HAMPTON BAY H35-LP1 инструкция обслуживания

FPI FIREPLACE PRODUCTS INTERNA TIONAL L TD. 6988 V enture St., Delta, BC Canada, V4G 1H4 W ARNING: If the information in these instructions are not followed ex- actly , a fi re or explosion may result causing property damage, personal injury or loss of life. FOR YOUR SAFETY Do not store or use gasoline or other fl ammable vapors and liquids in th[...]

2 Hampton ® H35 Direct V ent Freestanding Gas Stove HAMPT ON ® Direct V ent Freestanding Gas Stove UNIT DIMENSIONS T o the New Owner: Congratulations! Y ou are the owner of a state-of-the-art Hampton ® Gas Stove by FPI FIREPLACE PRODUCTS INTERNA TIONAL L TD. The H35 is a hand crafted appliance and has been designed to provide you with all the wa[...]

Hampton ® H35 Direct V ent Freestanding Gas Stove 3 T ABLE OF CONTENTS Optional Brick Panel .................................................... 33 Log Set Installation ...................................................... 33 Double DoorInstallation ............................................... 35 Decorative Door Grill Installation ............[...]

4 Hampton ® H35 Direct V ent Freestanding Gas Stove This is a copy of the label that accompanies each Direct V ent Freestanding Gas Stove. We have printed a copy of the contents here for your review . SAFETY LABEL NOTE: Hampton ® units are constantly being improved. Check the label on the unit and if there is a difference, the label on the unit i[...]

Hampton ® H35 Direct V ent Freestanding Gas Stove 5 REQUIREMENTS 5.08: Modifica tions to NFPA-54, Chap ter 10 (2) Revise 10.8. 3 by adding the following a dditional requi rements: (a) For all side wall hor izontally ve nted gas fueled e quipment insta lled in every dwelling, bui lding or str ucture used in whole or in part for residential pu rpose[...]

6 Hampton ® H35 Direct V ent Freestanding Gas Stove IMPORT ANT MESSAGE SA VE THESE INSTRUCTIONS The Direct V ent Freestanding Gas Stove must be installed in accordance with these instructions. Carefully read all the instructions in this manual fi rst. Consult the building authority having jurisdiction to determine the need for a permit prior to s[...]

Hampton ® H35 Direct V ent Freestanding Gas Stove 7 INST ALLA TION GENERAL SAFETY INFORMA TION 1) The appliance installation must conform with local Canadian Electrical Code. 2) The appliance when installed, must be electrically grounded in accordance with local codes, or in the absence of local codes with the current National Electrical Code, ANS[...]

8 Hampton ® H35 Direct V ent Freestanding Gas Stove OPTIONAL F AN INST ALLA TION Diagram 1 Diagram 2 LOCA TING YOUR GAS ST OVE When selecting a location for your stove, ensure that the clearances listed above are met as well as ensuring that there is adequate accessibility for servicing and proper operation. MANUF ACTURED MOBILE HOME ADDITIONAL RE[...]

Hampton ® H35 Direct V ent Freestanding Gas Stove 9 INST ALLA TION INST ALLA TION PRECAUTIONS These venting systems are engineered products that have been designed and tested for use with the H35-NG1, and H35-LP1. The warranty will be voided and serious fi re, health or other safety hazards may result from any of the fol- lowing actions: 1) Insta[...]

10 Hampton ® H35 Direct V ent Freestanding Gas Stove EXTERIOR VENT TERMINAL LOCA TIONS A= Clea rance above grade, veranda, porch, deck, or balcony *(min. 12"/30cm) B= Clea rance to window or door that may be opened *(12"/30cm) C= Clea rance to permanently closed window *(min. 12"/30cm) D= V ertic a l clearanc e to ventilated soffi [...]

Hampton ® H35 Direct V ent Freestanding Gas Stove 11 INST ALLA TION 4” X 6-5/8” RIGID PIPE CROSS REFERENCE CHART Components from different Manufacturers may not be mixed. Not All Rigid Pipe components are available directly from FPI. Description Simpson Direct V ent Pro ® Simpson Direct V ent GS ® Discontinued Selkirk Direct-T emp™ America[...]

12 Hampton ® H35 Direct V ent Freestanding Gas Stove Description Simpson Direct V ent Pro ® Simpson Direct V ent GS ® Discontinued Selkirk Direct-T emp™ American Metal Products ® Amerivent Direct Metal-Fab ® Sure Seal Security Secure V ent ® Attic Insulation Shield 12” 46DV A-IS - N/A from FPI N/A N/A 4DAIS12 N/A SV4RSA Attic Insulation S[...]

Hampton ® H35 Direct V ent Freestanding Gas Stove 13 RIGID PIPE VENTING SYSTEMS Horizontal or V ertical T erminations Alternate Horizontal T ermination Caps INST ALLA TION Pipe Length V ertical T ermination Cap S torm Collar Flashing Ceiling Firestop 24" Pipe Length Adj.Pipe Length 1 1" - 14-5/8" 90 Elbow o Horizontal T ermination C[...]

14 Hampton ® H35 Direct V ent Freestanding Gas Stove INST ALLA TION Offset to V ertical T erminations VENTING ARRANGEMENTS V ertical T erminations Systems for Residential Manufactured and Mobile Homes The shaded area in the diagram below shows all allowable combinations of straight vertical and offset to vertical runs with vertical terminations. M[...]

Hampton ® H35 Direct V ent Freestanding Gas Stove 15 VENTING ARRANGEMENTS HORIZONT AL TERMINA TIONS USING RIGID PIPE Dura-V ent Snorkel T ermination Riser V ent T ermination The two diagrams show all allowable com- binations of straight horizontal termination using Rigid Pipe. Restrictor position "A". V enting Arrangements -Straight Hori[...]

16 Hampton ® H35 Direct V ent Freestanding Gas Stove Horizontal V enting with T wo (2) 90 o Elbows Option V H + H1 A) 3' Min. 2' Max. B) 4' Min. 3' Max. C) 5' Min. 4' Max. D) 6' Min. 5' Max. E) 7' Min. 6' Max. F) 8' Min. 8' Max. Horizontal V enting with T wo (2) 90 o Elbows Option H V H +[...]

Hampton ® H35 Direct V ent Freestanding Gas Stove 17 H1 H V V ertical V enting with T wo (2) 90 o Elbows Option V H V + V1 A) 1' Min. 3' Max. 2' Min. B) 2' Min. 4' Max. 3' Min. C) 3' Min. 5' Max. 4' Min. D) 4' Min. 6' Max. 5' Min. E) 5' Min. 7' Max. 6' Min. V ertical V enti[...]

18 Hampton ® H35 Direct V ent Freestanding Gas Stove V enting Arrangements - V ertical T erminations with Co-linear Flex System for both Residential & Manufactured Homes into Masonry Fireplaces The shaded area in the diagram shows the allowable vertical terminations. Note: Must remove 4 screws from stove collar and rotate 180 o to have collar [...]

Hampton ® H35 Direct V ent Freestanding Gas Stove 19 Review the following sequence of instructions which are typical of most installations. The se- quence may vary depending on wall thickness. See "Exterior V ent T erminal Locations" to "V enting Arrangements" section for vent location and clearance dimensions, and the "V [...]

20 Hampton ® H35 Direct V ent Freestanding Gas Stove INST ALLA TION Note: Th e pipe seam should be facing down. Note: T o make the installation more aes- thetically pleasing, we recommend framing out a square that the cap can be mounted on. 3) Attach the 4" dia. fl ex liner to the vent terminal ensuring that the fl ex overlaps the collar of[...]

Hampton ® H35 Direct V ent Freestanding Gas Stove 21 Alternate Horizontal T ermination Caps Dura-V ent Basic Horizontal Kit # 970 1 90 o Elbow 1 W all Thimble Cover 1 Horiz. Sq. T erm. Cap INST ALLA TION DURA-VENT TERMINA TION KIT Planning Y our Dura-V ent Installation There are two basic types of Dura-V ent Direct V ent System installations: hori[...]

22 Hampton ® H35 Direct V ent Freestanding Gas Stove Diagram 2a Diagram 3 Below Grade Snorkel Installation If the Snorkel T ermination must be installed below grade, i.e. basement application, proper drainage must be provided to prevent water from entering the Snorkel T ermination. Refer to Dura-V ent Installation instructions for details. Do not [...]

Hampton ® H35 Direct V ent Freestanding Gas Stove 23 Diagram 7 Diagram 6 Diagram 5 Diagram 4 b) The location of the horizontal vent termi- nation on an exterior wall must meet all local and national building codes, and must not be blocked or obstructed. See diagram in the "External V ent T erminal Locations" section. 4) If installing the[...]

24 Hampton ® H35 Direct V ent Freestanding Gas Stove Roof Pitch Minimum V ent Height Feet Meters fl at to 7/12 2 0.61 over 7/12 to 8/12 2 0.61 over 8/12 to 9/12 2 0.61 over 9/12 to 10/12 2.5 0.76 over 10/12 to 1 1/12 3.25 0.99 over 1 1/12 to 12/12 4 1.22 over 12/12 to 14/12 5 1.52 over 14/12 to 16/12 6 1.83 over 16/12 to 18/12 7 2.13 over 18/12 t[...]

Hampton ® H35 Direct V ent Freestanding Gas Stove 25 CONVERTING CLASS-A MET AL CHIMNEY OR MASONR Y CHIMNEY T O DIRECT VENT SYSTEM There are two different types of direct vent conversion systems listed below . Follow the appropriate directions for your installation. A) Through an existing factory built metal chimney going through the ceiling: A typ[...]

26 Hampton ® H35 Direct V ent Freestanding Gas Stove 4) Assemble the desired lengths of Black Pipe and Elbows necessary to reach from the appliance adapter up through the support box and fl ashing to proper height as per Diagram 12, local codes or the "Exterior V ent T erminal Locations" section. Ensure that all pipe and elbow connectio[...]

Hampton ® H35 Direct V ent Freestanding Gas Stove 27 GAS PIPE PRESSURE TESTING The appliance must be isolated from the gas supply piping system by closing its individual manual shut-off valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psig. (3.45 kPa). Disconnect piping from valve at pre[...]

28 Hampton ® H35 Direct V ent Freestanding Gas Stove INST ALLA TION THIS CONVERSION MUST BE DONE BY A QUALIFIED GAS FITTER IF IN DOUBT DO NOT DO THIS CONVERSION !! Each Kit contains one LPG Conversion Kit and one DC Sparker Kit. LPG Conversion Kit Contains: Qty . Part # Description 1 904-529 5/32" Allen Key 1 904-645 Burner Orifi ce #51 1 91[...]

Hampton ® H35 Direct V ent Freestanding Gas Stove 29 17) Reverse steps 4) to 2). 18) Attach clear label "This unit has been converted to LPG" near or on top of the serial # decal. 19) Replace yellow "Natural Gas" label with red "LPG" label. 14) Using the Allen wrench as shown in Fig.4, rotate the screw clockwise until[...]

30 Hampton ® H35 Direct V ent Freestanding Gas Stove 9) Install the plastic bushing over the outside of the hole. 10) Attach the ground wire to the DC spark mounting bracket. 11 ) Attach the DC sparker generator wires to the DC sparker . 8) Insert both the ground wire and the DC sparker generator wire through the hole of the DC spark heat shield. [...]

Hampton ® H35 Direct V ent Freestanding Gas Stove 31 5) Locate the ground lug at the receptical box, left of the unit. Installer Notice: These instructions must be left with the appliance. 15) Check for gas leaks. 16) Check inlet and outlet pressures. 17) Check operation of fl ame control. 18) Check for proper fl ame appearance and glow on logs.[...]

32 Hampton ® H35 Direct V ent Freestanding Gas Stove CONVERSION KIT T O LOWER BTU RA TING NA TURAL GAS - KIT #: 740-950 PROP ANE - KIT # 740-952 THIS CONVERSION MUST BE DONE BY A QUALIFIED GAS FITTER IF IN DOUBT DO NOT DO THIS CONVERSION !! Natural Gas Conversion Kit 740-950 Contains: Qty . Part # Description 1 904-240 Burner Orifi ce #37 (Natura[...]

Hampton ® H35 Direct V ent Freestanding Gas Stove 33 LOG SET INST ALLA TION Read the instructions below carefully and refer to the diagrams. If logs are broken do not use the unit until they are replaced. Broken logs can interfere with the pilot operation. The gas log kit contains the following: a) 02-43 Rear Log b) 02-56 Middle Left Log c) 02-44 [...]

34 Hampton ® H35 Direct V ent Freestanding Gas Stove C)02-44 Pins on Rear Log Support A)02-43 B)02-56 4) Place Rear Log A)02-43 on the two pins on the rear log support. 5) Place the Middle Left Log B)02-56 on the two pins as shown. 6) Sprinkle some lava rock just in front of B) 02-56 on the burner holes. 7) Place Front Left Log C)02-44 onto the 2 [...]

Hampton ® H35 Direct V ent Freestanding Gas Stove 35 INST ALLA TION DOUBLE DOOR INST ALLA TION 1) Secure the T op Door Clip into the T op Front Casting. Rear View of Decorative Door Grill To p C l i p Bottom Clip Bottom Clip DECORA TIVE DOOR GRILL INST ALLA TION 1) Hook the T op Clip on the Decorative Door Grill into the top lip of the Front Casti[...]

36 Hampton ® H35 Direct V ent Freestanding Gas Stove INST ALLA TION DOOR HINGE REMOV AL 1) Remove the cast top by lifting it off of the stove. 2) Release the catches on the left and right side of the stove that secure the glass. 3) Remove the glass by sliding it up and out. 4) Pull all four door hinges out from the sides of the front casting. Rele[...]

Hampton ® H35 Direct V ent Freestanding Gas Stove 37 WIRING DIAGRAMS CAUTION: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. If any of the original wires as supplied with the appliance must be replaced, it must be replaced with CSA type SEW (200 o C) or its equivalent. This[...]

38 Hampton ® H35 Direct V ent Freestanding Gas Stove REMOTE CONTROL Use the Hampton ® Remote Control Kit approved for this unit. Use of other systems may void your warranty . The remote control kit comes with a hand held transmitter , a receiver and a wall mounting plate. W ALL THERMOST A T A wall thermostat may be installed if desired. Connect t[...]

Hampton ® H35 Direct V ent Freestanding Gas Stove 39 OPERA TING INSTRUCTIONS OPERA TING INSTRUCTIONS 1) Read and understand these instructions before operating this appliance. 2) Check to see that all wiring is correct and enclosed to prevent possible shock. 3) Check to ensure there are no gas leaks. 4) Make sure the glass in the door frame is pro[...]

40 Hampton ® H35 Direct V ent Freestanding Gas Stove COPY OF THE LIGHTING PLA TE INSTRUCTIONS OPERA TING INSTRUCTIONS AUT OMA TIC CONVECTION F AN OPERA TION The fan operates automatically - turn the knob at the top right rear corner to adjust to the desired speed. The fan will turn on as the stove comes up to operating temperature. After the unit [...]

Hampton ® H35 Direct V ent Freestanding Gas Stove 41 MAINTENANCE T op View of pilot fl ame MAINTENANCE INSTRUCTIONS 1) Always turn off the valve before cleaning. For relighting, refer to lighting instructions. Keep the burner and control compartment clean by brushing and vacuuming at least once a year . When cleaning the logs, use a soft clean pa[...]

42 Hampton ® H35 Direct V ent Freestanding Gas Stove T o remove fan: 1) Unplug or disconnect power source to stove. 2) Remove the 6 screws holding the access panel in place. F AN MAINTENANCE If your fan requires maintenance or replace- ment, access to the fan is through the rear access panel on the back of the unit. NOTE: the unit MUST NOT be oper[...]

Hampton ® H35 Direct V ent Freestanding Gas Stove 43 11 ) Carefully lift the burner tray assembly out. REMOVING V AL VE If your valve requires maintenance or replace- ment, use the following instructions: Note: Al ways close off the gas supply before removing the valve. 1) If optional fan is installed, disconnect power source to stove. 2) Remove a[...]

44 Hampton ® H35 Direct V ent Freestanding Gas Stove P ARTS LIST MAIN ASSEMBL Y 1) 942-301** Casting - T op 2) 942-31 1** Casting - T op Grill 3) 942-321** Casting - Left Side 4) 942-331** Casting - Right Side 5) 942-341** Casting - Front 6) 740-931** Casting - Double Door 8) 942-371** Casting - Bottom Skirt 9) 942-381** Casting - Leg 10) 942-391*[...]

Hampton ® H35 Direct V ent Freestanding Gas Stove 45 BURNER & LOG ASSEMBL Y 740-574/P V alve Assembly S.I.T . - Natural Gas 740-576/P V alve Assembly S.I.T . - Propane 60) 910-478 V alve S.I.T . - NG/LP 904-689 #33 Orifi ce - N.G. 904-645 #51 Orifi ce - LP 63) 910-190 Piezo Ignitor & Nut 64) 908-672 Control Panel Decal 65) 490-061 Switch[...]

46 Hampton ® H35 Direct V ent Freestanding Gas Stove NOTES[...]

Hampton ® H35 Direct V ent Freestanding Gas Stove 47 W ARRANTY Hampton Fireplace Products are designed with reliability and simplicity in mind. In addition, our internal Quality Assurance T e am carefully inspects each unit thoroughly before it leaves our facility . FPI Fireplace Products International Ltd. is pleased to extend this limited lifeti[...]

Installer: Please complete the following information Dealer Name & Address: ______________________________________________ ___________________________________________________________________ Installer: ___________________________________________________________ Phone #: ___________________________________________________________ Date Installed:[...]