EverFocus EHD350/H-3 инструкция обслуживания

EVERFOCUS 1/3” 560 TVL High Resolution Color Rugged Dome Camera Operation Instructions Model No. EHD350 Please read this manual first for correct installa tion and operation. This m a nual should be retained for future reference. The information in this m anual was curren t when published. The manufacturer reserves the righ t to revise and improv[...]

1 the camera body . Use lens tissue or a cotton swab and ethanol to clea n the sensor and the camera lens. 7. Do not operate the camera beyond th e specified temperatur e, humidity or power sour ce ratings. Use the camera at temperatures with in –40 ℃ ~ 50 ℃ (-40F ~122F) and hum idity between 20%~ 80%. The input power source is 12VDC/24V AC. [...]

2 z Desiccant Pack x 1 z Manual x 1 Optional Accessory z W all Mount Bracket (BA-EHD) SPECIF ICA TIO NS Pickup Device 1/3'' SONY Super HAD CCD Video Format NTSC or PAL Scanning System NTSC: 525 TV lines, 60 fields/sec PAL: 625 TV lines, 50 fields/sec Picture Elements 768 x 494(NTSC) ; 752 x 582(PAL) Horizontal Resolution 560TVL Sensitivit[...]

3 24VAC: 20.5VA max. (heater ON ) 12VDC: 3.5W max. (heater OFF ) 12VDC: 11W max. (heater ON ) Dimensions 130mm(W) x 98.8mm(H) x 130mm ( D); 5.1"(W) x 3.9"(H) x 5.1"(D) Weight 1.7kg ; 3.7lbs Operating Temperature -40°C~50°C ; -40°F~122°F (20%~80% Humidity) Certifications FCC/CE DIMENSIONS INST ALLA TION 1. Loosen the 4 fix screws [...]

4 2. Remove the camera. T o remove the camera, first unp lug the wire connection on the back of the camera. Then loosen the 2 locking screws on the camera ba se, push the camera base to the right (toward heater direction, as shown in Figure 3), remove the cam era from the mounting base. Reinstall the camera and the cable wh ile the base mounting is[...]

5 Attach the base to the wall or ceiling , fix the base by the 4 setscrews attached in the accessory pack. The dome is weighted 1.7kg, please make sure if the mounting is strengthened enough to support it, if not, please reinfo rce the mounting according to the environm ent. Note : The diameter of the screw hole is ψ 4.7mm. Caution: T o prevent mo[...]

6 4. Re-assemble Camera 1. When mounting COLOR RUGGED DOME CAMERA on the wall, please aim the “ Wa l l ” in line with the triangle “ S ” m arked on the lead frame. (Factory default) 2. When mounting COLOR RUGGED DOME CAMERA on the ceiling, please aim the “ Ceiling ” in line with the triangle “ S ” m arked on the lead frame. 6 Figure[...]

7 5. W ire Connection Connect the power supply cable (AC 24V/DC12V), video output and alarm output to the proper connect ors shown as Figure 7. The V. Phase adjustment screw is located on the termination board. The vertical phase may require adjustment to synchronize the vertical phase of the camera with other cam era in the system wh en it is to b[...]

8 6. V i ew Angle Adjustment The camera can be rotated 360 ° horizontally , 140 ° vertically and 60 ° 3’rd axis view angles (as shown in Figure 8). Adjust the proper camera view angle as needed. If a vari-focal lens is used , you may adjust the focus and zoom of the lens to bring the object in focus. Be sure to loosen the lo cking screws on th[...]

9 DIP SWITCH FUNCTION LL (Line-Lock) OFF/ON To select the sync mode between Intern al Sync.(LL off) and Line-Lock (LL on). Set the line-lock off, the cam era will sync hronize to the internal tim e base. Set the line-lock ON, the camera’s vertical s ynchronization can be driven by the AC signal in the power lines. Note: Line-Lock sync mode operat[...]

10 BLC (Back Light Compensation) ON/OFF When BLC is turned on, the AGC, ES a nd IRIS operating points are determined by averaging over the center area instead of entire field-of-view, so that a dimly-lit foreground object at center area can be clearly distinguished from brightly-lit backgrounds. BLC should not be used unless it is n eeded to compen[...]

11 SIMPLE INSTRUCTIONS FOR THE DESICCANT P ACK Due to the camera lens blurred from the hum idity inside the camera. The desiccant pack absorbs the humidity; pleas e refer to the easy instruction as follows: 1. Adjust all settings first and pl ace the desiccant pack on the ho rizontal rod, then bend the horizontal rod and fix it. 2. Install the oute[...]

12 EverFocus Electr onics Corp. Head Office: 12F , No.79 Sec. 1 Shin-T ai W u Road, Hsi-Chih, T aipei, T aiwan TEL: +886-2-26982334 F AX: +886-2-26982380 www .everfocus.com.tw USA L.A. Office: 1801 Highland A ve. Unit A Duarte, CA 91010, U.S.A. TEL: +1-626-844-8888 F AX: +1-626-844-8838 www .everfocus.com USA N.Y . Office: 415 Oser A venue Unit S H[...]