Grizzly G6049 инструкция обслуживания

COPYRIGHT © MAY, 2002 BY GRIZZLY INDUSTRIAL, INC. 1821 VALENCIA ST., BELLINGHAM, WA 98227 WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. PRINTED IN TAIWAN ONLINE MANUAL DISCLAIMER THE INFORMATION IN THIS MANUAL REPRESENTS THE CONFIGURATION OF THE MACHINE AS IT IS C[...]

For Your Own Safety Read Instruction Manual Before Operating This Equipment Indicates an imminently hazardous situation which, if not avoided, WILL result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, COULD result in death or serious injury. Indicates a potentially hazardous situation which, if not a[...]

G6049 14/15 Gauge Angle Finish Nailer Kit -2 - 10. USE PROPER AIR HOSE for the tool. Make sure your air hose is in good condition and is long enough to reach your work without stretching. 11. WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neck- ties, rings, bracelets, or other jewel- ry which may get caught in moving parts. Non-slip footw[...]

G6049 14/15 Gauge Angle Finish Nailer Kit -3 - Operating this nailer can propel objects into the air, causing immedi- ate eye damage. To protect yourself, always wear American National Standards Institute (ANSI) approved safety glasses or goggles when oper- ating this equipment. In addition, this nailer discharges at 85-90 decibels. To protect your[...]

G6049 14/15 Gauge Angle Finish Nailer Kit -4 - INTRODUCTION Commentary Most important, we stand behind our tools. If you have any service questions or parts requests, please call or write us at the location listed below. Grizzly Industrial, Inc. 1203 Lycoming Mall Circle Muncy, PA 17756 Phone: (570) 546-9663 Fax: (800) 438-5901 E-Mail: techsupport@[...]

G6049 14/15 Gauge Angle Finish Nailer Kit -5 - Compressed Air System Safety Yoke Mechanism The safety yoke is a mechanical device that can fail. Never rely on the safety yoke mechanism as an excuse to point the nailer at yourself or any bystanders. Serious injury may occur. Exceeding the maximum permissible operating pressure may cause the nailer t[...]

G6049 14/15 Gauge Angle Finish Nailer Kit -6 - OPERATION Loading Nailer To load your nailer: 1. Disconnect the air supply from the nailer! 2. Load nails at the top of the magazine in the T-slot as shown in Figure 1 . 3. Slide the stick of nails all the way down to the nose of the nailer. 4. Pull the magazine pusher all the way back, then let it com[...]

G6049 14/15 Gauge Angle Finish Nailer Kit -7 - Operating Nailer Adjusting Depth Besides damaging your workpiece, deflection can cause injury if your free hand is securing the workpiece in the location that the nail deflects. 4. Press the trigger. If the nail drove into the wood far enough, continue with your intended operations. If the nail either [...]

G6049 14/15 Gauge Angle Finish Nailer Kit -8 - Always disconnect air from nailer whenever clearing a jammed nail! Clearing Jammed Nails The most frequent situation with any type of nailer is a nail jam. A jammed nail must be cleared before using the nailer again. Figure 5. Removing guide cover. Quick Release Latch Driver Guide Cover To clear a jamm[...]

G6049 14/15 Gauge Angle Finish Nailer Kit -9 - Cleaning Nailer Use a good solvent to clean the nose assembly of the nailer. Always be sure that the nailer is dry before using it again. Do not allow dust, chips, sand, etc. into the air connectors or into the body of the nail- er; this may result in leaks and damage to the nailer and the air fittings[...]

G6049 14/15 Gauge Angle Finish Nailer Kit -10 - Replacing Pistons/O-Rings If you use your nailer day in and day out, Grizzly offers repair pistons as cheap insurance against wasted down time and lost profits in the event that a piston or pis- ton shaft becomes worn out. To replace a piston: Figure 7. Removing nailer exhaust cap. 8. With a long flat[...]

G6049 14/15 Gauge Angle Finish Nailer Kit -11 - G6049 PART BREAKDOWN 93 7 33 12 14 13 11 10 9 7A 8 24 23 22 35A 20 49 5 50 30A 29 51 52A 6 5A 3 2 92 19 18 27 25 26 60 63 77 76A 66A 1 65 53 55 67A 54 76A 86 90 68A 64 69 69 88 76A 31 34 69 32 28 70 57 56A 58 59 92A 71 74 72 62 60 16A 29-1 69 48A 45B 39 44 47A 42 83 43 41 46 40 38 37 36 92A 20 15A 21[...]

G6049 14/15 Gauge Angle Finish Nailer Kit -12 - 01 P6049001 LOCK NUT 02 P6049002 EXHAUST COVER 03 P6049003 SPRING PLATE 05A P6048005A CAP SCREW SW 06 P6049006 CAP 07A P6048007A BUT TON HD CAP SC R 08 P6049008 SPACER 09 P6049009 PISTON STOPPER 10 P6049010 SPRING 11 P6049011 O-RING 12 P6049012 PISTON HEAD VALVE 13 P6049013 O-RING 14 P6049014 SEAL 15A[...]

TROUBLESHOOTING Air leaking at trigger valve area. Air leaking between hous- ing and hose. Air leaking between hous- ing and cap assembly. Tool skips nails while dis- charging. Tool runs slowly or has a loss of power. Fasteners frequently jam the nailer. Nailer does not fire. 1. O-rings must be replaced & operation of safety yoke must be checke[...]

G6049 14/15 Gauge Angle Finish Nailer Kit -14 - Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of main- tenance. This is Griz[...]

Name __________________________________________________________ Street __________________________________________________________ City ____________________ State ________ Zip _________ Phone Number ____________ E-Mail ___________________ FAX ____________ Model # _______________Serial#________________ Order # ______________ The following information[...]

FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT NAIL Name________________________________ Street________________________________ City______________State______Zip_______ Send a Grizzly Catalog to a friend: Place Stamp Here[...]