Henny Penny PFG-690 инструкция обслуживания

Henny Penny Pressure Fryer Model PFG-690 TECHNICAL MANUAL[...]

[...]

Model 690 810 FM06-006 Revised 8-12-10 This manual should be retained in a convenient location for future reference. A wiring diagram for this appliance is located on the rear shroud cover of the control panel. Post in a prominent location, instructions to be followed if user smells gas. This information should be obtained by consulting the local g[...]

Model 690 HENNY PENNY 8 HEAD GAS PRESSURE FR YER SPECIFICA TIONS Height 61” (155 cm) W idth 24” (61 cm) Depth 41¾” ( 106 cm) Floor Space Approximately 7 sq. ft. (0.65 sq. m.) Pot Capacity 8 Head of chicken (32 lbs.) (14.4 kg.) 130 lbs. shortening (59 kg.) Electrical 120 V AC, 1 Phase, 50/60 Hz, 10 Amp, 3 W ire Service 240 V AC, 1 Phase, 50/6[...]

Model 690 T ABLE OF CONTENTS Section Page Section 1. TROUBLESHOOTING .............................................................................................. 1-1 1-1. Introduction .................................................................................................... 1-1 1-2. Safety ...............................................[...]

Model 690 T ABLE OF CONTENTS (Continued) Section Page Section 2 MAINTENANCE (Continued) 230 V olt Ladder Diagram (AP0803002 & BELOW) ..................................... 2-37 230 V olt Ladder Diagram (AP0803003 & ABOVE) ...................................... 2-38 100-120 V olt F AST W iring Diagram (AP0803002 & BELOW) .................[...]

Model 690 1-1. INTRODUCTION This section provides troubleshooting information in the form of an easy-to-read table. If a problem occurs during the f rst operation of a new fryer , recheck the installation per the Installation section of the Operator ’ s Manual. Before troubleshooting, always recheck the operation pro- cedures per section 3 of the[...]

Model 690 1-3. TROUBLESHOOTING T o isolate a malfunction, proceed as follows: 1. Clearly def ne the problem (or symptom) and when it occurs. 2. Locate the problem in the T roubleshooting table. 3. Review all possible causes. Then, one at a time, work through the list of corrections until the problem is solved. 4. Refer to the maintenance procedures[...]

Model 690 Problem Cause Correction COOKING SECTION Product Color Not Correct: A. T oo Dark • T emperature too high • Check temperature setting in the program mode; see Programming section of Operator ’ s Manual • Faulty temperature probe • Remove and replace tempera- ture probe • Shortening too old • Change shortening • Shortening t[...]

Model 690 Problem Cause Correction COOKING SECTION (Continued) D. Spotted • Improper separation of the • Load product into basket Product product properly • Breading not uniform on • Sift breading regularly the product • Separate product during breading • Burned breading particles • Filter the shortening more on product frequently •[...]

Model 690 Problem Cause Correction COOKING SECTION (Continued) D. Rancid T aste • Shortening too old • Replace shortening and follow recommended care and use of shortening • Infrequent f ltering • Replace shortening and follow recommended care and use of shortening • Non-compatible products • Replace shortening cooked within the same ?[...]

Model 690 Problem Cause Corr ection POWER SECTION W ith switch in • Open circuit • Check to see that unit is POWER position, plugged in the fryer is com- • Check the breaker or fuse pletely inoperative at supply box (NO POWER) • Check voltage at wall receptacle • Check MAIN POWER switch; replace if defective • Check cord and plug PRESSU[...]

Model 690 Problem Cause Correction PRESSURE SECTION (Continued) Pressure does not • Not enough product in fryer • Place proper quantity of build or product not fresh fresh product within frypot to generate steam • Metal shipping spacer not • Remove shipping spacer; removed from deadweight see Unpacking section of Operator ’ s Manual • L[...]

Model 690 • Gas valve knob turned to the OFF • Make sure the gas valve knob is position turned to the ON position • Blown fuse or tripped • Reset breaker or replace fuse circuit breaker at supply box or control panel • Blown fuse in PC board • Replace glass fuse in board • Faulty Power/Pump switch • Check Power/Pump switch per maint[...]

Model 690 Problem Cause Correction HEA TING OF SHOR TENING SECTION (Continued) Heating of • Supply line too small - low • Increase supply line size; shortening too gas volume refer to installation slow instructions • Improper ventilation • Refer to installation system instructions • Observe burners • Check gas pressure • Clean dilutio[...]

Model 690 Pr oblem Cause Correction SHOR TENING FOAMING/DRAINING SECTION Foaming or boil- • W ater in shortening • At end of a cook cycle, ing over of drain shortening and clean shortening frypot; add fresh shortening • Condensation line stopped up • Remove and clean conden- sation line • Improper or bad • Use recommended shortening sho[...]

Model 690 806 1-1 1 1-4. ERROR CODES In the event of a control system failure, the digital display shows an error message. These messages are coded: “E-4”, “E-5”, “E-6”, “E-32”, “E-41” and “E-71”. A constant tone is heard when an error code is displayed, and to silence this tone, press any of the product buttons. DISPLA Y CA[...]

Model 690 1-4. ERROR CODES (Continued) CE Only - Along with error codes fr om preceding page, CE units have the following self-diagnostic error codes: DISPLA Y CAUSE P ANEL BOARD CORRECTION “E-10” High limit Allow unit to cool (15-20 minutes), reset the high limit by manually pushing up on red reset button; if high limit does not reset, high li[...]

Model 690 2-1. INTRODUCTION This section provides checkout and replacement procedures for various parts of the fryer . Before replacing any parts, refer to the T roubleshooting section to aid you in f nding the cause of the malfunction. 2-2. MAINTENANCE HINTS 1. A multimeter will help you check the electric components. 2. When the manual refers to [...]

Model 690 2-4. HIGH TEMPERA TURE LIMIT CONTROL This high temperature control is a safety , manual reset control, which senses the temperature of the shortening. If the shorten- ing temperature exceeds 425°F (218°C), this switch opens and shuts off the heat to the frypot. When the temperature of the shortening drops to a safe operation limit (15-2[...]

Model 690 2-4. HIGH TEMPERA TURE LIMIT CONTROL (Continued) Replacement T o avoid electrical shock or pr operty damage, move the power switch to OFF and disconnect main circuit breaker , or unplug cord at wall receptacle. 1. If the tube is broken or cracked, the control will open, shutting off electrical power . The control cannot be reset. 2. Drain[...]

Model 690 2-4. HIGH TEMPERA TURE 1 1. Pull all excess capillary line from the frypot and tighten nut LIMIT CONTROL into frypot wall. (Continued) Be sur e capillary bulb of high limit is positioned so it does not interfer e with the carrier or get damages when clean- ing the frypot. 12. W ith excess capillary line pulled out, tighten smaller nut. 13[...]

Model 690 2-5. POWER/PUMP SWITCH (Continued) Replacement 1. W ith control panel removed, and wires of f the switch, push in on tabs on the switch to remove from the panel. 2. Replace with new switch, and reconnect wires to switch following the wiring diagram. 3. Replace the control panel. 2-6. TEMPERA TURE PROBE T emperature Probe relays the actual[...]

Model 690 2-6. TEMPERA TURE PROBE 7. T ighten hand tight and then a half turn with wrench. REPLACEMENT (Continued) Excess force will damage temperature probe. 8. Connect new temperature probe to PC board and replace Control Panel. 9. Replace shortening. 10. T urn power ON and check out fryer . 2-7. COMPLETE CONTROL Should the Control Panel become i[...]

Model 690 2-8. PRESSURE REGULA TION The Henny Penny Fryer uses pressure as one of the compo- nents of the cooking process. Once the lid is sealed to the frypot and the solenoid valve closes, a deadweight valve maintains the correct pressure in the frypot. The lid has minimal and limited maintenance and repair proce- dures, which are addressed in th[...]

Model 690 2-10. REVERSING THE LID The gray rubber gasket surrounding the inside of the lid is GASKET designed to be reversed. Because of heat expansion and the pressure used for the cook ing process, the gasket is constantly under extreme stress. Reversing the lid gasket will help to ensure that the fryer will not lose pressure through leakage. 1. [...]

Model 690 The Lid Counterweight in the back of the fryer balances the weight of the lid system to allow easier opening and closing of the lid. The weight has two cables attached to it, and weighs about 150 lbs. (67.5 Kg). 1. Using a 3/8” socket, remove the nuts securing the rear shroud of the fryer and remove the shroud. 2. Using Phillip’ s-hea[...]

Model 690 2-12. PRESSURE P AD The pressure pads are plastic strips that the lid cam presses against to seal the lid. 1. Raise the lid. 2. Remove the four screws securing the lid cover and remove cover . 3. Push the lid cam back, off the pressure pads. 4. Using an Allen wrench, remove the large bolt securing pad. 5. Using a Phillips head screw drive[...]

Model 690 2-13. LID ADJUSTMENT If steam leaks out from around the lid gasket, the pressure pads could be worn or broken. If the pressure pad is worn, but not broken, it can be reversed 180 degrees, and the other end of the pad used. See Section 2-12. If steam leaks, check for: • Pressure pad wear • Cracked or worn gasket • Gasket installed im[...]

Model 690 2-15. SOLENOID V AL VE This is an electromechanical device that causes pressure to be held in the frypot. The solenoid valve closes at the beginning of the cook cycle and opens automatically at the end of the cook cycle. If this valve should become dirty , or the T ef on seat nicked, pressure will not build up. The gas fryer uses a 120 vo[...]

Model 690 2-15. SOLENOID V AL VE 5. If the core-disc assembly is sticking due to buildup of (Continued) shortening, breading, and food particles, proceed with the following steps: a. Unscrew the solenoid bonnet assembly from solenoid valve body . b. Remove the solenoid bonnet assembly and bonnet gasket. c. Remove the core-disc assembly , core sprin[...]

Model 690 2-15. SOLENOID V AL VE 13. W et O-ring around seat with water and insert O-ring (Continued) assembly (f at side f rst) in valve through “IN” side of body . Use an eraser end of pencil and press in the T ef on seal until it snaps into place. BE CAREFUL NOT TO MAR OR NICK THE SEA T . The smallest nick can cause a pressure leak. Replace [...]

Model 690 2-16. DEADWEIGHT V AL VE (Continued) DO NOT PULL THE RING ON SAFETY RELIEF V AL VE. HOT STEAM WILL BE RELEASED AND SEVERE BURNS WILL RESUL T . 1. A T THE END OF EACH DA Y’S USAGE OF THE FR YER, THE DEADWEIGHT V AL VE MUST BE ORIFICE CAP WEIGHT CLEANED. The fryer must be OFF and the pressure released. Open the lid and then remove the dea[...]

Model 690 2-17. REMOV AL & CLEANING 2. Use a wrench to loosen the valve from the pipe tee; turn OF SAFETY RELIEF V AL VE counterclockwise to remove. (Continued) 3. Clean the inside of the pipe tee with hot water . T urn the safety relief valve towards the rear of fryer when reinstalling safety relief valve. 4. Immerse the safety relief valve in[...]

Model 690 2-19. GAS CONTROL V AL VE The gas control valve sends regulated gas to burners when the controller calls for heat. The control valve can be turned on or off. In ON position, and power switch ON, a spark ignitor lights a standing pilot, and when the control calls for heat, the valve is opened and the burners are ignited. Safety Precautions[...]

Model 690 2-19. GAS CONTROL V AL VE (Continued) 4. Remove left side panel. 5. Remove control panel. 6. Unscrew nut from inlet line from the control valve. 7. Remove the bracket from behind the control valve. 8. Remove pilot light tube from control valve. 9. Loosen f ttings from tee and pull control valve assembly from the unit. 10. Remove the f tti[...]

Model 690 2-20. BLOWER ASSEMBL Y The blower motor circulates air into the burner area to create the correct heat for the fryer . If the blower fails, a sensor will shut the power control valve down. 1. Make sure unit is off, and close and lock the lid. Lid should be in locked down position. Failure to do so could result in personal injury . 2. Remo[...]

Model 690 2-21. TRANSFORMER The transformer reduces the voltage down to accommodate those components with low voltage. 1. Remove electrical power supplied to the unit. T o avoid electrical shock or pr operty damage, move the power switch to OFF and disconnect main circuit breaker , or unplug cord at wall receptacle. 2. Remove the control panel. 3. [...]

Model 690 2-22. AIRFLOW SWITCH The air f ow switch senses the f ow of air coming from the blower . If the airf ow is reduced below a set amount, the switch will cut power to the control valve, which shuts the burners down. Replacement 1. Remove electrical power supplied to the unit. T o avoid electrical shock or pr operty damage, move the power swi[...]

Model 690 2-23. DRAIN MICROSWITCH Upon pulling out on the drain handle, the microswitch should be activated and the unit will not heat, but when the handle is pushed back, the unit should operate properly . The bracket on the microswitch is slotted so it can be adjusted backward or `forward. 1. Remove electrical power supplied to the unit. T o avoi[...]

Model 690 2-24. DRAIN V AL VE The drain valve opens when drain valve handle is pulled out AND EXTENSION and drains the shortening out of the pot. 1. Using a 3/8” socket, remove the nuts securing the drain switch bracket, and pull the bracket from the studs. 2. Remove the nut securing the drain handle and pull the handle from the drain valve. 3. U[...]

Model 690 2-25. AIR V AL VE The air valve allows circulation of the shortening in the frypot to keep the shortening at a uniform temperature. 1. Remove electrical power supplied to the unit. T o avoid electrical shock or pr operty damage, move the power switch to OFF and disconnect main circuit breaker , or unplug cord at wall r eceptacle. 2. Remov[...]

Model 690 2-26. CLEANING THE Clean the dilution box annually to ensure the unit operates DILUTION BOX ef f ciently and with few failures. 1. Make sure unit is off, and close and lock the lid. Lid should be in locked down position. Failure to do so could result in personal injury . 2. Remove the back shroud of the fryer . 3. Clean dilution box with [...]

Model 690 2-28. IGNITION MODULES Sends 24 volts to the ignitors and gas control valve. LED Indication 3 different modules are in the f eld. The White Rogers and Fenwall modules have a red LED, and the Robertshaw modules have a green LED. These LEDs help to identify a failure. For White Rogers & Fenwall modules, when the control calls for heat, [...]

Model 690 2-29. IGNITOR ASSEMBL Y The 690 Model has electronic spark ignition that lights a standing pilot. Replacement 1. Remove electrical power supplied to the unit. T o avoid electrical shock or pr operty damage, move the power switch to OFF and disconnect main circuit breaker , or unplug cord at wall r eceptacle. TO A VOID INJUR Y , PROPER TY [...]

Model 690 2-30. FLAME SENSOR The f ame sensor should glow a bright red when pilot is lit and ASSEMBL Y allows the gas control valve to open. If it does not sense a f ame, it will shut the gas control valve down. Replacement 1. Remove electrical power supplied to the unit. T o avoid electrical shock or pr operty damage, move the power switch to OFF [...]

Model 690 1. Raise the lid and remove the retention ring from one end of the lid pin. 2. Slide the lid pin from unit. 3. Lift the lid from unit. The lid weighs 80 lbs (36 kg). T ake care when lifting lid to prevent personal injury . 4. Using a 3/8” socket, remove the nuts securing the rear shroud and remove shroud. 5. Using a Phillip’ s-head sc[...]

Model 690 2-30 507 2-32. NYLA TRON STRIPS REPLACEMENT (CONTD) 9. Lift the front shroud up and out, over the arm of the lid. 10. Thread the new nylatron strip through the track in the front shroud. 1 1. Lining up the holes in the strips, f t the front shroud back over the lid arms. 12. Secure the strips to the weight assembly . 13. Replace back shro[...]

Model 690 708 2-31 AP0803002 & below[...]

Model 690 AP0803003 & above 2-32 708[...]

Model 690 708 2-33 AP0803002 & below[...]

Model 690 AP0803003 & above 2-34 708[...]

Model 690 708 2-35 AP0803002 & below[...]

Model 690 AP0803003 & above 2-36 806[...]

Model 690 708 2-37 AP0803002 & below[...]

Model 690 AP0803003 & above 2-38 806[...]

Model 690 708 2-39 100-120 V olt F AST Wiring Diagram AP0803002 & below[...]

Model 690 AP0803003 & above 2-40 708[...]

Model 690 708 2-41 230 V olt F AST Wiring Diagram AP0803002 & below[...]

Model 690 AP0803003 & above 2-42 708[...]

Model 690 708 2-43 220-240 V olt F AST Wiring Diagram AP0803002 & below[...]

Model 690 AP0803003 & above 2-44 708[...]

Model 690 207 2-45 LIMITED W ARRANTY FOR HENNY PENNY EQUIPMENT Subject to the following conditions, Henny Penny Corporation makes the following limited warranties to the original pur - chaser only for Henny Penny appliances and replacement parts: NEW EQUIPMENT : Any part of a new appliance, except baskets, lamps, and fuses, which proves to be defec[...]

Model 690[...]

Model 690 106 3-1 SECTION 3. P AR TS INFORMA TION 3-1. INTRODUCTION This section lists the replaceable parts of the Henny Penny Model 690 Fryer . 3-2. GENUINE P ARTS Use only genuine Henny Penny parts in your fryer . Using a part of lesser quality or substitute design may result in damage to the unit or personal injury . 3-3. WHEN ORDERING P AR TS [...]

Model 690 FIGURE 3-0. FRAME & COVER ASSEMBL Y 3-2 1002[...]

Model 690 Figur e & Item No. Part No. Description Qty . 3-0 FRAME & COVER ASSEMBL Y 1 39796 WELDMENT – CONTROL P ANEL FRONT ........................... 1 2 53669 GUARD – POWER SWITCH ................................................... 1   3 29898 SWITCH – POWER .................................................................[...]

Model 690 Figur e & Item No. Part No. Description Qty . 3-1 CONTROL P ANEL   1 14418 KIT -CONTROL ASSY/AIR SWITCH MONIT OR.- SMS-DOM .... 1  1 14245 KIT -CONVERSION TO SMS-DOM ............................................... 1  1 14427 KIT -CONTROL -240V -NON-SMS T O SMS-DOM ........................ 1  1 14749 KIT -CON[...]

Model 690 Figure & Item No. Part No. Description Qty . 3-2 ELECTRICAL CONTROLS   1 60207 TRANSFORMER ASSY – 120V ................................................... 1   1 60536 TRANSFORMER ASSY – 24V/230V ........................................... 1 2 SC03-005 SCREW ........................................................[...]

Model 690 Figure & Item No. Part No. Description Qty . 3-3A FR YPOT COVERS & INSULA TION 1 52799 ASSY -INSUL/LFT . C/CHAMBER ................................................... 1 2 52041 INSULA TION-C/CHAMBER MOUNTIN ....................................... 4 3 52798 ASSY -INSUL/R T . C/CHAMBER ...............................................[...]

Model 690 Figur e & Item No. Part No. Description Qty . 3-3B INSULA TION COVERS 1 W A02-001 W ASHER – INSULA TION 1-1/2” DIA. ................................ 17 2 51763 INSULA TION COVER – LEFT ............................................. 1 3 51892 INSULA TION – C/CHAMBER SIDE ................................... 2 4 51765 INSULA TION [...]

Model 690 3-8 707 FIGURE 3-4. LID & COVER ASSEMBL Y[...]

Model 690 Figur e & Item No. Part No. Description Qty . 3-4 LID & COVER ASSEMBL Y 1 35792 LID INSTRUCTION LABEL ................................................ 1 2 35675 FILLER-LID ........................................................................... 2 3 35243 COVER-MAIN LID ...........................................................[...]

Model 690 3-10 810 FIGURE 3-5. DRAIN P AN & FIL TER ASSEMBL Y[...]

Model 690 Figur e & Item No. Part No. Description Qty . 3-5 DRAIN P AN & FIL TER ASSEMBL Y 1 52194 CRUMB CA TCHER (OPTIONAL) (REQUIRES ITEM 10) ....... 1 2* 03204 CRUMB CA TCHER BASKET W/HANDLE (OPTIONAL) ........ 1 (FITS INSIDE FR YPOT) 2* 21010 . “COLD ZONE” CRUMB CA TCHER BASKET ASSEMBL Y .. 1 2* 24429 . HANDLE - CRUMB BASKET .......[...]

Model 690 3-12 810 FIGURE 3-6. FIL TER PUMP ASSEMBL Y (BELOW SN: AP0401001)[...]

Model 690 Figure & Item No. Part No. Description Qty . 3-6 FIL TER PUMP ASSEMBL Y (BELOW SN: AP0401001) 1 18107 CONDUIT CONNECTOR 3/8 X 90 ................................................. 2 2 54484 BLOWER/PUMP – FLEXIBLE CONDUIT ..................................... 1   3 17476 PUMP SEAL KIT .........................................[...]

Model 690 FIGURE 3-7. FIL TER PUMP ASSEMBL Y (SN: AP0401001 & ABOVE) 3-14 905[...]

Model 690 Figure & Item No. Part No. Description Qty . 3-7 FIL TER PUMP ASSEMBL Y (SN: AP0401001 & ABOVE) 1 18107 CONDUIT CONNECTOR 3/8 X 90 ............................................. 2 2 54484 BLOWER/PUMP – FLEXIBLE CONDUIT ................................. 1   3 17476 PUMP SEAL KIT ...........................................[...]

Model 690 3-16 806 FIGURE 3-8. GAS BURNER ASSEMBL Y[...]

Model 690 Figur e & Item No. Part No. Description Qty . 3-8 GAS BURNER ASSEMBL Y 0* 56990-01 BURNER ASSY – NA TURAL ...................................................... 2 0* 56990-02 BURNER ASSY – LP .................................................................... 2 0* 56990-03 BURNER ASSY – NA TURAL CE .............................[...]

Model 690 3-18 1209 FIGURE 3-9. GAS PIPING & CONTROLS[...]

Model 690 Figur e & Item No. Part No. Description Qty . 3-9 GAS PIPING & CONTROLS 1 FP01-1 17 ELBOW ............................................................................................. 2 2 FP05-010 FITTING 3/8 TUBE T O 1/4 NP ........................................................ 2 3 65173 MANIFOLD TUBE – LEFT .................[...]

Model 690 Figur e & Item No. Part No. Description Qty . 3-10 BURNER TUBES 1 54480 BRACKET ASSY – HIGH LIMIT SENSING BULB ................... 3 2 62051 CLIP – SPREADER – HEA T TUBE ............................................. 6 3 53670 SP ACER – HIGH LIMIT ............................................................... 1   4 16[...]

Model 690 Figur e & Item No. Part No. Description Qty . 3-1 1 CARRIER & RACKS 1 62183 CARRIER ASSY ............................................................................ 1 2 44782 RACK HALF SIZE – 8 HEAD FR YER ........................................ 5 3 35308 WELMENT - RACK HANDLE ..................................................[...]

Model 690 Figur e & Item No. Part No. Description Qty . 3-12 V ACUUM SWITCH 1 60202 TUBE-V ACUUM SWITCH ................................................................ 1   2 14240 KIT - V ACUUM SWITCH - VERITCAL ........................................... 1   2 72514 V ACUUM SWITCH – VER TICAL (Included in 14240 Kit) ......[...]

Model 690 810 3-23 3-13. DEADWEIGHT & SOLENOID ASSEMBL Y (SN: AP082029 & ABOVE)[...]

Model 690 Figure & Item No. Part No. Description Qty . 3-13 DEADWEIGHT & SOLENOID ASSY (SN: AP082029 & ABOVE)   1 16910 PRESSURE GAUGE .......................................................... 1   2 59742 RELIEF V AL VE ASSY ....................................................... 1 3 FP01-127 ELBOW , STREET , ½ X ½,[...]

Model 690 810 3-25 Figure & Item No. Part No. Description Qty . 3-14A STEAM BOX & HOSE ASSY (SN: AP082029 & UP) 1 35686 TUBE, DW T O EXHAUST ST ACK SS ............................ 1 2 MS01-297 HOSE CLAMP , SS - .500 – 1.062 DID ............................. 4 3 70569 TUBE, EXHAUST CONNECT ......................................... 1 4 [...]

Model 690 3-26 810 FIGURE 3-14B. STEAM BOX & HOSE ASSEMBL Y SN: AP0802028 & BELOW[...]

Model 690 Figure & Item No. Part No. Description Qty . 3-14B STEAM BOX & HOSE ASSEMBL Y (SN: AP0802028 & BELOW) 1 56335 BRACKET – CONDENSA TE BOX ................................................... 1 2 21878 TUBING – STEAM EXHAUST ......................................................... 1 2 42508 TUBING – STEAM EXHAUST -UNITS BUI[...]

Model 690 3-28 708 FIGURE 3-15. FLUE ASSEMBL Y & BLOWER SN: AP0802028 & BELOW[...]

Model 690 Figur e & Item No. Part No. Description Qty . 3-15 FLUE ASSEMBL Y & BLOWER (SN: AP0802028 & BELOW) 1 55681 FLUE ASSY – WELDMENT ........................................................ 1 2 55783 BRACKET – FLUE RET AINING ................................................. 1 3 SC03-005 SCREW SD #8 X 1/2 PH PHD ...............[...]

Model 690 3-30 810 FIGURE 3-16. FLUE ASSEMBL Y & BLOWER SN: AP0802029 & ABOVE 6[...]

Model 690 Figur e & Item No. Part No. Description Qty . 3-16 FLUE ASSEMBL Y & BLOWER (SN: AP0802029 & ABOVE) 1 70582 FLUE ASSY – WELDMENT ........................................................ 1 2 SC02-041 #8-32 X 7/16 PH IND XTRNL TRX ............................................. 1 3 NS02-002 NUT KEPS 1/4-20 C .....................[...]

Model 690 3-32 905 FIGURE 3-17. SOLENOID V AL VE ASSEMBL Y[...]

Model 690 Figur e & Item No. Part No. Description Qty . 3-17 SOLENOID V AL VE ASSEMBL Y 1 17121 V AL VE, SOLENOID 120V , 60 Hz ................................................ 1 1 18721 V AL VE, SOLENOID 208-240V , 60 Hz ......................................... 1 1 18724 V AL VE, SOLENOID 208-240V , 50 Hz ......................................[...]

Model 690 3-34 1008 FIGURE 3-18. FR YPOT & DRAIN PIPING[...]

Model 690 Figur e & Item No. Part No. Description Qty . 3-18 FR YPOT & DRAIN PIPING   4 14330 PROBE ASSY – DOMESTIC ........................................................... 1   4 14266 KIT -CE PROBE CONNECT OR RETROFIT (probe not included) .. 1 (CE units built prior to NOV . 1, 1999) 5 16226 NIPPLE 1/2 X 3-1/2 .......[...]

Model 690 3-36 708 FIGURE 3-19. LIFT BEAM & SHROUDS SN: AP0802028 & BELOW[...]

Model 690 Figur e & Item No. Part No. Description Qty . 3-19 LIFT BEAM & SHROUDS (SN: AP0802028 & BELOW) 1 55678 ASSY – I-BEAM/LIFT FRAME ................................................... 1 2 51548 . LIFT I-BEAM ............................................................................. 1 3 55677 . LIFT FRAME ASSY – WELDMENT ...[...]

Model 690 3-38 708 FIGURE 3-20. COUNTERWEIGHT & PULLEY SYSTEM (SN: AP0802028 & BELOW)[...]

Model 690 Figur e & Item No. Part No. Description Qty . 3-20 COUNTER WEIGHT & PULLEY SYSTEM (SN: AP0802028 & BELOW) 2 51677 PULLEY PLA TE ............................................................................ 1 3 35962 BRACKET/WHEEL ASSY ........................................................... 2   4 35207 CABLE .......[...]

Model 690 3-40 708 Figure & Item No. Part No. Description Qty . 3-21 COUNTER WEIGHT SYSTEM (SN: AP0802029 & ABOVE) 1 35026 ARM, LID SUPPOR T ........................................................ 2   2 35207 CABLE ............................................................................... 2 3 NS01-025 NUT , HEX 5/16-18 SS ...[...]

Model 690 1004 3-41 Figure 3-22. F AST Ready Parts[...]

Model 690 Figure & Item No. Part No. Description Qty . 3-22 F AST READY P AR TS 1 66287 ASSY - 392/692 - 120V F AST HEADER .................. 1 1 66288 ASSY - 392/692 - 230V F AST HEADER - CE .......... 1 1 66385 ASSY - 392/692 - 220-240V F AST HEADER ........... 1 1 66241 STUD ASSY - 392/692 CONTROL PNL .................. 1 1 66296 STUD ASSY -[...]