Harbor Freight Tools 95578 инструкция обслуживания

ASSEMBL Y AND OPERA TING INSTR UCTIONS 3491 Mission Oaks Blvd., Camarillo , CA 93011 Visit our W eb site at: http://www .harborfreight.com ® © T O PREVENT SERIOUS INJUR Y , READ AND UNDERST AND ALL W ARNINGS AND INSTR UCTIONS BEFORE USE. Due to continuing improvements, actual product may differ slightly from the product described herein. Model 95[...]

PR ODUCT SPECIFICA TIONS SA VE THIS MANU AL Y ou will need this manual for the saf ety warnings and precautions, assembl y , operating, inspection, maintenance and cleaning procedures, parts list and as- sembl y diagram. Keep y our in voice with this man ual. Write the in voice number on the inside of the front co ver . Keep this manual and in v oi[...]

ELECTRICAL SAFETY 4. Grounded tools must be plugged into an outlet properly installed and grounded in accordance with all codes and ordinances. Never remove the grounding pr ong or modify the plug in any wa y . Do not use an y adapter plugs. Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. If the[...]

in. Carr ying po wer tools with y our finger on the P o wer Switch, or plugging in power tools with the Power Switch on, invites accidents. 13. Remove adjusting ke ys or wrenches before turning the po wer tool on. A wrench or a key that is left attached to a rotating part of the power tool may result in personal injur y . 14. Do not overreach. Keep[...]

model. Accessor ies that ma y be suitab le f or one tool may become hazardous when used on another tool. SER VICE 24. T ool service must be perf ormed only by qualified repair per sonnel. Ser vice or maintenance perf or med b y unqualified personnel could result in a risk of injur y . 25. When servicing a tool, use only identical replacement parts.[...]

9. A v oid unintentional starting. Make sure y ou are prepared to begin wor k bef ore tur ning on the Angle Grinder . 10. Do not fo rce the Angle Grinder . This tool will do the work better and safer at the speed and capacity f or which it was designed. Do not f orce the rotating grinding wheel (not included) into the object being ground. Apply mod[...]

SKU 95578 For technical questions, please call 1-800-444-3353 P A G E 7 and other construction activities, contain chemicals known (to the State of Cali- f ornia) to cause cancer , bir th defects or other reproductiv e har m. Some e x- amples of these chemicals are: lead from lead-based paints, crystalline silica from bricks and cement or other mas[...]

to an electrically “liv e” terminal. (See Figure A.) 3. Y our tool m ust be plugged into an appropriate outlet, proper ly installed and grounded in accordance with all codes and ordinances . The plug and outlet should look like those in the f ollowing illustration. (See Figure A.) FIGURE A SKU 95578 For technical questions, please call 1-800-44[...]

EXTENSION CORDS 1. Grounded tools require a three wire extension cord. Double Insulated tools can use either a two or three wire extension cord. 2. As the distance from the supply outlet increases, you must use a heavier gauge extension cord. Using extension cords with inadequately sized wire causes a serious drop in voltage, resulting in loss of p[...]

SKU 95578 For technical questions, please call 1-800-444-3353 P A G E 1 0 SYMBOLOGY FIGURE D UNP A CKING When unpacking, chec k to make sure all the par ts shown on the P ar ts List on page 14 are included. If any par ts are missing or brok en, please call Harbor F reight T ools at the number shown on the cover of this manual as soon as possible. A[...]

install the conv e x (rounded outward) side of the Grinding Wheel toward the Spindle (7). (See Figure E.) 3. Screw the Outer Flange Nut (1) onto the Spindle (7). Depress and hold the Lock Pin (22) to keep the Spindle from turning. Then, use the provided Wrench (51) to firmly tighten the Outer Flange Nut onto the Spindle. (See Figure E.) SKU 95578 F[...]

SKU 95578 For technical questions, please call 1-800-444-3353 P A G E 1 2 FIGURE F 2. Grip the Angle Gr inder fir mly with both hands. Then tur n the P ower Switch (41) to its “ON” position to star t the Grinder . (See Figure G.) 3. Hold the Angle Grinder at an angle of 10 to 15 to the wor k surface . When only the outer edge of the grinding wh[...]

SKU 95578 For technical questions, please call 1-800-444-3353 P A G E 1 3 4. T o clean or replace the Carbon Brushes (38): It may become necessary to clean or replace the two Carbon Brushes when the Motor performance de- creases, or stops w orking completely . The Carbon Brushes are located on each side of the Motor Housing (40). T o do so , remo v[...]

SKU 95578 For technical questions, please call 1-800-444-3353 P A G E 1 4 P ARTS LIST AND ASSEMBL Y DIA GRAM Part # Description Part # Description P art # Description 1 Outer Fl ange Nut 18 Side Handle 35 Spring 2 Spri ng Washer 19 Screw 36 Wind Shield Ring 3 I nner Flange 20 Keeper 37 Brush Holder Cover 4 Wheel Guard 21 Lock Spring 38 Carbon Brush[...]

IMPORT ANT W ARRANTY INFORMA TION SKU 95578 For technical questions, please call 1-800-444-3353 P A G E 1 5 3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353 Harbor F reight T ools Co. makes ev ery effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser t[...]