Global Machinery Company DP250LS инструкция обслуживания

1 1/3 HP 5 SPEED DRILL PRESS WITH REDEYE ® DP250LS INSTRUCTION MANUAL Black Cy an Magenta Y ellow Code: DP250LS Date: 071120 Edition: 05 Op: DCR[...]

2 Contents W arranty 2 Introduction 3 Environmental protection 3 Description of symbols 3 Specifications 3 Safety rules for laser lights 4 General safety instructions 4 Additional safety rules for drill presses 5 Unpacking 7 Required tools 7 Assembly time 7 Components 7 Know your product 8 Assembly 9 Adjusting the table height 9 Adjusting the table[...]

3 Descr iptio n of sy mbols The ratin g pl ate on you r tool may sh ow sym bol s. The se rep resent imp ortant info rma tion abo ut the pro duc t or ins tru cti ons on its use . We ar he ari ng pro tec tio n. We ar ey e prot ection . We ar br eat hing pro tectio n. Con for ms to re lev ant stand ard s for elect romagn etic com pat ibi lity . Speci [...]

4 Safet y rules for laser light s The laser lig ht/las er radia tio n used in th e GMC REDEY E ® sys tem is Clas s 2 with maxi mum 1mW pow er and 650 nm wav ele ngt hs. T hese las ers do not no rma lly prese nt an opt ica l haza rd, alth ough sta ring at th e beam may cau se fla sh bli ndness . W ARNI NG. Do not st are dire ctly at th e las er bea[...]

5 7. Dre ss cor rectly . Do no t wear loo se cloth ing or jewe lle ry . The y can be caug ht in mo vin g part s. Ru bbe r glov es and non-s lip foot wea r are re com men ded when wo rki ng out doo rs. If you hav e lo ng hair , wear a pro tec tive hai r cov eri ng. 8. Use safet y ac cessor ies. Saf ety glass es and ear muf fs sho uld alway s be wor [...]

6 5. A lway s ke ep hands out of th e pat h of the drill bit. Av oid awk war d hand posi tio ns whe re a sud den slip coul d caus e you r hand to mo ve in to the dril l bit. 6. D o not in sta ll or us e any dr ill bit tha t exc eed s 175m m (7 in ches ) in len gth or ext end s more than 150mm (6 in ches ) be low the ch uck jaws. The y can sudde nly[...]

7 Unpac king Due to mode rn ma ss pro duc tio n tech niques , it is un lik ely tha t your GMC Pow er T oo l is fau lty or that a part is missi ng. If yo u find anyt hing wro ng, do not opera te the too l unti l the par ts hav e be en repla ced or the fa ult has bee n rect ified. Fai lur e to do so could resu lt in se rio us per sonal in jur y . Req[...]

8 Know your pr oduct 1. L aser lig ht on/of f switc h 2. L aser ape rture (x 2) 3. O n/of f switc h 4. P ulle y co ver 5. P ulle y co ver knob 6. B ase 7. C olum n 8. T abl e/S upp ort Ass embl y 9. T abl e Lock 10. Be lt (x 1) 1 1. Belt T ensio n Knob 12. Ke yed Chuck 13. Mo tor Head 14. Fe ed Ha ndle 15. De pth Scale 16. De pth Locki ng Knob 17. [...]

9 Assem bly 1. Pl ace ba se (6 ) on flo or . 2. Pl ace co lum n asse mbly (7) on bas e and al ign the 3 hol es in the colum n as sembly wit h th e hol es in th e bas e. 3. Us ing th e 3 bolt s se cure the colum n su pport to the bas e and ti ght en wit h a 13m m wren ch. 4. Fi t the ta ble (8) ove r the col umn and sec ure to the col umn using the [...]

1 0 2. T ilt the tab le to the des ired ang le as in dic ate d on the bev el sca le. 3. T ight en the scre w unde r the table by ro tat ing it in a clo ckw ise direc tio n. Not e. Whe n th e ta ble is til ted the wor kpi ece shoul d be cla mped to the table . Insta lling and remov ing drill bits CAU TIO N. Alwa ys ens ure that the drill pre ss is s[...]

1 1 Chang ing the speed of the drill press The speed of th e dri ll pre ss is deter min ed by the siz e of the pulle y st eps that the bel t is at tach ed to. Usi ng a sma lle r pul ley step on the fro nt pu lle y mean s a fast er drill spee d; usi ng a lar ger pull ey ste p on th e fron t pul ley means a slow er dri ll spe ed. The bel ow table ind[...]

1 2 T urning on the REDEYE ® laser line generato r 1. T he RE DEYE ® la ser line gen era tor emits two int ense nar row beams of pure red lig ht tha t in tersec t at the dri lli ng poi nt. 2. T he in ters ection is cle arly vis ibl e and wi ll not be obs cur ed by du st. It impr ove s ope rat or dr ill ing v isio n, enab les fas ter set-u p, in c[...]

1 3 Wo od drillin g • For maxim um perfo rma nce , use hi gh sp eed st eel bits for wood dr ill ing . • Sec ure the wor kpi ece to prev ent it from turn ing whe n dril ling. • Whe n dril ling thr oug h hole s, place a block of woo d beh ind the wor kpi ece to prev ent ragge d or sp lint ered edg es on th e bac k side of the ho le. Metal drill[...]

1 4 T roubl e shooting W ARNI NG. T urn the on/of f switc h to the of f positi on and unp lug the too l from the po wer su ppl y befo re perfo rmi ng tro uble sho oti ng pro ced ure s. T roubl e shooting Pro ble m Cau se S olu tio n Dri ll pre ss will no t star t Pow er cor d no t pl ugged in Ens ure that th e cor d is con nec ted to the power sup [...]

1 5[...]

GMC customer assist If your product needs repairing, replacing, technical service or you simply need help or advice, please contact us on our Customer Assist Line 1300 880 001 (Australia) or 0800 445 721 (New Zealand). For prompt service we suggest you log your service request online at www .gmcservice.com.au . Should you not have access to the Int[...]