Epson PRP-080 инструкция обслуживания

PRP-080 Series THERMAL RECEIPT PRINTER User's Manual Specifications subjects to change without notice[...]

-1- Contents 1. General Information 2. Quick Start 3. Printer Interface and Connection 4. Configuration 5. Safety and Maintenance 6. Appendix 1.1) Main Features...................................................................... 2 1.2) PRP-080I (Standard) & PRP-080II (Advanced) Function Comparison 2.1) Unpacking & Parts Identification 2.2[...]

1. General Information Models 1.1) Main Features Note: International font can be combined with others, for example PRP-080I-BI-MS, standard, Big5+International, beige, serial 160 (for PRP-080II)~220 (for PRP-080I) mm/s maximum print speed. Low-noise thermal printing. High reliability due to a stable mechanism. 1. High speed printing: 2. Application[...]

1. General Information Models 1.1) Main Features Note: International font can be combined with others, for example PRP-080I-BI-MS, standard, Big5+International, beige, serial 160 (for PRP-080II)~220 (for PRP-080I) mm/s maximum print speed. Low-noise thermal printing. High reliability due to a stable mechanism. 1. High speed printing: 2. Application[...]

2. Quick Start 2.1) Unpacking & Parts Identification a. Unpacking: B. Parts Identification: -5- -4- Printer cover Open this cover to load or replace paper . Control panel Features LED indicators to indicate printer status and buttons to operate the printer . Front cover Cover Open lever Pull this lever in the direction of the arrow to open the [...]

c. While observing the direction of the roll, set the paper roll into the hollow , and pull on the leading edge of the paper toward you as shown: d. Close the cover: When closing the cover , press the center of printer cover firmly to prevent paper miss-loading -7- -6- e. T ear off the paper outside the cover as shown.[...]

3. Printer Interface and Connection 3.1) Connecting the Interface Cable 3.2) Connecting to a Cash Drawer a. Before connecting/disconnecting the interface cable, make sure that power to the printer and all the devices connected to the printer is turned off. b. Connect the interface cable to the connector on the rear panel of the printer . c. In the [...]

(Blue LED) The POWER light is on whenever the printer is on. (Red LED) This indicates printer online/offline status or an error (Button) Press the FEED button to feed roll paper . (Button) Press the ONLINE button to set printer ONLINE/OFFLINE 4. Configuration Printer Control Panel & Status Indication 4.1) Panel LED indicators a. PRP-080I (Stand[...]

4.3) Printer Self T est 4.4) Driver Installation This is to test whether the printer is working properly or not and also checks the printing quality , firmware version, and DIP switch settings 1. Hold the ONLINE (*) button first and then turn on the power at the same time, release the button after around 1 second. 2. If the printer is working prope[...]

5. Safety and Maintenance 5.1) Safety Information 5.2) Periodical Cleaning 5.3) Preventing Paper Jams 1. Do not touch the HEAD of printer with anything. 2. Do not touch the cutter blade. 3. Only use the power supply that is come along with the printer . 4. Do not bend the power cord excessively or place any heavy objects onto it. 5. When connecting[...]

6. Appendix 1. Pr oduct Specifications 1.1) Printing Specifications 1.2) Auto Cutter 1.3) Paper Roll Supply Device 1. Printing method: Thermal line printing 2. Dot density: 203 dpi 203 dpi. 3. Printing direction: Unidirectional with friction feed 4. Printing width: 72 mm (2.83"), 576 dot positions 5. Characters per line (default): Font A: 48, [...]

1.7) Reliability 1.8) Environmental Conditions 1.9) Installation 1. Life Span: Mechanism: 15,000,000 lines Thermal head: 100 million pulses, 100 Km Auto cutter: 1,500,000 cuts (End of life span is defined to have reached the end of its life when it reaches the beginning of the W ear out Period.) 2. MTBF: 360,000 hours (Failure is defined as Random [...]

1.nterface connector terminal assignments and signal functions Pin number Signal name Signal Source Description 2 TXD Printer When using XON/XOFF handshake protocol, printer transmits control code XON/XOFF 3 RXD Host Printer receives data from host 4 R TS Printer Indicates printer current status, whether the printer is Busy or Ready to receive data[...]

-23- -22- 3. Drawer kick-out drive signal Output signal: Output voltage: Approximately 24 V Output current: 1A or less 2.2) Connectors a. Interface Connectors b. Power Supply Connector Pin Number Signal Name c. Drawer Kick-out Connector (Modular Connector) Drawer Kick-out Connector Pin Assignments Pin Number Signal Name Direction Refer to Interface[...]

General Printer Commands Command Lists: -25- -24- Command Code Description Function Description (Hex) HT 09 Horizontal tab LF 0A Print and line feed CR 0D Print and carriage return E S C$n L n H 1 B2 4n Ln H 0 nL 255 0 nH 255 E S C&yc 1c 2 1 B2 6yc 1c 2 y=3 32 c1 c2 126 E S C*mn L n Hd 1 d k 1 B2 Amn L n Hd 1 d k Select bit-image mode m=0,1,32,[...]

PRP-080I & II COMMANDS COMP ARISON Command Name PRP-080I PRP-080II (Standard) (Advanced) HT Horizontal tab * * LF Print and line feed * * FF Print and return to standard * mode in page mode CR Print and carriage return * * CAN Cancel print data in page mode * DLE EOT n Real-time status transmission * DLE ENQ n Real-time request to printer * DLE[...]

Note: Commands for International Fonts E S CRn Select an International Character Set Format ASC ESC R n Hex 1B 52 n Decimal 27 82 n Range 0 n 13 Description Selects an international character set n from the following table: N Character set 0 U.S.A. 1 Franch 2 Germany 3 U.K. 4 Denmark 5 Sweden 6 Italy 7 Spain 8 Japan 9 Norway 10 Denmark 1 1 Spain 12[...]

Character code can also be selected by utility pr ogram. 1. T o install the PRP-080 Default Code Page Setting utility , please insert the bundled CD disk into the CD-ROM drive. 2. In the CD-Rom menu, please go to Receipt Printer > PRP-080 > Code Page and double click the setup.exe file to begin the installation process and follow the installa[...]

Optional multilingual character model supports printing with one of the following characters: T o enable/disable the multilingual character code use the following commands: (*) a. B - T raditional Chinese (Big 5) b. G - Simplify Chinese (GB) c. K - Korean d. J- Japanese Kanji (JIS) FS & Select Multilingual Character Mode ON [Format] ASCII FS &a[...]