Hayter Mowers 185E XR16 инструкция обслуживания

(English V ersion) P AR T NUMBER: 1 1 1-1519 (A) ISSUE 28.01.08 Hovertrim OWNER'S HANDBOOK MODELS : 184E XR44 Hovertrim 185E XR16 Hovertrim Manufactured by Hayter Limited 111-1519 (A) 28/1/08 4:44 pm Page 1.1[...]

111-1519 (A) 28/1/08 4:44 pm Page 1.2[...]

MAIN 1.3 5 6 12 3 13 7 9 8 15 11 2 4 14 1 HAY-G00108-A 10 16 Main Features Specifications FEA TURES Code 184E 185E Model XR44 XR16 Engine Honda Honda Engine type GXV57 GXV57 Fuel type Unleaded petrol Unleaded petrol Fuel capacity 0.271 litres 0.271 litres Engine Oil type SAE 13/30 SAE 13/30 Oil sump capacity 0.251 litres 0.251 litres Cutting width [...]

111-1519 (A) 28/1/08 4:44 pm Page 1.4[...]

1.3 Main Features / Specifications 1.5 Contents 1.6 Introduction 1.7 W arranty 1.8 - 1.1 1 Safety Precautions 1.8 - T raining 1.8 - 1.9 - Pr eparation 1.9 - 1.10 - Operation 1.10 - 1.1 1 - Maintenance and Storage 1.1 1 - Safety Symbols 1.1 1 - Decal Symbols 1.12 Assembling the Mower 1.12 - Delivery Checklist 1.12 - Assembling 1.13 Before Starting t[...]

1.6 INTRODUCTION Thank you for purchasing an Allen machine. The following pages are designed to help you gain safe and efficient service from your machine. IMPOR T ANT : This ‘Owners Handbook’ should be regarded as part of the mower as it gives essential information regarding mower safety , operation, maintenance and specifications. Read and un[...]

1.7 W ARRANTY LIMITED W ARRANTY Allen mower ’ s are manufactured by Hayter Limited. The manufacturer warrants to the original user/purchaser that this unit shall be free from defects in material and workmanship under normal use and service for a period of one year from the date of purchase. The manufacturers of the engine furnish their own warran[...]

1.8 SAFETY PRECAUTIONS This safety alert symbol indicates important safety messages. When you see this symbol be alert to the possibility of injury . Carefully read the following and inform others. Y our machine is perfectly safe if used corr ectly . Failure to observe the following precautions may r esult in serious injury . Before using the machi[...]

1.9 SAFETY - Always use fresh fuel. Stale fuel can block the carburettor and cause leakage. - Replace fuel tank and oil tank caps securely . A damaged cutter device or impeller or both must be replaced. Before use, always visually inspect the cutting mechanism to ensure that it is in good condition. Do not operate the machine with an out of balance[...]

1.10 Do not put hands or feet near or under rotating parts. Never pick up or carry the machine while the engine is running. Never touch the exhaust/exhaust guard or cooling fins when the engine is hot. Stop the engine and disconnect the spark plug lead: - Before clearing blockages. - Before cleaning/checking or working on the machine. - After strik[...]

1.11 SAFETY PRECAUTIONS If the fuel tank has to be drained, this should be done outdoors and when the engine is cool. W ear strong work gloves when removing and reassembling the cutting device. Always replace worn or faulty parts with genuine Allen parts. Maintenance & Storage Safety Symbols Safety Alert - Be aware to the possibility of injury [...]

Remove the machine from the packaging and check that the following items have been supplied correctly . If any items are missing contact, your local dealer . Main deck, lower and upper handlebars. 1. Handlebar bolt x 2 5. Spanner x 1* 9. Handwheel x 2* 2. Bush x 4 6. T ies x 2* 3. Nut x 2 7. T ies* 4. W asher x 4 8. U Bolt x 2* *Items 5 - 9 Not Ill[...]

T o prevent engine damage the engine is shipped without oil or petr ol. The engine must be filled with the corr ect grade of oil and petrol befor e starting. Always use high quality detergent oil classified SAE 10W -30. Never use additives with recommended oil. T o prolong the life of your engine it is important that the oil is changed after the fi[...]

Check that the engine stop lever moves freely and returns to it’ s rest position when released. 1. Open the fuel tank vent by turning the vent knob at least 2 or 3 turns counterclockwise. 2. T urn the fuel valve lever to the ON position. 3. T o start a cold engine, move the choke lever to the CLOSED position. T o restart a warm engine, leave the [...]

1.15 OPERA TING 4. Hold the handlebar together with the engine stop lever , place your foot on the deck and tilt the mower towards you. This will take the load off the engine making it easier to start. Pull the starter grip lightly until you feel resistance, then pull briskly . Return the starter grip gently . Do not allow the starter grip to snap [...]

The cutting height of your mower has been set at the highest position (1). If you prefer a lower cut follow these instructions: a. T urn the petrol tap to the off position and where fitted the vent screw . b. Disconnect the spark plug lead. c. T ilt the mower to its side. (Keeping the carburet -tor uppermost). d. Remove flexiblade from cutting disc[...]

T o prevent accidents stop the engine disconnect the spark plug lead before attempting to carry out maintenance pr ocedures on the mower . 1. Spark Plug / Lead 2. Exhaust Guard 3. Exhaust 4. Oil filler Cap/ Dipstick 5. Finger Guard 6. Start Grip 7. Fuel Cap V ent Knob 8. Fuel Cap 9. Choke Lever 10. Air Cleaner 1 1. Carburettor Should only be made b[...]

1.18 MOWER MAINTENANCE T o service the air cleaner remove the air cleaner cover (1) by releasing two top catches (2) and tilting away from body until lower tabs release. Remove cartridge (3) and clean by tapping gently on a flat surface. If very dirty or damaged replace. - Do not brush - Do not use petroleum solvents. - Do not oil the cartridge. Af[...]

Remove all grass and debris from the engine including the exhaust/exhaust guard, the air ways in the top cowl and the surround- ing deck areas on a daily basis after use. Never spray the engine with water during cleaning. W ater can contaminate the fuel. Always clean with a brush or compressed air . Grass and debris may clog the engine’ s air coo[...]

Storage Change the engine oil after the first 5 hours of operation and thereafter according to the ‘Maintenance Schedule’:- 1. Drain fuel by running the engine until the fuel tank is empty . 2. Remove the spark plug lead. 3. Allow the engine to cool. 4. Drain the oil while the engine is warm.(Not hot) 5. T ip the machine over on to its side ens[...]

EC DECLARATION OF CONFORMITY Ma nufac t ure r: HAYT ER LI MITED , Address: Spell brook, B ish op’s Stort ford, He rts. C M2 3 4BU. ENGLAND declare that the trimmer : Model name: Mod el No : Cutt ing widt h: Speed of rotati on of the cutti ng device: Engine Ma nufacture r: Speed of rotat ion of engine: XR44 CODE 184E 40 cm 4800 rpm Honda 4800 rpm [...]

1.22 TROUBLE SHOOTING PROBLEM POSSIBLE F AUL T REMEDY Engine will not turn over Engine stop lever released. Operate engine stop lever . Incorrect oil level. Check oil level. Obstruction under deck. Remove obstruction. Engine smokes Excess oil level. Check oil level. Air cleaner cartridge oil Service air cleaner . soaked or blocked. Engine runs then[...]

PROBLEM POSSIBLE F AUL T REMEDY Engine vibrates excessively Mounting bolts loose. T ighten bolts Cutter disc bolt loose. Tighten bolt Bent crankshaft. Consult your dealer Damaged impeller or cutter disc Consult your dealer Uneven cut Flexiblade out of balance Replace flexiblade Engine running slow Consult your dealer Impeller air vents blocked Chec[...]

1.24 Item No. Description Part No. Q ty Item Note 1 ALLEN XR44 DECAL 111-1516 1 2 ALLEN XR16 DECAL ONLY 111-1825 1 3 WASHER 1/4*7/8*.08" THK 09263 2 4 NUT M6 NYLOC 'T' TYPE 09438 3 5 CABLE TIE H Y3966 3 NOT SHOWN 6 BOLT M6*45 09568 1 7 SCREW PLASTITE DIA 5*22 PAN POZI 09765 3 8 SCREW SOC HD BUTTON M6*16 09784 4 9 DECAL - SAFETY PETRO[...]

1.25 1 2 4 6 9 10 11 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 38 40 41 12 4 7 27 39 37 3 36 36 37 8 MAINFRAME PA R T S LIST 111-1519 (A) 28/1/08 4:44 pm Page 1.25[...]

1.26 NOTES 111-1519 (A) 28/1/08 4:44 pm Page 1.26[...]

1.27 Serial No: Engine T ype:- GXV57 Engine:- Honda Engine T ype:- GXV57 Engine:- Honda Date of Sale:- Y our Local Dealer:- CUST OMER INFORMA TION 111-1519 (A) 28/1/08 4:44 pm Page 1.27[...]

Manufactured by Hayter Limited Hayter Limited Spellbrook, Bishop’ s Stortford, Herts, CM23 4BU, England. T el: +44 (0) 1279 723444 Fax: +44 (0) 1279 600338 e-mail: sales@hayter .co.uk www .hayter .co.uk YOUR HA YTER DEALER IS: 111-1519 (A) 28/1/08 4:44 pm Page 1.28[...]