Fisher-Price H7182 инструкция обслуживания

1 Instructions Model Number: H7182 Please read these instructions befor e assembly and use of this product. Adult assembly is requir ed. Tool needed for assembly: Phillips Scr ewdriver (not included). Requires thr ee “ AA ” (LR6) alkaline batteries for toy operation (not included). Product features and decor ations may vary from photo above. ww[...]

W ARNING This product contains small par ts in its unassemb led state. Adult assemb ly is required. Prevent serious injury or death fr om falls or sliding out: • The child should at all times wear a saf ety harness correctly fitted and adjusted. The tra y is not designed to hold the child in the chair . • Alw a ys keep child in vie w while in t[...]

Pa d Food Tr ay 2 Teether T oys Seat Back Frame Seat Bottom Frame Hinge Rod 2 Seat Bottom Tubes 2 Screw Retainer s Screw Retainer Screw Retainer Base Tr ay Footrest Front Base Back Base #10 x 2.2 cm Black Scr ew #10 x 2.2 cm Black Screw s - 2 #10 x 2.2 cm Black Scr ews - 2 #10 x 2.2 cm Black Scr ews - 2 #10 x 2.2 cm Black Scr ew - 7 Shown Actual Si[...]

4 3 • Slide a seat bottom tube thr ough each set of plastic rings on the seat bottom. 2 • Place the seat bottom face down on a flat surface. • At an angle, fit the footr est on the seat bottom, as shown. Assembly Plastic Rings Footrest Seat Bottom IMPORTANT! Before each use, inspect this pr oduct for damaged hardwar e, loose joints, missing p[...]

5 5 Assembly 5 Insert Scr ews Her e Footrest • Insert two #1 0 x 2.2 cm black screws thr ough the footrest and into the seat bottom. Tighten the screws. #1 0 x 2.2 cm Black Screw - 2 6 • T urn the seat bottom assembly upright. • Fit the seat back pins into the openings in the top side of the seat bottom assembly . Seat Back Pin Opening Seat B[...]

6 6 6 Assembly 9 Screw Retainer - 2 #1 0 x 2.2 cm Black Screw - 2 • P osition a fr ame so that the decorated side is outwar d. • Insert the back leg of a fr ame into the back base. • Fit a screw r etainer over the hole in the back base, as shown. • Insert a #1 0 x 2.2 cm black screw thr ough the screw r etainer and back base. Insert the bac[...]

7 7 7 Assembly 12 Front Leg Holes Screw Retainer - 2 #10 x 2.2 cm Black Scr ew - 2 • Insert the fr ame front legs onto the fr ont base. • Fit a scr ew retainer over a hole in the fr ont leg. • Insert a #1 0 x 7 / 8 " (2.2 cm) black screw thr ough the screw retainer and fr ont leg. Tighten the screw . • Repeat this pr ocedure to secur e[...]

8 8 8 Assembly Back and Bottom View Seat Bottom Tube Ends 14 Seat Height Adjuster s • Fr om the back and bottom of the assembly , insert a #8 x 1.9 cm screw thr ough both seat height adjusters and the ends of the seat bottom tube. Tighten the screws. #8 x 1.9 cm Screw - 2 15 Back and Bottom View Hole Pa d Hole Elastic Loops Elastic Loops Front Vi[...]

9 Assembly Shoulder P ortion 16 • Insert the cr otch belt through the slot in the pad. Make sur e the crotch belt is not twisted. • Fold the top of the pad down. • Remove the shoulder portion of the waist/shoulder belts by feeding them through the slots in the seat back. 17 • Lift the top of the pad. • Thr ead the waist/shoulder belts thr[...]

10 Battery Installation 1.5V x 3 "AA" (LR6) Battery Compartment Shown Actual Size • Loosen the scr ews in the battery compartment. Remove the battery compartment door . • Insert thr ee “ AA ” (LR6) alkaline batteries. • Replace the battery compartment door and tighten the screws. Hint: We recommend using alkaline batteries for l[...]

11 11 Securing Y our Child IMPORTANT! Before each use, inspect this pr oduct for damaged hardwar e, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing or br oken. Contact Mattel for replace- ment parts and instructions if needed. Never substitute parts. Place the high chair on a level, stable surface away from electri- [...]

12 12 Securing Y our Child 4 • To tighten the s houlder belts: Hold the adjuster and pull the front shoulder str ap down. • To loosen the s houlder belts: Slide the adjuster down. Note: After adjusting the restr aint system to fit your child, make sure you pull on it to be sur e it is securely fastened. Slide Adjuster Down Hold Adjuster Pull St[...]

13 Prevent serious injury or death fr om falls or sliding out. The child should at all times wear a saf ety harness correctly fitted and adjusted. The tra y is not designed to hold the child in the chair . W ARNING 7 • Fit the base tr ay onto the seat armrests. Push down until the base tray "snaps" into place. Hint: Before use, thorougl[...]

14 11 Release Bar Base Tr ay • While pushing the r elease bar on the front of the base tr ay , pull the tray base towar ds you and remove. • Insert the tab on the edge of the electr onic toy into the groove in the front of the base tr ay . • Push the electr onic toy down to secure in place. Hint: The electronic toy does not fit into the food [...]

15 Prevent serious injury or death fr om falls or sliding out. It is recommended that the high chair be used in the upright position only b y children capable of sitting upright unassisted. W ARNING Hint: Adjust the seat height to any of seven positions! 16 To adju st the seat height: • Pr ess the levers on both seat height adjuster s and lift or[...]

Storage Storage 19 Base Tr ay • Fit the holes on the base tr ay latches onto the pegs on the back of the high chair frame. • Fit the electr onic toy to the tab on the back of the high chair , as shown. Pe g Hole 20 Pull Frame Release Latch • With the legs all the way open, lower the seat to position 7 the lowest position). • Pull the fr ame[...]