Emerson KF180 инструкция обслуживания

Net Weight: 30.9 Lbs. Part No. F40BP72840003 Form No. BP7284-3 U.L. Model No.: KF180 READ AND SA VE THESE INSTRUCTIONS KF180AP01 Antique P ewter with Natural Cher r y/Mahogany Blades KF180OZ01 Olde Bronze ¨ with T eak/Natural Pine Blades KF180DBK01 Distressed Black with Distressed Black/Na tural Cher r y Blades STURBRIDGE Ceiling Fan Owner's [...]

W ARNING: T o avoid fire, shock, and serious personal injury , follow these instructions. Safety Instructions 1. Read your owner ’ s manual carefully and keep it for future reference. 2. Before servicing or cleaning unit, switch power off at service panel and lock service panel disconnecting means to prevent power from being switched on accidenta[...]

3 T ools Needed for Assembly One Phillips head screwdriver One wire stripper Six wire connectors (supplied) Three 60-watt (max.) candelabra base bulbs Materials Wiring, outlet box and box connectors must be of type required by the local code. The minimum wire would be a 3-conductor (2-wire with ground) of the following sizes: Installed Wire Length [...]

Preset Memory Feature Y our remote control receiver is equipped with a preset memory feature. The receiv- er will remember the light intensity and fan speed when the light and fan are turned off from the wall switch. When the wall switch is turned back on, the lights and fan will resume operation as they were prior to the switch being turned off. I[...]

2. Slide the four switch levers on the code switch to your choice of ON (up) or down positions. Use a ball-point pen or small screwdriver and slide the levers firmly up or down. 3. In the receiver (Figure 1), slide the four switch levers to the same positions as set in the transmitter . Make sure the levers on both switches are in the same position[...]

6 It is critical that the clevis pin in the motor coupling is properly installed and the setscrews securely tight- ened. Failure to verify that the pin and setscrews are properly installed (as shown in Figure 3) could result in the fan falling. ! W ARNING HAIRPIN CLIP DOWNROD CLEVIS PIN MOTOR COUPLIN G SETSCREW (2) Figure 3 3. T ighten the setscrew[...]

7 8. T urn the fan motor and housing assem- bly upside down in preparation for mounting the fan blade assemblies. Remove and discard the three shipping retainers securing the motor hub in the motor housing. NOTE: T ake care not to scratch the fan housing when installing the blade assemblies. 9. Insert a 1/4-20 x 1 1mm pan head screw with lockwasher[...]

2. Carefully lift the fan and seat the hang- er ball/downrod assembly on the hang- er bracket that was just attached to the outlet box (Figure 1 1). Be sure the groove in the ball is lined up with the tab on the hanger bracket (Figure 10). How to Hang Y our Ceiling Fan The fan must be hung with at least 7' of clearance from floor to blades (Fi[...]

9 1. Position the supply wires to the left side of the outlet box (Figure 12); position the fan wires to the right side. Partially insert the remote control receiver (flat side up) until one end rests on the hanger ball as shown in Figure 12. NOTE: Make all wiring connections using wire connectors (supplied). Make sure that all connections are tigh[...]

7. Screw three 60-watt (maximum) cande- labra base flame bulbs into the light fitter sockets (Figure 15). 8. Unscrew the six ring screws from the lower ring assembly (Figure 15). Position the lower glass in the lower ring assembly so that the six channels in the glass align with the six arms of the lower ring assembly . ARM LIGHT FITTER RING SCREWS[...]

button is held down. When the light is at the desired brightness, release the button. 5. T o turn the light on and off, press and release the button. The light will turn on at the light level previously set (see step 4). 6. If airflow is desired in the opposite direction, turn the fan off and wait for the blades to stop turning. Then slide the reve[...]

12 Do not use water when cleaning your ceiling fan. It could damage the motor or the blades and create the possibility of an electrical shock. ! W ARNING The use of any other control not specifically approved for this fan could result in fire, shock and per- sonal injury . ! W ARNING This product is designed to use only those parts supplied with th[...]

13 T rouble Shooting TROUBLE PROBABLE CAUSE SUGGESTED REMEDY 1. Fan will not 1. Fuse or circuit breaker 1. Check main and branch start. blown. circuit fuses or circuit breakers. 2. Loose power line 2. Check line power connections connections to the fan, or to fan and wire. loose wire connections in the switch housing. 3. W all switch is off. 3. T u[...]

14 Repair Parts 10 16 12 3 2 1 5 4 7 6 14 21 19 23 H I OFF LOW MED 24 11 15 13 9 17 20 25 8 22 18 BP7284, Sturbrige, KF180 7/31/06 10:52 AM Page 14[...]

Part Numbers Key Model No. Model No. Model No. N o . Description KF180AP01 KF180DBK01 KF180OZ01 * Hanger Pack, Consisting of: 761655-34 761655-36 761655-35 1 Hanger Bracket — — — 2 Hanger Ball — — — 3 Downrod — — — * Parts Bag, Containing: 762659 762659 762659 4 Wire Connector (7) — — — 5 Threaded Stud, 8-32 x 1-1/4” (2) ?[...]

LIMITED WARRANTY What The War ranty Covers: This warranty covers the motor and the other components and accessories of your Emerson ceiling fan against all defects in workmanship and materials. Y ou must be the original purchaser or user of the product to be covered. What The Period Of Coverage Is: As it applies to the motor , this warranty will la[...]