Harbor Freight Tools 44836 инструкция обслуживания

ASSEMBL Y AND OPERA TING INFORMA TION 3491 Mission Oaks Blvd., Camarillo , CA 93011 Visit our W eb site at http://www .harborfreight.com Cop yright © 2001 by Harbor F reight T ools. All r ights reser ved. No por tion of this manual or any artwork contained herein may be reproduced in any shape or form without the e xpress written consent of Harbor[...]

1. KEEP WORK AREA CLEAN AND DR Y . Cluttered, damp or wet work areas invite injuries. 2. KEEP CHILDREN A W A Y FR OM W ORK AREA. Do not allow children to handle this product. 3. ST ORE IDLE EQUIPMENT . When not in use, tools and equipment should be stored in a dr y location to inhibit r ust. Alw a ys lock up tools and equipment and keep out of reac[...]

SKU 44836 P A GE 3 5. USE EYE, HEARING, AND BREA THING PRO TECTION. Wear ANSI appro v ed saf ety impact ey e glasses, ANSI appro v ed hearing protection, and ANSI approv ed dust mask or respirator when using this product. ANSI approv ed saf ety impact ey e glasses, hearing protection, and dust masks and respirators are available from Harbor F reigh[...]

sure this product is always plugged into a grounded 3-hole electrical receptacle with an appropriate breaker switch in-line. 2. MAKE SURE THE POWER SWITCH IS IN THE “OFF” POSITION BEFORE PLUGGING IN THE POWER CORD. 3. DO NO T ABUSE THE PO WER CORD . Do not use the cord to pull the 3-prong plug from a power outlet. Keep cord away from heat, oil,[...]

SKU 44836 P A GE 5 10. CAUTION: Some woods contain preservatives such as copper chromium arsenate (CCA) which can be toxic. When drilling these materials extra care should be taken to avoid inhalation and minimize skin contact. 11. ALLO W THE DRILL BIT T O SPIN UP T O FULL SPEED BEFORE DRILLING INT O THE WORKPIECE. When tur ning off the Dr ill Pres[...]

SKU 44836 P A GE 6 3. T o attac h the Head Assemb l y (par t #1B) to the Column (par t #1A) , loosen the Hex Screws (part #13B) to ensure the Screws do not protrude internally in the Column (par t #1A), as this would pre v ent the Head Assembly from sliding do wnward fully onto the Column. With assistance raise the Head Assemb ly and slide it fully[...]

Bolts of appropriate length, W ashers and Locknuts (not pro vided). T o Install/Reposition The Drive Belts: 1. The Drill Press features 12 speed selections from which to choose. 2. The two V -Belts (par ts #21C, 26C), when positioned on the three Pulle ys (parts #3C, 28C, 19C), will determine the speed at which the Drill Press will run. (See Assemb[...]

SKU 44836 P A GE 8 T o Obtain The Pr oper Cutting Speeds: 1. Factors which determine the best speed to use in the Drill Press are: A . The kind of material being dr illed. B . The siz e of the hole. C . The quality of cut desired. 2. Generally , in soft mater ial the speed should be higher than f or hard materials. The following guide indicates the[...]

T o Adjust The T ab le: 1. The T ab le (par t #9A) may be adjusted in 4 directions . 2. T o raise or lower the T ab le , release the T ab le Clamp (par t #11A), and tur n the Crank (par t #6A) clockwise to raise the T able and countercloc kwise to lower the T ab le . When the desired height of the T ab le has been reached, secure the T ab le in pla[...]

SKU 44836 P A GE 10 5. The Drill Press is now set to drill holes to your pre-determined depth, provided the surf ace of the workpiece is flat and le v el. Y ou ma y also dr ill a series of holes to the same depth. T o Operate The Drill Press: 1. Before starting the Drill Press, make sure all adjustments are properly made and all of the guards are i[...]

SKU 44836 P A GE 11 5. Set the depth of drill bit travel so that the drill bit cannot come into contact with the T ab le (par t #9A), or align the T ab le so that the hole in its center is in line with the drill bit. 6. The Drill Press is now ready to operate. CLEANING, INSPECTION, AND MAINTENANCE 1. Caution : Alwa ys disconnect the Dr ill Press fr[...]

SKU 44836 P A GE 12 FIGURE G[...]

SKU 44836 P A GE 13 PLEASE READ THE FOLLO WING CAREFULL Y THE MANUF A CTURER AND/OR DISTRIBUT OR HAS PR O VIDED THE P AR TS DIA- GRAM IN THIS MANU AL AS A REFERENCE T OOL ONL Y . NEITHER THE MANUF A C- TURER NOR DISTRIBUT OR MAKES ANY REPRESENT A TION OR W ARRANTY OF ANY KIND T O THE BUYER THA T HE OR SHE IS QU ALIFIED T O MAKE ANY RE- P AIRS T O T[...]

DESCRIPTION Head w/P ointer & T r im Motor Hex Nut M8 W asher 8 Cord - Motor Hex Nut M10 Lockwasher 10 Bracket - Motor Hex Head Screw M8 x 1.25-20 Support - Motor Bracket Roll Pin 6 x 16 Knob - Motor Adjusting Hex Screw Socket Set M8 x 1.25-8 Lock - Depth Screw Ring - Depth Stop w/Scale Knob Rod Hub - Pinion Pin - Stop Connector - Wire Lockwash[...]

SKU 44836 P A GE 15 ASSEMBL Y DIA GRAM B NOTE: Some parts are listed and shown for illustra- tion pur poses only , and are not available individually as replace- ment parts.[...]

P AR TS LIST/ASSEMBL Y DIA GRAM C SKU 44836 P A GE 16 NOTE: Some parts are listed and shown for illustration pur poses only , and are not av ailable individually as replacement parts. DESCRIPTION Knob Pan Head Screw M5 x 0.8-12 Pulley - Motor Screw - Hex Socket Set Guard - Pulley w/Labels Bearing - Ball 12mm Shaft - Spindle Chuck Key Chuck T ube Qu[...]