Honda Automobiles H1000 инструкция обслуживания

!I[...]

[...]

a 0 The information in this operator’s manual is limited in application to Honda mulching kits for Honda 1000 and H3000 Series riding mowers. Before installing or operating this equipment, read this manual nd the owner’s manual supplied with the Honda riding mower. All information in this publication is based on the latest H3000 Series product [...]

[...]

1. DEALER INSTALLATION INSTRUCTIONS The installation of this kit must be performed by an authorized Honda riding mower dealer. These instructions are provided for dealer use. FOLLOW THESE INSTRUCTIONS CAREFULLY. Proper installation of this kit is essential for safe, reliable operation. Poor operation is a major cause of customer dissatisfaction. Yo[...]

1. DEALER INSTALLATION INSTRUCTIONS MULCHING KIT CONTENTS Mulching Blade Swirl Guide A Swirl Guide B Cover Plate 6x40mm Flange Bolts (2) 6x55mm Flange Bolt (1) 8x35mm Flange Bolts (2) 6 mm Flat Washers (6) 8 mm Flat Washers (4) 6 mm Lock Nuts (3) 8 mm Lock Nuts (4) MULCHING KIT INSTALLATION The mower deck must be removed from the riding mower to in[...]

1. DEALER INSTALLATION INSTRUCTIONS 3. Temporarily install the cover plate on the mower deck, using two 8 mm lock nuts. A- COVER PLATE 4. Hold swirl guide B against the cover plate. Insert a pencil through the holes in swirl guide B to mark drilling points on the cover plate. Remove the cover plate from the mower deck. Center punch and drill the co[...]

1. DEALER INSTALLATION INSTRUCTIONS 7. Install a 6 x 40 mm flange bolt, 6 mm washers, and a 6 mm lock nut in the first hole, as shown. Tighten the 6 mm nut and bolt to a torque value of 7.2 ft - lb (1 .O kg - m). To assure a good fit, mower deck holes must be drilled in sequence, and swirl guide A must be secured with nuts and bolts before drilling[...]

1. DEALER INSTALLATION INSTRUCTIONS 12. Install the mulching blade, using the original blade holder and hardware. Be sure the blade is positioned right side up (outer edges turn toward the mower deck). If the blade is installed upside down, it cannot cut properly. The blade bolts are specially designed for this application and must not be replaced [...]

2. SAFETY SAFETY LABEL LOCATIONS (H3000 SERIES) Read all safety instructions before operating the riding mower. w AVOID BURNS I / I PREVENT BRAKE FAILURE I DISENGAGE PARKING BRAKE WHEN BUZZER SOUNDS CONTINUOUSLY A DELAYED ENGINE CUTOFF WILL STOP THE ENGINE IF PARKING BRAKE IS NOT RELEASED. OPERATOR ONLY. NO PASSENGERS OPERATION ON PUBLIC STREETS OR[...]

2. SAFETY SAFETY LABEL LOCATIONS (H1000 SERIES) Read all safety instructions before operating the riding mower. rn Improperly driving on slopes or uneven terrain can cause the mower to tip over and u can be seriously hurt or killed. Read 'Sar Mowing Practices in the Owner's Manual carefully. w Objects hidden in the lawn can be thrown by t[...]

3. MOWING AND MULCHING RECOMMENDATIONS GRASS CUlTlNG BASICS Cutting Height A cutting height setting of 1 - 1/2 or 2 inches is appropriate for most lawns during cool weather. A higher cut may be needed to protect the lawn during hot summer months. Consult a local nursery or lawn and garden center for advice about specific types of grasses and growin[...]

3. MOWING AND MULCHING MULCHING Mulching cuts grass clippings and fallen leaves into fine particles that fall through the turf and decompose quickly. This returns nutrients to the soil and reduces'the need for raking, bagging, and disposal. For best mulching results, mow the lawn frequently, cutting off less than one inch of grass each time. I[...]

3. MOWING AND MULCHING RECOMMENDATIONS SIDE - DISCHARGE MOWING Side - discharge mowing should be considered where grass has grown too tall to mulch easily. Side - discharge mowing will leave grass clippings on top of the mowed areas and may need to be removed by raking. Heavy clumps of clippings should always be removed; grass must remain uncovered[...]

3. MOWING AND MULCHING ~~ ~ BAGGING Bagging should be considered for areas where you want the lawn to be clear of loose particles, such as around swimming pools, and for less frequently mowed areas, where grass has grown too tall to mulch easily. For bagging, you must remove the mower deck cover plate and swirl guide B, then install the bagging kit[...]

1 3. MOWING AND MULCHING RECOMMENDATIONS 5. Install the bag support assembly on the left and right struts, while inserting the center strut pin in the the hitch plate hole. 6. Grasp the upper chute by the chute handle. Raise the upper and middle chutes, then slide the middle chute over the lower chute. 7. Install the grass bags, and secure the hopp[...]

4. PARTS LIST MULCHING KIT: Part Number 06764 - 763 - ROO 8 mm MULCHING BLADE LOCK NUT (4) 72511 - 763 - RW SWIRL GUIDE A 901 15-659-003 8 mm FLAT COVER PLATE 76264 - 763 - MOO SWIRL GUIDE B 76268-763-RW 901 02 - 763 - RW H3000 Series Model Shown 13[...]

5. WARRANTY SERVICE OWNER SATISFACTION Your satisfaction and good will are important to your dealer and to us. All Honda warranty details are explained in the Distributor’s Limited Warranty. Normally any problems concerning the product will be handled by your dealer’s service department. If you have a warranty problem that has not been handled [...]

[...]

t.-[...]