-500 Hz on any axis per SAMA PMC-31-1 without damage or impairment. .5g for 150-2000Hz RFI Susceptibility: 10V/meter – 80MHz to 1000MHz 3.3 CONNECTORS 3.3.1 Terminal Block TB1 3-Pin Terminal Block TB1 accommodates input power from the bulk DC source. TB1 could act as a power pass-through interface t[...]

Page - 12 PIP-ControlWaveLS Figure 6 - Loop Supply Dimensions Drawing[...]

Product Information Package PIP-Control Wave LS July, 2006 ControlWave Loop Power Supply The information in this document is subjec t to change without notice. Every effort has been made to supply complete and accurate information. However, Bristol, Inc. assumes no responsibility for any errors that may appear in this document. If you have comments[...]

Return to the T able of Content s Return to the List of Manuals[...]