Hitachi CP-X885 инструкция обслуживания

1 LCD Projector CP-X880/CP-X885 USER'S MANUAL USER'S MANUAL V ol.2 (Extended) Thank you for purchasing this projector. • The information in this manual is subject to change without notice. • The manufacturer assumes no responsibility for any errors that may appear in this manual • The reproduction, transmission or use of this docume[...]

MAIN Menu Item Description BRIGHT Adjust Brightness: Light Dark CONTRAST Adjust Contrast: Strong Weak ASPECT Select Aspect Ratio: At RGB Input or Hi-Vision 1125i(1035i/1080i)/750p of COMPONENT VIDEO Input: 4:3 16:9 At VIDEO Input, S-VIDEO Input or 525i/525p/625i of COMPONENT VIDEO Input: 4:3 16:9 SMALL • The SMALL picture may not be displayed cor[...]

PICTURE-1 Menu PICTURE-2 Menu With the PICTURE-1 menu, the five items shown in the Table below can be performed. Perform each operation in accordance with the instructions in the Table. With the PICTURE-2 menu, the five items shown in the Table below can be performed. Perform each operation in accordance with the instructions in the Table. Item Des[...]

MUL TIFUNCTIONAL SETTINGS (continued) INPUT Menu The three Input menu items listed in the table below can be manipulated. For RGB input, the reception signal’s horizontal and vertical frequency is displayed on the initial menu screen. Use the table below as a guide for operation. 4 Example : INPUT Menu (BNC) MENU : SELECT MAIN PICTURE-1 PICTURE-2[...]

5 AUTO Menu With the AUTO menu, the four items shown in the Table below can be performed. Please perform each operation in accordance with the instructions in the Table. Item Description ADJUST Auto Adjust (for RGB): Automatically adjusts H POSITION, V POSITION, H PHASE, and H SIZE. Use this function with the maximum window size. Auto Adjust (for V[...]

MUL TIFUNCTIONAL SETTINGS (continued) 6 SCREEN Menu With the SCREEN menu, the five items shown in the Table below can be performed. Please perform each operation in accordance with the instructions in the Table. SCREEN Menu Item Description BLANK Selection of BLANK Screen: MyScreen ORIGINAL .. . . .. The BLANK Screen may be voluntarily selected. Th[...]

7 OPTION Menu With the OPTION menu, the five items shown in the Table below can be performed. Please perform each operation in accordance with the instructions in the Table. WIRELESS Menu The WIRELESS menu is only enabled if the wireless function is enabled. Using the wireless function requires a Wireless & Network Module Terminal (sold separat[...]

Message Description CHANGE THE LAMP AFTER REPLACING LAMP, RESET THE LAMP TIMER. (Note 1) Lamp usage time is approaching 2,000 hours. (Note 2) Preparation of a new lamp, and an early lamp change, is recommended. After you have changed the lamp, please be sure to reset the lamp timer. CHANGE THE LAMP AFTER REPLACING LAMP, RESET THE LAMP TIMER. THE PO[...]

9 Regarding the Indicator Lamps Lighting and flashing of the POWER indicator, the LAMP indicator, and the TEMP indicator have the meanings as described in the Table below. Please respond in accordance with the instructions within the Table. POWER indicator LAMP indicator TEMP indicator Description The orange lamp is lighted Turned OFF (Not lighted)[...]

10 WHA T TO DO WHEN YOU THINK A MACHINE DEFECT HAS OCCURRED (continued) Phenomena That May Easily Be Mistaken for Machine Defects Before requesting repair, check in accordance with the following chart. If the situation cannot be corrected, then contact your dealer. Although bright spots or dark spots may appear on the screen, this is a unique chara[...]

Dimension Diagram Unit : mm 380 117 130 10 303 290 120 2 8 72 • This specifications are subject to change without notice. NOTE SPECIFICA TIONS 11 Item Specification Product name Liquid crystal projector Liquid crystal panel Panel size 2.5 cm (0.99 type) Drive system TFT active matrix Pixels 786,432 pixels (1024 horizontal x 768 vertical) Lens Zoo[...]

12 If a problem occurs with the equipment, first refer to the “ WHAT TO DO WHEN YOU THINK A MACHINE DEFECT HAS OCCURRED ” section and run through the suggested checks. If this does not resolve the problem contact your dealer or service company. They will tell you what warranty condition is applied. W ARRANTY AND AFTER-SER VICE 8[...]

1 TECHNICAL TECHNICAL SIGNAL CONNECTOR PIN ASSIGNMENT RGB IN [1]/[2] RGB OUT D-sub 15-pin Shrink Mini Din 4-pin S-VIDEO Mini Din 4-pin Pin No Signal 1 Color: 0.286Vp-p (NTSC, burst signal), 75 Ω terminator 0.3Vp-p (PAL/SECAM, burst signal), 75 Ω terminator 2 Brightness: 1.0Vp-p, 75 Ω terminator 3 Ground 4 Ground signal Terminal Specification [...]

2 Resolution H × × V fH (kHz) fV (Hz) Rating Signal mode Display mode CP-X880 CP-X885 720 × 400 37.9 85.0 VESA TEXT Zoom in Zoom in 640 × 480 31.5 59.9 VESA VGA (60Hz) Zoom in Zoom in 640 × 480 35.0 66.7 Mac13"mode Zoom in Zoom in 640 × 480 37.9 72.8 VESA VGA (72Hz) Zoom in Zoom in 640 × 480 37.5 75.0 VESA VGA (75Hz) Zoom in Zoom in 640[...]

3 The following signals are used for the initial settings. The signal timing of some computer models may be different. In such case, refer to adjust the V.POSIT and H.POSIT of the menu. Display interval c Back porch b Sync a Front porch d Display interval c Back porch b Sync a Front porch d Computer / Signal Horizontal signal timing (µs) a b c d T[...]

4 CONNECTION TO THE MOUSE CONTROL 1 2 3 4 1 2 3 4 + 5V — DATA + DATA GND + 5V — DATA + DATA GND 1 23 4 2 1 3 4 USB jack (B type) USB jack (A type) Projector USB cable Computer ADB Mouse 2 1 4 3 6 5 2 1 4 3 8 7 10 9 12 11 14 13 15 RTS GND +5V ADB GND +5V ( POWER ON ) D ATA 2 1 4 3 Mouse jack Mini DIN 4-pin Projector Computer CONTROL Terminal D-s[...]

5 (1) Turn off the projector and computer power supplies, and connect with the RS-232C adapter via the RS-232C cable. (2) Turn on the computer power supply and after the computer has started up, turn on the projector power supply. Control jack D-sub 15-pin shrink jack 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 RD TD GND SELO RTS 1 2 3 4 5 6 7 8 9 CD RD TD[...]

6 Requesting projector status (Get command) (1) Send the request code Header + Command data (‘02H’+‘00H’+ type (2 bytes) +‘00H’+‘00H’) from the computer to the projector. (2) The projector returns the response code ‘1DH’+ data (2 bytes) to the computer. Changing the projector settings (Set command) (1) Send the setting code Head[...]

7 Command data chart Names Operation type Header Command data CRC Action Type Setting code Blank Color Set Blue BE EF 03 06 00 CB D3 01 00 00 30 03 00 White BE EF 03 06 00 6B D0 01 00 00 30 05 00 Black BE EF 03 06 00 9B D0 01 00 00 30 06 00 MyScreen BE EF 03 06 00 FB CA 01 00 00 30 20 00 ORIGNAL BE EF 03 06 00 FB E2 01 00 00 30 40 00 Get BE EF 03 0[...]

8 Command data chart (continued) Names Operation type Header Command data CRC Action Type Setting code H.Position Reset Execute BE EF 03 06 00 IC D3 06 00 03 70 00 00 H.Size Reset Execute BE EF 03 06 00 68 D2 06 00 04 70 00 00 Color Balance R Reset Execute BE EF 03 06 00 94 D3 06 00 05 70 00 00 Color Balance B Reset Execute BE EF 03 06 00 D0 D3 06 [...]

9 Names Operation type Header Command data CRC Action Type Setting code Color Balance B Get BE EF 03 06 00 45 D2 02 00 06 20 00 00 Increment BE EF 03 06 00 23 D2 04 00 06 20 00 00 Decrement BE EF 03 06 00 F2 D3 05 00 06 20 00 00 Keystone_V Get BE EF 03 06 00 B9 D3 02 00 07 20 00 00 Increment BE EF 03 06 00 DF D3 04 00 07 20 00 00 Decrement BE EF 03[...]

10 Command data chart (continued) Names Operation type Header Command data CRC Action Type Setting code Sync on G Set off BE EF 03 06 00 CB D0 01 00 08 30 01 00 on BE EF 03 06 00 5B D1 01 00 08 30 00 00 Get BE EF 03 06 00 68 D1 02 00 08 30 00 00 PinP Size Set off BE EF 03 06 00 FE 22 01 00 00 23 00 00 Large BE EF 03 06 00 6E 23 01 00 00 23 01 00 Sm[...]

Printed in Japan *QR54481* Hitachi America, Ltd. Computer Division 2000 Sierra Point Parkway, MS760 Brisbane, CA 94005-1835 Tel: +1-800-225-1741 Fax: +1-650-244-7776 www.hitachi.com/lcd. Hitachi Canada, Ltd. 6740 Campobello Road, Mississauga, Ontario L5N2L8, Canada Tel: +1-905-821-4545 Fax: +1-905-821-1101 Hitachi Home Electronics (Europe), Ltd. Du[...]