Graco Inc. 309273 инструкция обслуживания

Ultra Max t Electric Airless Sprayers Operating Instructions The intent of these instructions is to provide the new painter with a quick and easy reference to become familiar with airless sprayers. This does not replace the Instruction Manual supplied with this sprayer . Read and understand the instructions and warnings in that manual. Important No[...]

2 309273 PRESSURE RELIEF – Do this when cleaning, repairing or shuting down sprayer WASTE RESÍDUOS À JETER DESECHO 1. T urn pressure to lowest setting. T urn power OFF . Unplug sprayer . 2. T rigger gun to relieve pressure. 3. Put drain tube in pail . T urn prime valve down. W ARNING Fire and explosion hazard: Solv ent and pa i nt f um es c an [...]

3 309273 Power Switch Pressure Control Component Identification Suction T ube Filter Prime V alve Prime/drain position Paint position Spray Gun T rigger Safety Put trigger safety ON when not spraying. T ake trigger safety OFF before triggering gun. Digital Display (Not available on all models) 15/20A Switch AutoClean V alve (Not available on all mo[...]

4 309273 1. Connect Graco airless hose to sprayer . T ighten securely . 2. Connect other end of hose to gun. Setup 3. T ighten securely . 4. Remove tip guard.[...]

5 309273 5. Check inlet strainer for clogs and debris. 6. Fill throat packing nut with TSL to prevent premature packing wear . Do this each time you spray . Approximate Fill Level[...]

6 309273 P AINT FLUSH 7. T urn power OFF . 8. Plug power supply cord into a properly grounded electrical outlet. 9. T urn prime valve down. 10. Place suction tube and drain tube in grounded metal pail partially filled with flushing fluid. Attach ground wire to pail and to true earth ground. Do 1 . – 5 . of Startup to flush out storage oil shipped[...]

7 309273 FLUSH Note: Inspect fittings for leaks. Do not stop leaks with your hand or a rag! If leaks occur , do Pressure Relief . T ighten leaky fittings. Repeat Startup, 1. – 5 . If no leaks, continue to trigger gun until system is thoroughly flushed. Proceed to 6. Startup 15 SEC 1. T urn prime valve down. T urn pressure control to lowest pressu[...]

8 309273 FLUSH P AINT General Surfaces T ip Recommendations Chart Wood Interi or C ab- inets , Paneling Interior Walls or Ceilings Dry wall, Plaster Ov er Hang Su rfaces Materi als Filter Mesh 6–8 8–10 10–12 12–14 Orific e Size (in. ) Fan Widt h ( in.) at 12 in . Masonr y Bl ock, Stu cco, Co ncre te Wood Ex terior Shingle, Siding, Shiplap O[...]

9 309273 SwitchTip and Guard Assembly 1. Insert SwitchT ip. Insert seat and OneSeal. 2. Screw assembly onto gun. Hand tighten. SwitchT ip OneSeal seat Press SMARTCONTROL button to cycle through PRESSURE – GAL/L TR – TIMER displays D PRESSURE : Fluid pressure at the sprayer D GAL/L TR : Accumulated total of gallons/liters sprayed D TIMER : Durat[...]

10 309273 Spray T est Pattern heavy edges Clearing Tip Clogs 1. T rigger gun and spray test pattern. Slowly adjust pressure to eliminate heavy edges. Use smaller tip size if pressure adjustment can not eliminate heavy edges. 2. Hold gun perpendicular , 10–12 in. (25–30 cm) from surface. Spray back and forth. Use strokes overlapped by 50%. Start[...]

11 309273 Cleanup P AINT 1. T urn power OFF . 2. T urn pressure to lowest setting. T rigger gun to relieve pressure. 3. T urn prime valve down. 4. Remove filter assembly and assemble gun without filter . Perform AutoClean procedure (Manual 309278) or follow conventional flushing/cleaning procedure that follows: ti2874a Contractor Contractor II[...]

12 309273 5. Remove guard and SwitchT ip. 6. Clean filter , guard and SwitchT ip in flushing fluid. P AINT FLUSH 7. Remove siphon tube set from paint and place in flushing fluid. Use water for water base paint and mineral spirits for oil base paint. 8. If sprayer has a filter , unscrew bowl, remove filter . Assemble without filter . Clean filter . [...]

13 309273 P AINT FLUSH 9. T urn power ON. 10. T urn prime valve hori- zontal. 1 1. Hold gun against paint pail. T ake trigger safety OFF . T rigger gun until flushing fluid appears. 12. Move gun to flushing pail, hold gun against pail, trigger gun to thoroughly flush system. Release trigger and put trigger safety ON. 13. T urn prime valve down and [...]

14 309273 P AINT FLUSH FLUSH 14. Raise siphon tube above flushing fluid and run sprayer for 15 to 30 seconds to drain fluid. T urn power OFF . 15. Make sure plastic center tube is tightened securely . Install filter bowl and filter . Hand tighten filter bowl. Install filter assembly into gun. Hand tighten gun handle. 16. Wipe sprayer , hose and gun[...]

15 309273 T rouble Shooting TYPE OF PROBLEM WHA T TO CHECK If check is OK, go to next check WHA T TO D O When check is not OK refer to this column D Sprayer does not respond 1. Check if error code is displayed, page 9. 1. Refer to your repair manual. D Sprayer will not prime or takes too long to prime 1 . Air in paint pump 1. Open prime valve to pu[...]

16 309273 Daily: Inspect, clean and replace as needed D Manifold filter , gun filter and inlet stainer D W et cup for leakage, tighten if needed D TSL level D Gun trigger safety D T ip wear , replace if necessary D Electric cord and plug W eekly: D Check tightness of wet cup. D Inspect all high pressure paint hoses. Annually: D Schedule maintenance[...]