Frigidaire L0806995 инструкция обслуживания

installation instructions For Heavy Duty (FAS Models) and Median (FAM Models) Air Conditioners Please read ALL instructions before installing. Two people are recommended to install this product. If a new electrical outlet is required, have the outlet installed by a qualified electrician before installing unit, See#5 in Preliminary Instructions following. Prelimi nary instru ctions Do the following before starting to install unit. See illustrations below. Check dimenstions of your unit to determine model type: Heavy duty (FAS) Median (FAM) Unit Height: 18,5/8" 17.5/8" Unit Width: 261/2" 231/2" Min. Window Opening: 19" 181/2" Min. Window Width: 31" 26 Vj&apos[...]

4. CHECK FOR ANYTHING THAT COULD BLOCK AIRFLOW - check area outside of window for things such as shrubs, trees, or awnings. Inside, be sure furniture, drapes, or blinds will not stop proper air flow. 5. Check the available electrical service - power supply must be the same as that shown on the unit serial nameplate. (See Owner's Guide for serial plate Iocation.)Power cord is 48"long. Be sure you have an outlet near. Tools Required a large flat blade screwdriver tape measure adjustable wrench or pliers pencil _/ Level _/ Socket wrenches _/ Phillips screwdriver All models have a 3-prong service plug to provide proper service and safe positive grouding. Do not change plug in any way. [...]

"ndow Mounting g Remove Chassis 1. Pull down front panel and remove filter. (See FIG. 1). 2. Lil_ front upwards and place to one side. D Install Top Angle and Side Bracket 1. Attach foam gasket to top angle above holes as shown in FIG. 6. 3. Locate the four front screws and remove. These screws will be needed to re-install the front later. (See FIG.2) 4. Pry away front from cabinet sides as per photo (see FIG .3) 5. Gently lift front off unit and place to one side (See FIG.4). 2. Install top angle and side retainers to cabinet as shown in FIG. 6. FIG. 6 6. Removeshi ppingcrewsfrom top d unit and_tso on theside by the base if installed. 7. Hold the cabinet while pulling on the base handl[...]

3. Insert top and bottom legs of window filler panel frame into channel in the to angle and bottom rail. Do both sides. 4. Insert washer head locking screws (2) into holes in top leg d filler panel frame (see Step 6). Do not totally tighten. Allow leg to slide freely. Screws will be tightened after Section 6. Place Cabinet in Window 1. Open window and mark center of window stool. M Install Support Bracket 1. Hold each support bracket flush against outside of sill, and tight to bottom of cabinet as shown below. Mark brackets at top level of sill, and remove. MARK . Place cabinet in window with bottom stool angle firmly scated over window stool as shown. Bring window down temporarily behind to[...]

Extend Window Filler ........... Panels 1. Carefully raise window to expose filler panel locking screws. Loosen screws so filler panels slide easily. install Chassis into Cabinet and install Front to Unit 1, Lift air conditioner and carefully slide into cabinet leaving 6" protruding, 2. _DO not push on controls OR finned coils. 3, Be sure chassis is firmly seated towards rear of cabinet. 4. Installation of front is the reverse of removal outlined in Section 1. 2. Extend panels to fill window opening completely. Tighten locking screws on top, 3. Close window behind top angle. Install Window Lock and Sash Seal 1, Trim sash seal to fit window width. Insert into space between upper and lowe[...]

Thru-The-Wall installation NOTE: Consult local building codes prior to installation, or a qualified carpenter. Select Wall Location This air conditioner has a slide-out chassis, so that it can be installed through an outside wall as specified below: Heavy Duty(FAS) Median (FAM) Max wall thickness 10" 8" IMPORTANT: Side louvers must never be blocked. NOTE: All parts needed for Thru-The-Wall Installation are provided,except a wood frame, shims, and 10 wood screws (#10-1" long minimum). Select a wall surface that: 1, does not support major structural loads such as the frame construction at ends of windows, and under truss-bearing points, etc. 2. does not have plumbing or wiring i[...]

NOTE: If wall thickness is 8-1/2" or more, add aluminum flashing over bottom of frame opening to assure no water can enter area between inner and outer wall. 1"LONG SCREW FIG. 2 ALUMINUM FLASHING OVER BOTTOM OF FRAME I Prepare and Install Cabinet Refer to Step 4 d Window Mounting for assembly of support brackets.A wooden strip nailed to the outside wall should be used in conjunction with sill support angle brackets. 1. Slide chassis from cabinet. Refer back to Step 1 of Window Mounting. 2. Place cabinet into opening with bottom rail resting firmly on bottom board d wooden frame. 3. Position cabinet to achieve proper slope for water removal. (See FIG.1 below.) FIG. 1 5/16" TO 3[...]

OPTIONAL: Caulking and installation of trim on interior wall may be done. You can buy wood from your local lumber or hardware supply. On the outside, caulk openings around top and sides of cabinet, and all sides of wood sleeve to the opening. NOTE: See Step 7, Item 3 of Window Mounting Instructions for bottom rail seal location. Masonry Construction 1. Cut or build a wall opening in the masonry wall similar to the frame construction(refer to Step 2 d Thru-the-Wall Installation for a wall thickness greater than 8-1/2"). 2. Secure cabinet in place using masonry nails, or the right masonry anchor screws.(Another way to do this is to build an in -between frame of2x4 's as shown in the [...]