Global Machinery Company POL1450 инструкция обслуживания

POL1450 030901 Ed8 DR[...]

Contents W arranty 2 Introduction 3 Environment al protection 3 Description of s ymbols 3 Specifications 3 Safety instructions 4 Additional safety rules f or sanders 5 Additional safety rules f or angle grinders 6 Additional safety rules f or polishers 7 Accessories 7 Unpacking 7 Know y our product 8 Setting up 9 Operation in grinder mode 9 Operati[...]

Description of s ymbols The rating plate on your tool may show symbols. These represent important information about the product or instructions on its use . Wear hearing protection. Wear eye protection. Wear breathing protection. Double insulated for additional protection. Conforms to relevant standards f or electromagnetic compatibility. Specifica[...]

Safety instructions The tool must be used only for the prescribed purpose . Any uses other than those mentioned in this manual will be considered a case of misuse . The user and not the manufacturer shall be liable f or any damage or injury resulting from such cases of misuse . T o use this tool properly , you must observe the safety regulations, t[...]

9. Connect dust extr action equipment. If devices are provided for the connection o f dust extraction and collection facilities , ensure that these are connected and properly used. 10. Do not abuse the po wer cor d. Never pull the cord to disconnect the tool from the power point. Keep the cord away from heat, oil and sharp edges. 11. Secur e the wo[...]

6 • Check the disc before mounting it into the angle grinder . Check by striking it with a wooden handle whilst balancing the disc on your finger . Listen for the ring and do not use if dull, as the disc may be cracked. • When the disc is installed, run it for at least one minute to ensure that it does not have a fault. It is always advisable t[...]

• When sanding wood, always connect the dust bag or use a dust extraction system. • Before using the sander with metal, always remove the dust bag from the outlet as sparks may ignite the dust or the bag. • Do not continue to use worn, torn or heavily clogged sanding discs. • Do not touch the moving sanding disc. • Ensure that you have re[...]

Know y our product Before using the polisher , familiarise yourself with all the operating features and safety requirements. Use the tool and accessories only for the applications intended. All other applications are expressly ruled out. 1. Motor housing 2. Spindle lock button 3. V ariable speed dial 4. Rear handle 5. Soft grip 6. Mounting points f[...]

Setting up Multi position front handle Screw the multi position front handle (9) into the most suitable mounting point (6) (left side , right side or at the top) to suit the task on hand. V ariable Speed The POL1450 is fitted with a variable speed dial (3) that allows you to adjust the speed to suit the application and material. The tool operates b[...]

9. T o tighten, press and hold the spindle lock button (2) and using the pin wrench tighten the outer flange . 10. Turn the new disc by hand, ensuring that it is tight in the flanges and that it rotates fully and does not wobble unduly. 11. Run the angle grinder at no load for at least one minute to ensure the new disc is in good condition. Make su[...]

11 Operation in sander mode Fitting the Sandpaper Switch off the tool and disconnect it from the power supply. 1. The GMC grinder/sander/polisher is fitted with a hook & loop base allowing easy changing of accessories . Ensure there are no debris left in the hooks & loops o f the disc before fitting accessories. 2. Align the sandpaper with [...]

12 Operation in polisher mode Prepar e the surface For best results, the surf ace should be clean and dry. Most high-gloss surfaces can be cleaned with a mild soap and water solution. For removal of stubborn dirt stains such as road tar , grease, and bug stains , you can use a mild ammonia solution such as that used in glass cleaners. Before using [...]

sponge , polishing bonnet and the tool are in good condition. Plug the cordset into the mains socket. 3. Do not overload the tool so that the disc slows down. Let the tool do the work rather than applying pressure . The weight of the tool alone provides sufficient pressure . 4. Hold the tool securely and make sure that you have full control at all [...]

14[...]

15[...]

Carefully read the entire Instruction Manual before using this product. Before returning this product for a Warranty Claim or any other reason Please Call 1300 880 001 (Australia) or 0800 445 721 (New Zealand) When you make your call, please have the following information at hand: • GMC Product Type • GMC Product Code A GMC Service Engineer wil[...]