Harbor Freight Tools 91010 инструкция обслуживания

3 N 1 Leaf Blo w er V ac ASSEMBL Y AND OPERA TING INSTR UCTIONS 3491 Mission Oaks Blvd., Camarillo , CA 93011 Visit our W eb site at: http://www.harborfreight.com Cop yright 2003 by Harbor F reight T ools ® . All rights reser ved. No por tion of this manual or any ar twork contained herein may be reproduced in an y shape or form without the e xpre[...]

SKU 91010 Page 2 PR ODUCT SPECIFICA TIONS SA VE THIS MANU AL Y ou will need this manual for the saf ety warnings and precautions, assembly , operating, inspection, maintenance and cleaning procedures, parts list and as- sembl y diagram. Keep y our in voice with this manual. Write the in v oice number on the inside of the front co ver . Keep this ma[...]

SKU 91010 Page 3 ELECTRICAL SAFETY 4. Grounded tools must be plugged into an outlet properly installed and grounded in accordance with all codes and ordinances. Never remove the grounding pr ong or modify the plug in any wa y . Do not use any adapter plugs. Check with a qualified electrician if you are in doubt as to whether the outlet is properly [...]

SKU 91010 Page 4 12. A v oid accidental star ting. Be sure the P ower Switch is off before plug ging in. Carrying power tools with your finger on the Power Switch, or plugging in power tools with the Power Switch on, invites accidents. 13. Remove adjusting keys or wrenches before turning the power tool on. A wrench or a key that is left attached to[...]

SKU 91010 Page 5 SER VICE 22. T ool service must be perf ormed only b y qualified repair personnel. Ser vice or maintenance perf or med by unqualified personnel could result in a risk of injur y . 23. When servicing a tool, use only identical replacement parts. Follow instructions in the “Inspection, Maintenance, And Cleaning” section of this m[...]

SKU 91010 Page 6 10. W ARNING! Nev er operate this tool in the rain or w et conditions. Danger of electrical shock or electrocution exists in these conditions. 11. Never la y the V acuum Leaf Blower do wn until the motor has come to a complete stop. Allow the motor to come to a complete stop before releasing it, as an uncontrolled running tool may [...]

SKU 91010 Page 7 GROUNDING W ARNING! Improperly connecting the grounding wire can result in the risk of electric shock. Check with a qualfified electrician if you are in doubt as to whether the outlet is properly grounded. Do not modify the power cord plug provided with the tool. Never remove the grounding prong from the plug. Do not use the tool i[...]

SKU 91010 Page 8 FIGURE B DOUBLE INSULA TED T OOLS: T OOLS WITH TWO PR ONG PLUGS 4. T ools mar ked “Doub le Insulated” do not require grounding. They ha ve a special double insulation system which satisfies OSHA requirements and complies with the applicable standards of Underwriters Laboratories, Inc., the Canadian Standard Association, and the[...]

SKU 91010 Page 9 6. If you are using an extension cord outdoors, make sure it is marked with the suffix “W -A” (“W” in Canada) to indicate it is acceptable f or outdoor use. 7. Make sure your extension cord is properly wired and in good electrical condition. Always replace a damaged extension cord or have it repaired by a qualified electric[...]

SKU 91010 Page 10 ASSEMBL Y AND OPERA TING INSTR UCTIONS CAUTION: Always make sure the Power Cord is unplugged from its electrical outlet prior to assembling or making any adjustments to the tool. Attaching and remo ving the Blower T ube Assembly: (Please see assembly diagram on next page) 1. Inser t the guiding end of the Blower Extension into the[...]

SKU 91010 Page 11 Attaching and removing the Mulch Bag: 1. Position the Mulch Bag at the underside of the unit, with the pointed end of the bag toward the open end of the blower tube. Loop the opening in the Mulch Bag ov er the opening at the bottom of the Motor Housing. Tighten the cord on the bag around the edge of the opening on the Motor Housin[...]

SKU 91010 Page 12 T urning the unit ON and OFF , and Adjusting Blower Speed W ARNING! Do not tur n this unit on unless you are wearing safety glasses, and have taken precau- tions to be sure it is safe to do so. 1. T o tur n on unit, be sure it is plugged in. Then move ON/OFF Switch to the “|” position. T o tur n unit OFF , rotate s witch to ?[...]

SKU 91010 Page 13 THE MANUF ACTURER AND/OR DISTRIBUT OR HAS PRO VIDED THE P ARTS LIST AND ASSEMBL Y DIAGRAM IN THIS MANUAL AS A REFERENCE T OOL ONL Y . NEITHER THE MANUF A CTURER NOR DISTRIBUT OR MAKES ANY REPRESENT A T ION OR W ARRANTY OF ANY KIND T O THE BUYER THA T HE OR SHE IS QU ALIFIED TO MAKE ANY REP AIRS T O THE PRODUCT , OR THA T HE OR SHE[...]

SKU 91010 Page 14 ASSEMBL Y DIA GRAM NO TE: Some par ts are listed and shown f or illustration purposes only , and are not available individually as replacement parts. #30 and #31 listed on Parts List, not shown on Assembly Diagram. REV 11/04[...]