Global Machinery Company BG834HPL инструкция обслуживания

INSTRUCTION MANU AL 150mm (6") 1/2HP / 200mm (8") 3/4HP Bench Grinders • Melbourne • Perth • Auckland • Hong K ong • Shanghai • T aipei • New Y ork • V erona • London • P aris BG612HPL BG834HPL 031222 ED7 DR[...]

Contents W arranty 2 Introduction 3 Environment al protection 3 Description of s ymbols 3 Specifications 3 Safety instructions 4 A dditional safety rules f or bench grinders 6 Unpacking 6 Connecting to the po wer supply 6 Know y our product 7 Fitting and adjusting the ey e shields 8 Fitting and adjusting the spark deflectors 8 Fitting the tool r es[...]

Description of s ymbols The rating plate on your tool may show symbols. These represent important information about the product or instructions on its use . W ear hearing protection. W ear eye protection. W ear breathing protection. Conforms to relevant standards f or electromagnetic compatibility. Specifications Nominal voltage: 230 – 240V ac ~ [...]

Safety instructions The tool must be used only for the prescribed purpose . Any uses other than those mentioned in this manual will be considered a case of misuse . The user and not the manufacturer shall be liable f or any damage or injury resulting from such cases of misuse . To use this tool properly , you must observe the safety regulations, th[...]

8. Use safety accessories. Safety glasses and earmuff s should always be worn. A face or dust mask is also required. 9. Do not abuse the pow er cord. Never pull the cord to disconnect the tool from the power point. Keep the cord away from heat, oil and sharp edges. 10. Secur e the work piece . Use clamps or a vice to hold the work piece . It is saf[...]

A dditional safety rules for bench grinders • Always remove the plug from the mains socket before making any adjustments or maintenance , including changing the wheel. • Always wear eye protection and check that the eye shields on the grinder are properly adjusted. • Always turn the grinder off when it is not in use and never leave it unatten[...]

Know y our product Before using the bench grinder , familiarise yourself with all the operating features and safety requirements. The GMC Bench Grinders are designed for light to moderate duty applications in a home environment. They are not intended for use by trade persons . They are ideal f or sharpening tools such as drill bits and chisels. The[...]

8 Caution. During use it is important not to overload the grinder . The grinder should run at close to full speed. If you are applying too much pressure the grinder will start to slow down. Under these conditions, remove the part being ground and allow the grinder to return to full speed. Re-apply the part to the grinder , but with a little less fo[...]

Note . The tool rests are right and left handed. Follow the diagrams to ensure the correct tool rest is fitted to the correct side . Important. Prior to fitting the tool rests , ensure the grinder is turned off and the power plug is removed from the socket. 1. Remove the lower screw on the wheel guard (11). 2. Hold the tool rest (10) in the correct[...]

Operation Important. Prior to using the grinder , check that the eye shields, spark deflectors , and tool rests are fitted and correctly adjusted and that you are wearing safety gear including eye , hearing and breathing protection. 1. Turn the wheel by hand to mak e sure it does not touch the guard, eye shields, spark deflectors or tool rests and [...]

Fitting a wire wheel Y our bench grinder is capable of fitting a wire wheel instead of a grinding wheel. When fitting a wire wheel ensure the wire wheel is the correct size for the grinder and also ensure the bore size o f the wheel is correct for the spindle o f the grinder . Refer to the specification section of this manual f or grinding wheel an[...]

Cleaning 1. K eep the outside of the grinder clean by brushing grinding dust and dirt away from all areas where the dust tends to build up. Wear eye protection when brushing. 2. Wipe the guards and grinder with a so ft damp cloth. A mild detergent can also be used. 3. Wipe the eye shields with a so ft damp cloth, making sure not to scratch the surf[...]

Carefully read the entire Instruction Manual before using this product. Before returning this product for a Warranty Claim or any other reason Please Call 1300 880 001 (Australia) or 0800 445 721 (New Zealand) When you make your call, please have the following information at hand: • GMC Product Type • GMC Product Code A GMC Service Engineer wil[...]