Hobart HL661 инструкция обслуживания

701 S. RIDGE AVENUE TROY, OHIO 45374-0 001 937-332-3000 · WWW.HOBARTCORP.COM Models HL60 0, HL66 1 & H L662 M L - 134145 ML-134218 ML-134219 INSTR UCTION MANU AL FORM 34800 Rev. B ( MARCH 2003)     [...]

– 2 – LEGACY 60-QUART MIXER[...]

– 3 – TABLE OF CONTENTS GENERAL ............................................................................................................................................. 4 INSTALLATION .................................................................................................................................... 5 Unpacking ............[...]

– 4 – Installation, Operation and Care of Legacy TM 60-Quar t Mixers SA VE THESE INSTRUCTIONS GENERAL The Legacy 60-quart mixer series are heavy-duty mixers which feature a 2.7-horsepower motor, digital Smart TM Timer, a power bowl lift and a #12 attachment hub as standard equipment. The Legacy series is available in three models: • The HL600[...]

– 5 – INST ALLA TION UNPACKING Immediately after unpacking the mixer, check for possible shipping damage. If this machine is found to be damaged after unpacking, save the packaging material and contact the carrier within 15 days of delivery. LOCATION Prior to installation, test the electrical service to assure that it agrees with the specificat[...]

– 6 – ELECTRICAL CONNECTIONS WARNING : ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH THE APPLICABLE PORTION OF THE NATIONAL ELECTRICAL CODE AND/OR OTHER LOCAL ELECTRICAL CODES. WARNING : DISCONNECT THE ELECTRICAL POWER TO THE MACHINE AND FOLLOW LOCKOUT / TAGOUT PROCEDURES. A hole for 3 / 4 "-trade-size conduit is located at the top[...]

– 7 – OPERA TION WARNING : MOVING AGITATOR IN BOWL, KEEP HANDS, CLOTHING AND UTENSILS OUT WHILE IN OPERATION. DO NOT USE WITHOUT INTERLOCKED GUARD. The Legacy mixer is equipped with Smart TM Timer controls and a power bowl lift. Other operating parts (Fig. 2) and their functions are described throughout the Operation section. The Wire Cage must[...]

– 8 – CONTROLS Model HL600 (With Four Mix Speeds Plus Stir Speed) Model HL600 Mixer Speeds STIR (Slow) STIR speed is for incorporating ingredients at the start of each mixing process. SPEED 1 (Low) This speed is for heavy mixtures such as pizza dough, heavy batters and potatoes. SPEED 2 (Medium-low) This speed is for mixing cake batters, mashin[...]

– 9 – Model HL661 (With One Mix Speed Plus Meat Grind, Cheese Shred, Vegetable Slice Speeds) Model HL661 Mixer Speeds SPEED 1 This speed is for heavy mixtures such as pizza dough. MEAT GRIND This speed is for grinding meat. CHEESE SHRED This speed is for shredding cheese. VEGETABLE SLICE This speed is for slicing vegetables.[...]

– 10 – Model HL662 (With Two Mix Speeds Plus Meat Grind, Cheese Shred, Vegetable Slice Speeds) Model HL662 Mixer Speeds SPEED 1 (Slow) This speed is for heavy mixtures such as pizza dough. SPEED 2 (Low) This speed is for developing pizza dough. MEAT GRIND This speed is for grinding meat. CHEESE SHRED This speed is for shredding cheese. VEGETABL[...]

– 11 – BOWL PLACEMENT The bowl must be installed before the agitator is installed. To install the bowl, fully lower the bowl support. Position bowl so the alignment pins on the left side of the bowl support fit in the holes in the bowl. Swing the bowl into the locked position on bowl support. AGITATOR To install an agitator, the bowl must be on[...]

– 12 – PREPARE FOR MIXING 1 . Place the mixing bowl on the bowl support. 2 . Pour ingredients into the bowl. 3 . Swing the bowl back to the locked position. 4 . Place the agitator inside the bowl, then attach it to the agitator shaft (Fig. 4). 5 . Return the wire cage to front-center position. 6 . Push and hold the up arrow on the bowl switch u[...]

– 13 – Using the Count-Down Mode (Timed Mixing) 1 . Turn the SPEED dial to select a mix speed. a . If the count-up mode was used for the previous batch, the desired time needs to be entered. b . If the count-down mode was used for the previous batch, the previous time will be displayed. If a different time is needed, turn the TIME selector to t[...]

– 14 – UNLOADING 1 . Unlock the bowl and swing-out slightly. Press and hold the down arrow on the bowl switch to lower the bowl. 2 . Open the wire cage assembly. 3 . Remove the agitator from the agitator shaft. 4 . Remove the bowl from the bowl support. WIRE CAGE (Fig. 5) The wire cage can be rotated out of the way to add ingredients or to acce[...]

– 15 – Remove and Clean Wire Cage (Fig. 6) 1 . Lower the bowl. Remove the agitator and bowl. 2 . While holding the wire cage securely with both hands, rotate it to your left until the front-center retainer shoe reaches the gap in the circular ridge of the planetary drip cup. 3 . Lower the front of the wire cage and move the wire cage slightly t[...]

– 16 – CLEANING WARNING : DISCONNECT THE ELECTRICAL POWER TO THE MACHINE AND FOLLOW LOCKOUT / TAGOUT PROCEDURES. New mixer bowls and accessories (beaters, whips and dough arms) should be thoroughly washed with hot water and a mild soap solution, rinsed with either a mild soda or vinegar solution and thoroughly rinsed with clear water before bei[...]

– 17 – MAINTENANCE WARNING : DISCONNECT THE ELECTRICAL POWER TO THE MACHINE AND FOLLOW LOCKOUT / TAGOUT PROCEDURES. LUBRICATION Fig. 7 Slideway The slideways (Fig. 7) should be lubricated approximately twice a year. To reach these areas, fully lower the bowl support and remove the apron, which is secured by thumb screws. Wipe a thin coat of Lub[...]

– 18 – Transmission To check the oil level, remove the top cover, which is secured by two screws. Remove the Transmission Fill Plug (Fig. 8) and check the oil level. If the oil level is below the line on the oil dipstick, add a small amount of the recommended transmission oil until it returns to the proper level. Do not overfill the transmissio[...]

– 19 – Measure Clearance Pour enough flour in the bowl to cover the bottom of the bowl where the beater travels. With the bowl fully raised (beater should not touch the bottom of the bowl), briefly run the mixer at the lowest speed. Turn off the mixer, disconnect the electrical power supply, and measure the depth of flour where the beater has t[...]

– 20 – TR OUBLESHOO TING Symptoms Possible Causes Mixer will not start. Circuit protector is in open position - check fuse or disconnect switch. Mixer is overloaded. Wire cage is not in the closed position. Bowl is not in closed (locked) position. Agitator touches bowl. Bowl is not in closed (locked) position. Improper agitator clearance - see [...]