Henny Penny MP-944 инструкция обслуживания

Henny Penny Mod el MP-941/942/943/944 Henny Penny Multipurpose Holding Cabinet Model MP-941 Model MP-942 Model MP-943 Model MP-944 OPERATOR’S MANUAL[...]

Model MP-941/942/943/944 LIMITED WARRANTY FOR HENNY PENNY EQUIPMENT Subject to the fol lowing con ditions, He nny Penny Co rporati on makes the following limited warranties to the original purchaser only for Henny Penny appliances and replacem ent parts: NEW EQUIPMENT: Any pa rt of a ne w appliance, e xcept ba skets, lam ps, and fuses, whi ch prove[...]

Model MP-941/942/943/944 TABLE OF CONTENTS Section Page Section 1. INTRODUCTION ....................................................................................................... ....1-1 1-1. Multipurpose Holding Cabinet ...............................................................................1-1 1-2. Features ...........................[...]

Model MP-941/942/943/944 SECTION 1. INTRODUCTION 1-1. MULTIPURPOSE The Henny Penny Multipurpose Holding Cabinet HOLDING CABINET is a basic unit of food equipment designed to hold hot foods at proper temper ature in commercial food operations. This cabinet will keep hot foods hum id while maintaining tem perature. As of August 16, 2005, the Waste El[...]

Model MP-941/942/943/944 1-5. SAFETY The only way to ensure safe operation of the Henny Penny Multipurpose Holding Cabinet is to fully understand the proper in stallation, operation and maintenance procedures. The in structions in this manual have been prepared to aid you in learning the proper procedures. Where information is of particular importa[...]

Model MP-941/942/943/944 SECTION 2. INSTALLATION 2-1. INTRODUCTION This section provides the installation instructions for the Henny Penny Multipurpose Holding Cabinet. Installation of this unit should be performed by a qualified service technician. Do not puncture the skin of unit with drills or screws as component damage or electrical shock could[...]

Model MP-941/942/943/944 2-2. UNPACKING (Continued) 4. Open drawers and remove the packing or literature that is inside. 5. Pull off any protective cove ring from the exterior of the cabinet. 6. Your multipurpose holding cabinet is now ready for location and setup. 2-3. ELECTRICAL The multipurpose holding cabinets are available f rom the factory as[...]

Model MP-941/942/943/944 2-4. CABINET DIMENSIONS MP-941 1 0 3 2 - 3[...]

Model MP-941/942/943/944 2-4. CABINET DIMENSIONS (Continued) 2-4 103[...]

Model MP-941/942/943/944 SECTION 3. OPERATION 3-1. INTRODUCTION This section provides oper ating procedures for the multipurpose holding cabinets. Read the Introduction, Installation and Operation Sec tions, and all instructions should be followed before operating the cabinet. This section contains an e xplanation of all controls, components, and i[...]

Model MP-941/942/943/944 3-2. OPERATING CONTROLS AND COMPONENTS (Continued) Figure 3-1 3-3. START-UP Before using the cabinet, it should be thoroughly cleaned as described in the cleaning procedures section of this manual. To put the cabinet into operation, move each POWER switch to the ON position and adjust each contro l to the appropriate temper[...]

Model MP-941/942/943/944 3-3. START-UP (Continued) 1. Turn the POWER switch to the ON position. 2. The display will show the time of day or “ON”. Press and hold the appropriate drawer button to view the actual temperature of the drawer. 3. Wh en the temperature LED illum inates, the setpoint temperature has been reached and product can now be l[...]

Model MP-941/942/943/944 3-5. CLEANING (Continued) 5. Clean the interior of the cabinet thoroughly with a cloth and soapy water. Do not use steel wool, other abrasive cleaners or cleaners/sanitizers con taining chlorine, bromine, iodine or ammonia chemicals, as these will deteriorate the stainle ss steel material and shorten the life of the unit. D[...]

Model MP-941/942/943/944 3-6. OPERATION AND 2. While holding in on the drawer button, press and PROGRAMMING release the SET button. Now the setpoint temperature (Continued) will be blinking at a faste r rate. Now release the drawer button. 3. Press the UP and DOWN buttons to change the setpoint temperature. 4. Once the desired setpoint temperature [...]

Model MP-941/942/943/944 3-6. OPERATION AND Setting Control to the Correct Number of Draw ers PROGRAMMING (Continued) The different models, MP-941, 942, 943, and 944, all use the same control board. The boards are programmed at the factory for the correct unit. But, should the unit show “E06” or some drawers will not heat, the board may not be [...]

Model MP-941/942/943/944 G L O S S A R Y HENNY PENNY HO LDING CABINETS air temperature probe a round devi ce located inside t he cabinet that measures t he inside air temperature an d sends that i nformation t o the contr ol panel concentration ring assembly a metal assembly located in the water pan in the bottom of the unit that h elps keep an eve[...]

Model MP-941/942/943/944 probe clip a metal holder that attaches to the outside of the contro l panel to hold the food probe when not in use; the clip is an optional accessory product load capacity the highest recommen ded number of pounds/k ilograms of food product that can be safely held in the cabinet proof function a program used for allowing b[...]

*FM05 - 017 - E * Henny Penny Corp., Eaton, Ohio 45320, Revised 02- 21 -0 8 Henny Penny Corporation P.O.Box 60 Eaton,OH 45320 1-937-456-8400 1-937-456-8402 Fax Toll free in USA 1-800-417-8417 1-800-417-8434 Fax www.hennype nny.com[...]