Hearth and Home Technologies GRL-700-AU инструкция обслуживания

1 MODEL: GRL-700-AU AUSTRALIAN GAS ASSOCIA TION APPROVED Approval Number 5669 THIS MANUAL MUST BE USED FOR INST ALLA TION AND RET AINED BY HOMEOWNER FOR OPERA TION AND MAINTENANCE. HEA T -N-GLO, a brand of Hearth & Home T echnologies Inc. 20802 Kensington Boulevard, Lakeville, MN 55044, U.S.A. • (952) 985-6000 2010-900C 7/03 INST ALLA TION AN[...]

2 IMPORTANT: Read all instructions carefully before starting installation. Failure to follow these installation instructions may result in a possible fire hazard and will void the warranty. Save this Manual for future reference. Copyright 2003 Heat-N-Glo, a brand of Hearth & Home Technologies Inc. 20802 Kensington Boulevard, Lakeville, MN 55044[...]

3 Table of Contents 1.0 INTRODUCTION ......................................................................................................... 5 2.0 ASSEMBL Y ................................................................................................................. 5 GAS LINE CONNECTION .......................................................[...]

4 FIGURE 1 FIREPLACE OPENING Minimum Maximum WIDTH: 700mm 1050mm DEPTH: 300mm 460mm HEIGHT: 425mm 540mm DEPTH WIDTH TOP VIEW TOP VIEW - FIREPLACE AREA GRATE CONTROL ACCESS COVER PILOT ASSEMBLY BURNER ON/OFF SWITCH GAS VALVE FLEX TUBE PIEZO IGNITOR FRONT SUROUND REAR SURROUND 300mm DEPTH 33mm MINIMUM NOTE: Unit must be 33mm back from fireplace front[...]

5 ! ! ! ! ! CAUTION: DO NOT PLACE ARTICLES ON OR AGAINST THIS APPLIANCE. CAUTION: DO NOT USE OR STORE FLAMMABLE MA TERIALS NEAR THIS APPLIANCE. CAUTION: DO NOT SPRA Y AEROSOLS IN THE VI- CINITY OF THIS APPLIANCE WHILE IT IS IN OP- ERA TION. W ARNING: THIS UNIT IS NOT FOR USE WITH SOLID FUEL. SOLID FUELS SHALL NOT BE BURNED IN A FIREPLACE WHERE A DE[...]

6 Figure 2 OPTIONAL WALL SWITCH, THERMOSTAT OR REMOTE REMOTE SWITCH PIGTAIL OFF ON ON/OFF SWITCH THERMOPILE TP/TH TP TH GAS VALVE THERMOCOUPLE A. Inlet gas supply pressure for purposes of input ad- justment, shall be 6.0 inches w.c. (1.5kPa) for natu- ral gas and 11 inches w.c. (2.75kPa) for propane. Manifold (outlet) pressure should be 3.2 inches [...]

7 LOG PLACEMENT INSTRUCTIONS STEP 1: Attach grate to as- sembly by sliding hooks into open- ings on the front surround. STEP 2: Ensure that tabs on front and rear surrounds are bent as shown in Figure 1. Carefully remove logs from carton and place as shown. NOTE: Overhead view and front view of burner, decorative front and surround. Log Set Assembl[...]

Heat-n-Glo GRL-700/GRL-850 Glowing Embers (Mineral Wool) Placement Natural Gas • Place single layer of 10mm circular sized pieces next to burner ports, taking care not to place material on or between ports. • Do not use all of the ‘ember’ in the packet. One packet should last 5-6 applications. • Repeat application at the start of each sea[...]

Heat-n-Glo GRL-700/GRL-850 Glowing Embers (Mineral Wool) Placement LPG • Place single layer of 10mm circular sized pieces on top of burner ports. • Increase the quantity of the “glowing embers” on the right, centre and left hand side, as indicated, of the burner where there is a cluster of burner ports. • Do not use all of the ‘ember’[...]

8 STEP 3: LOG #1 (SRV506-701) Put log #1 behind the locating tab on the right rear corner and up against the locating tab in the center. STEP 4: LOG #2 (SRV2010-703) Place log #2 on the right front corner of the unit using its locating slots (on log bottom). STEP 5: LOG #3 (SRV506-717) Place log #3 against the left front corner of log #2 as shown. [...]

9 STEP 7: LOG #5 (SRV 550-714 ) Rest log #5 against log #3 and rest its right edge on log #1. STEP 8: LOG #6 (SRV 530-716 ) Place log #6 in the groove on top of log #2 with its front on log #1. STEP 6: LOG #4 (SRV591-703) Rest log #4 in between the locating tabs on the rear shelf and rest its front top 330mm from the left corner of the decorative f[...]

10 ! 3.0 OPERATING GUIDELINES AND MAINTENANCE INSTRUCTIONS Upon completing the gas line connection, a small amount of air will be in the lines. When first lighting the pilot light, it will take a few minutes for the lines to purge themselves of this air. Once the purging is com- plete, the pilot and burner will light and operate as indi- cated in t[...]

11 ! A. This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow these in- structions exactly. B. BEFORE LIGHTING smell all around the appli- ance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor. C. Use only your hand to push in or turn the gas contr[...]

12 1. "STOP!" Read the safety information on previous page. 2. Remove the control access cover. 3. Turn the valve control knob to the "OFF" position. To do this, you must turn the knob clockwise to the "Pilot" position, and then press in and continue turning clockwise to the "OFF" position. GAS CONTROL VALVE [...]

13 Part number list on following page. (NG , LP) Exploded Parts Diagram Service Parts GRL-700-AU Beginning M anufacturing Date: 4-2003 Ending M anufacturing Date: ________ 12 Log set assembly 15 16 18 13 17 14 2 1 4 5 3 6 7 9 10 8 11 8 u[...]

14 ITEM Description SERIAL # PART NUMBER 1 ON/OFF Rocker Switch 060-521A 2 Burner NG 2010-003 2 Burner LP 2010-005 3 Burner Orifice NG 526-801 3 Burner Orifice LP 526-800 4 Piezo Ignitor 418-513 5 Valve NG 060-524 5 Valve LP 060-526 6 Access Door 2010-216 7 Flex Gas Supply Line 303-301 8 Surround Left and Right 2010-201 9 Surround Front 2010-200 10[...]

15 LIMITED 10 YEAR WARRANTY HEAT-N-GLO, a brand of Hearth & Home Technologies Inc. In order to presumptively establish the dates to which your HEAT-N-GLO Limited Warranty runs, you must mail the completed warranty card to HEAT-N-GLO, a brand of Hearth & Home Technologies Inc., 20802 Kensington Boulevard, Lakeville, MN 55044, within 60 days [...]