Epson 2100 инструкция обслуживания

ECO-FLO CONTINUOUS INK SYSTEM Perma Jet Assembly Instructions for : 2100 Ink System 1 Epson 2100 Eco-Flo Shown IMPORTANT If your printer is new, set it up acco rding to the enclosed manufacturers inst ru ctions. This is a check to ensure your new printer and drivers are working correctly before the Eco-Flo System is installed. EPSON PRINTER Epson 2[...]

2 ____________________________________________________________________________________________ Check Printer Condition Injector Set & Tubes Bottle Holder Tray Special Chip Block (Wrapped in Protective Packaging) 7 Empty 100ml Bottles Bottle Caps & Clear Piping 7 Tube Clamps Pair of Latex Gloves Tube Clip with A dhesive Pad Special Foam Bloc[...]

If you have a brand new printer, follow the Epson instructio ns for se tting up your printer. Use the Epson inje ctors that came with the printer. Follow normal installation in structions for the software. Test the printer by printing pictures. Learn how to use the Epson utilities to r un a No zzle pattern check and t o run a Cl eaning Cycle. Make [...]

Fig.2 Step 3 Bottle Preparation Locate the coloured bottle cap s and straight length s of plastic tubes. Insert the st raight tube firmly into the bottom of each bottle cap see Fig.3 Fig.3 Step 4 Tube Preparation 4[...]

Using a pair of scissors se parate all tub es by snipping gently at the tube ends. Please see Fig.4 to the left. Fig.4 5 Strip back all the tubes by approx 150mm. Please note when assemblin g the tubes to the bottle caps you may need to strip back more of the tubing in order for the bottles to be seated correctly within the bottle tray. Fig.5 Fig.6[...]

UB LC C LK Y LM M 2100 Setup Step 7 Assembling the Tubing to the Bottle Caps 6 When you have completed the above process insert the correct tube to the correct ink bottles. PLEASE TAKE CARE when doing this as if this is connected incorrectly there is no turning back see Fig.9 & Fig.10 Fig.9 Fig.10 Wing Adaptor Shown Step 8 Priming the Ink Throu[...]

This process is ca rri ed out by inserting the 10ml sy rin ge and 7 wing adaptor at the base of the injector. PLEASE ENSURE THAT THE WING ADAPTOR (TIP ONLY) IS GENTLY INSERTED INTO THE BASE OF TH E INJECTOR, DO NOT push the tip any further than 3mm (see diagram opposite) otherw ise this will split the base of the injector. PLEASE ENSURE that you DO[...]

Carefully align them, and when you are happy the injectors are in positio n. PLEASE BE CAREFUL NOT TO PUSH TOO HARD, AS THIS WILL CAUSE DA MAGE TO THE INJECTOR & PRINTE R HEA D . Push the injectors home until you feel a positive seat ed position see Fig.15 below. Fig. 15 Picture shows injectors fully installed in a 2100 Fig.14 Step 10 Positioni[...]

9 Next, you will notice that the Tube Support Bracket has both t he Hook and Loop Velcro o n it. The Hook portion of the Velcro is going to end up attached to your printer. The Loop portion will remain on the Tube Support Bracket. Do not separate the Hook a nd Loop. Fig.18 Fig.17 Use an alcohol or cleanin g solution and clean the top of t he printe[...]

This can be done manually by moving the head to the left and right and checking that there is just enough tubing to allo w the print head to move freely , without it dragging against any part of the printer see Fig. 20 & Fig. 21 below. 10 The tubing should look and be assembled as the diagrams opposite. Fig.20 Fig.21 PLEASE NOTE, due to the nat[...]

The printer should come on and the he a d should move back and forth a few times and do a cl eanin g cycle. When it stops moving, only the green light should be on. A red light at this point indicates that one of the chips has not been recogni zed. If this is the ca se please LOCK all tubes with the white clamps and very ca refully remov e the Inje[...]

1 ECO-FLO INSTALLATION INST RUCTIONS FOR ALL TYPES OF PRINTERS AND SYSTEMS 2 TROUBLE SHOOTING GUIDE 3 INK PURGE TEST FILES AND TONE CHARTS 4 ICC PROFILES FOR USE WITH PERMAJET COLOUR INK AND PAPER COMBINATIONS 5 CURVES FOR USE WITH MONOCHROMEPRO INK SYSTEM. IN ORDER TO USE THE PERMAJET INK SYSTEM TO ITS FULL POTENTIAL, YOU SHOULD NOW TAKE THE TIME [...]

• It is advised to gently shake by rotation each ink bo ttle on a regular weekly basis. This is to ensure the pigments stay suspended in solu tion and gives constant results. • After printing, ink in the tubes should be close to the injectors. The next morning, the ink may have retracted a little this is absolutely normal. When you start to pri[...]