Fujitsu ASU12CQ инструкция обслуживания

A S U 9 C Q A S U 1 2 C Q A O U 9 C Q A O U 1 2 C Q[...]

En-2 Fig. 1 Indoor Unit 1 Operating Control Panel (Fig. 2) 2 AIR CLEANER RESET / MANUAL AUTO button ● Intake grill opening mechanism. When the remote control is not available for use, this button can be used as a Quick-start button. However when the Air Cleaning check function (see page 13) is in operation, this button is used as a reset button. [...]

En-3 FEA TURES AND FUNCTIONS SLEEP TIMER When SLEEP is selected be pressing TIMER button during Heating mode, the air conditioner’ s thermostat setting is gradually lowered during the period of operation; during Cooling or Dry mode, the thermostat setting is gradually raised during the period of operation. When the set time is reached, the unit a[...]

En-4 PREP ARA TION CAUTION! ● T ake care to prevent infants from accidentally swallowing batteries. ● When not using the remote control unit for an extended period, remove the batteries to avoid possible leakage and damage to the unit. ● If leaking battery fluid comes in contact with your skin, eyes, or mouth, immedi- ately wash with copious [...]

En-5 T o Select Mode Operation 1 Press the ST ART / STOP button (Fig.6 M ). The indoor unit’ s OPERA TION indicator lamp (red) (Fig. 3 5 ) will light. The air conditioner will start operating. 2 Press the MASTER CONTROL button (Fig.6 H ) to se- lect the desired mode. Each time the button is pressed, the mode will change in the following order. AU[...]

En-6 OPERA TION About Mode Operation AUTO: ● Depending on the room temperature at the time operation begins, the operating mode will be switched automatically as shown in the accompanying table. Also, depending on the operating mode, the room temperature set- ting will cause the “standard” temperature to be set as shown. Actual Room Operating[...]

En-7 AIR CLEANING OPERA TION 2 Press the AIR CLEAN button (Fig. 6 N ). The AIR CLEAN indicator lamp (Fig. 3 7 ) will light up (green, as shown in the figure). ● Air conditioning and Air Cleaning will function simultaneously. Air cleaning ● During operation, the unit produces a small amount of ozone that can be smelled. ● When this unit is use[...]

En-8 TIMER OPERA TION T o Use the ON timer or OFF timer 1 Press the ST ART / STOP button (Fig. 6 M ). (if the unit is already operating, proceed to step 2). The indoor unit's OPERA TION Indicator Lamp (red) (Fig. 3 5 ) will light. 2 Press the TIMER button (Fig. 6 K ) to select the OFF timer or ON timer operation. Each time the button is presse[...]

En-9 SLEEP TIMER OPERA TION Unlike other timer functions; the SLEEP timer is used to set the length of time until air conditioner operation is stopped. T o Use the SLEEP T imer 1 While the air conditioner is operating or stopped, press the TIMER button (Fig. 6 K ). The indoor unit's OPERA TION Indicator Lamp (red) (Fig. 3 5 ) lights and the TI[...]

En-10 ADJUSTING THE DIRECTION OF AIR CIRCULA TION V ertical (up-down) direction of airflow is adjusted by pressing the Remote Control Unit’ s SET button. Horizontal (right-left) airflow direction is adjusted manually, by moving the Air Flow Direction Louvers. Whenever making horizontal airflow adjustments, start air conditioner operation and be s[...]

En-11 SWING OPERA TION Begin air conditioner operation before performing this procedure. T o select SWING Operation Press the SWING button (Fig. 6 P ). The SWING indicator lamp (orange) (Fig. 3 8 ) will light. In this mode, the Air Flow Direction Louvers will swing automatically to direct the air flow both up and down. T o Stop SWING Operation Pres[...]

En-12 Before cleaning the plasma filter unit, be sure to turn off the power supply to the air conditioner. Electric shock may result. ● When used for extended periods, the unit may accumulate dirt inside, reducing its performance. W e recommend that the unit be inspected regularly, in addition to your own cleaning and care. For more information, [...]

En-13 CLEANING THE PLASMA AIR CLEANING FIL TER CAUTION! W ARNING! ● Make sure the plasma filter unit is properly mounted before cleaning or performing other tasks on it. If the unit is not properly mounted, it could fall off and cause damage or injury. ● Y ou can be injured if you touch the heat exchanger when removing or installing the plasma [...]

En-14 5. Install the air filter. ● Please consult instructions for cleaning the air filter on page 12. 6. Close the intake grille. Push the intake grill in at 4 points (the two ends of its lower side as well as two center points of the lower side, as shown in the figure) to close it. ● If, after cleaning the dust collection unit, the operation [...]

En-15 Air -cleaning and Deodorizing filter maintenance As well as ensuring the maintenance of the dust collecting unit, please also take care of the filter. (Please carry out maintenance on the filter every 6 months.) 1. Open the intake grille and remove the air filter from the right side. ● Please consult step 1 of cleaning the air filter on pag[...]

En-16 TROUBLESHOOTING In the event of a malfunction (burning smell, etc.), immediately stop operation, disconnect the Power Supply Plug, and consult authorized service personnel. Merely turning off the unit’ s power switch will not completely disconnect the unit from the power source. Always be sure to disconnect the Power Supply Plug or turn off[...]

En-17 TROUBLESHOOTING Symptom Doesn’ t operate at all: Poor Cooling or Heating performance: The unit operates differently from the Remote Control Unit’ s setting: See Page — 8 - 9 — 5 4 CHECK ONCE MORE Items to check ● Is the Power Supply Plug disconnected its outlet? ● Has there been a power failure? ● Has a fuse blown out, or a circ[...]

En-18 OPERA TING TIPS Outdoor temperature Indoor temperature Cooling/Dry Mode About 32 to 115 °F About 64 to 90 °F T emperature and Humidity Range If the unit is used for long periods under high-humidity conditions, condensation may form on the surface of the indoor unit, and drip onto the floor or other objects underneath. About 80% or less Abou[...]