GE ZICS360 LH инструкция обслуживания

ZIC360N RH, ZIC360N LH, ZICS360N RH, ZICS360N LH Built-In Bottom-Freezer Refrigerators Design Guide With Installation Instructions Monogram. ® If you have questions , call 800.626.2000 or visit our website at: www .monogram.com Installation Instructions[...]

Safety Information Skill Level — Installation of this refrigerator requires basic mechanical, carpentry and plumbing skills. Proper installation is the responsibility of the installer . Product failure due to improper installation is not covered under the GE Appliance W arranty . See the Owner’ s Manual for warranty information. W ARNING: • T[...]

36" Frame to Frame Width *84" From Floor to Top Frame 35" Case Width *83-1/2" at Rear 25-3/4" Framed Models 25-3/4" Stainless Steel Models Case Depth Depth Including Handles: 26-7/8" Framed Models 27-3/4" Stainless Steel Models THE INST ALLA TION SP ACE Water And Electrical Locations Electrical and water supp[...]

1/4" 1/2" 3/4" 1" 1-1/4" 1" 3/4" Overlay Panel (Nominal Size) 1/4" 1/2" 3/4" 2" 1-1/4" 1-1/2" 1-3/4" 3" 2-1/4" 2-1/2" 2-3/4" 1/4" 1/2" 3/4" Door 23-7/8" From Rear of Refrigerator 1" Refrigerator Case Trim T op View 130° DOOR SWING (fa[...]

1/4" 1/2" 3/4" 1" 1-1/4" 1/4" 1/2" 3/4" 1" 1-1/4" 1-1/2" 23-7/8" From Rear of Refrigerator 3/4" Overlay Panel (Nominal Size) Case T rim Refrigerator Door 5 T op View 90° DOOR SWING (optional setting) Scale 1:1 Frameless Cabinets: The case trim overlaps cabinets at the top and sides. [...]

CUSTOMIZA TION BASICS: Framed Or Overlay Panels, Custom Handles and Accessory Kits Overlay panels Y ou may also choose to install custom overlay panels from your cabinet manufacturer . This design provides a seamless appearance which integrates smoothly with surrounding cabinetry . Standard supplied handles shown in 3/4" overlay panel position[...]

1/4" FRAMED P ANEL DIMENSIONS 7 If you choose to install framed panels, they must be cut to the dimensions shown. The panels will slide into the frame on the door , drawer and grille. If the custom panel is less than 1/4" thick and if it fits loosely in the door frame, it can be backed up with a piece of filler material or foam tape to im[...]

*84" 2-9/16" 24" *3" to 4" 3/16" 1-7/8" Design Guide 8 SIDE P ANELS Side panels must be used whenever the sides of the refrigerator will be exposed. The 1/4" side panels will slip into the side case trim. Secure the panels to the refrigerator with stick-on hook and loop fastener strips. Order the side panels [...]

Where a standard 2-prong wall outlet is encountered, it is your personal responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet. DO NOT , UNDER ANY CIRCUMST ANCES, CUT OR REMOVE THE THIRD (GROUND) PRONG FROM THE POWER CORD. DO NOT USE AN ADAPTER PLUG TO CONNECT THE REFRIGERA TOR TO A 2-PRONG OUTLET . DO NOT U[...]

STEP 1 REMOVE P ACKAGING CAUTION: Refrigerator is much heavier at the top than at the bottom – be careful when moving. When using a hand truck, handle from side only . PRUDENCE: Le réfrigérateur est beaucoup plus lourd en haut qu'en bas. Il faut être prudent lors des déplacements. Si un diable est utilisé, il faut soulever le réfrigér[...]

Block Soffit Side View Height From Floor to Bottom of Wood Block Brackets Required Brackets Not Required Beneath a Soffit 11 STEP 2A W A TER LINE INST ALLA TION WITH A REVERSE OSMOSIS SYSTEM Skip this step when not using an RO System If the water supply to the refrigerator is from a Reverse Osmosis W ater System use the refrigerator’ s filter byp[...]

12 STEP 5 LEVEL REFRIGERA TOR All models have 4-point leveling. The front is supported by leveling legs, the rear is supported by adjustable wheels. Both are accessible from the front of the refrigerator . • T o level the back of the refrigerator , turn the 7/16" hex nut located above the front wheels. T urn clockwise to raise or countercloc[...]

STEP 7 ADJUST DOOR SWING NOTE: This refrigerator has a 2-position door stop. When space does not allow the door to swing open fully to 130°, you may change the door swing to a 90° opening. Skip this step if door opening is satisfactor y for your installation situation. • Lift the grille panel to access the wire cover trim. • Remove screws on [...]

14 STEP 9 INST ALL FRAMED P ANELS • There are two sets of holes in the handle side trim. Replace handle side trim by installing the original screws in the FRONT screw holes. • Secure the handle to the door using the REAR screw holes. • Follow the same procedures to install the drawer panel. Use Rear Holes to Secure Handle Use Front Holes to S[...]

15 STEP 9A INST ALL OVERLA Y P ANELS • There are two sets of holes in the handle side trim. Replace handle side trim by installing the original screws in the REAR screw holes. • Secure the handle to the door using the FRONT screw holes. • Follow the same procedures to install the drawer panel. Custom handles If you are using custom handles, t[...]

16 STEP 10 CONNECT W A TER SUPPL Y • Locate and bring tubing to the front of the cabinet. • T urn the water on to flush debris from line. Run about a quart of water through tubing into a bucket, then shut off water . Copper T ubing: • Slip a 1/4" nut and ferrule (provided) over both ends of the copper tubing. Insert tube into the union f[...]

17 Installation Instructions STEP 13 INST ALL TOEKICK • Locate the supplied toekick (shipped taped to the side of the refrigerator). Install with 2 screws provided, adjust to desired height and tighten screws. • A custom toekick can be installed to match or complement the surrounding cabinetry . Use the supplied toekick as a template to cut out[...]

18 Notes[...]

19 Notes[...]

Pub. No. 49-60136-2 Dwg. No. 164D4371P001 11-03 JR 15421-1 NOTE: While performing installations described in this book, safety glasses or goggles should be worn. For Monogram ® local ser vice in your area, call 1.800.444.1845. NOTE: Product improvement is a continuing endeavor at General Electric. Therefore, materials, appearance and specification[...]