Goodman Mfg 000 &12 инструкция обслуживания

Important Safety Instructions The following symbols and labels are used throughout this manual to indicate immediate or potential safety hazards. It is the owner’s and installer’s responsibility to read and comply with all safety information and instructions accompanying these symbols. Failure to heed safety information increases the risk of pe[...]

2 CONTENTS Important Safety Instructions .............................................. 1 Shipping Inspection ............................................................ 1 Codes & Regulations ......................................................... 2 Installation Considerations ................................................. 2 Rooftop Insta[...]

3 • Select a location where noise, vibration and hot dis- charged air will not be an issue. • Do not install where high frequency equipment is used (wireless equipment, welding machine, medical facility) as it may interfere with the unit’s operation. Rooftop Installations If it is necessary to install the outdoor unit on a roof structure, ens[...]

4 NOTE: Install the mounting bracket and drill the holes in the wall according to the wall structure and the correspond- ing mounting points on the mounting bracket. (The mounting brackets vary according to the model.) Inco rrect o rie ntation of Inst al lat ion Pl ate Corr ect orienta tion of Inst al lat ion Pl ate Figure 4 4. Determine the hole p[...]

5 Indoor Unit Installation 9. Pass the piping through the hole in the wall. 10 . Place the upper claw on the back of the indoor unit on the upper hook of the installation plate. Move the indoor unit from side to side to ensure it is securely mounted. (See Figure 10 ). NOTE: By placing cushioning material between the in- door unit and the wall, plac[...]

6 1 H Figure 14A 2 W 1 W 2 Figure 14B MS* 9 & MS * 12 Ou tdo o r Un it Dimen sion s Inc hes /mm ( L1x Hx W1) L2 ( mm) W 2 ( mm) 30" x 23" x 11" 760 x 590 x 285 21" 530 11 1/ 2" 290 M oun tin g Di me n s ions Drain joint installation NOTE: Drain joints differ slightly according to the different outdoor units. Inspect you[...]

7 2. Insert tube in flare tool to measurement “A” in chart. Flare tubing as shown in Figure 19. Make sure flare is free of burrs and completely formed to make a leak proof joint. NOTE: In order to avoid dropping burrs into the tubing, angle the end of the copper tube/pipe in a downward direction as you remove the burrs. Pi pe Rea mer Point down[...]

8 IMPORTANT NOTES: • If there are safety issues concerning the power supply, the unit should not be connected until safety issues are resolved. • Ensure that the electrical power supply is sufficient to safely power and run the unit. • Power voltage should range for 90% - 110% of the rated voltage. • Main power switch and surge protector sh[...]

9 T erminal s on the indoor un it L N S L N S Model A T er minals on t he i n d o or u ni t L N S Te r m i n a l s o n the outdoor un i t 1 ( L ) 2 ( N ) S L N Pow er sup pl y Model B 3. Secure the wire onto the control board with the cord clamp. 4. To prevent the ingress of water, form a loop of the con- nective wires as illustrated in the install[...]

10 • When relocating the unit to another place, perform the evacuation using a vacuum pump. • Refrigerant added to the unit must be in liquid form. (Does not apply to units using R-22.) Safe Refrigerant Handling While these items will not cover every conceivable situation, they should serve as a useful guide. Refri ger ants are hea vier th an a[...]

11 T est Running After completing the gas leak check at the flare nut connec- tions and electrical safety check, perform the test operation. • Ensure all tubing and wiring have been properly con- nected. • Make sure both the gas and liquid side service valves are fully open. 1. Connect the power; press the ON/OFF button on the re- mote control [...]

12 Goodman Manufacturing Comp any , L.P . 5151 San Felipe, Suite 500, Houston, TX 77056 www .goodmanmfg.com © 201 1 Goodman Manufacturing Company , L.P .[...]