Honeywell 50ZST инструкция обслуживания

E1 P/N 51889:E1 ECN 10-278 Document 51889 6/8/2010 Rev: V oice Evacuation Control P anels A UDIO•COMMAND•CENTER•25/50 A UDIO•COMMAND•CENTER•25/50ZS A UDIO•COMMAND•CENTER•25/50ZST Instruction Manual[...]

2 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 Fire Alarm System Limit ations While a fire alarm system may lower insurance rates, it is not a substitute for fire insurance! An automatic fire alarm system —typically made up of smoke detectors, h eat detectors, manual pu ll stations, audible warning devices, and a fire alarm contro[...]

Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 3 Inst allation Precautions Adherence to the followin g will aid in problem- free installation with long-term reliability: W ARNING - Several different sources of power can be connected to the fire alarm control p anel. Disconnect a ll sources of power bef ore servicing. Control unit and [...]

4 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 Sof tware Download s In order to supply the latest features and functionality in fire alarm and life safety techno logy to our cust omers, we make frequent upgrades to the embedded software in our products. T o ensure that you are install ing and programmi ng the latest features, we str[...]

Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 5 T able of Content s Section 1: Product Description ..................................................... ........................................ 13 1.1: Product Features ............ ......................... .......................... ......................... .................. .....[...]

Table of Contents 6 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 3.8.4: ACC-EPM External Page Module ................... ...................... .......................... ...................... ............60 Section 4: Operating Instructions ............................................................................ ............. [...]

Table of Contents Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 7 General Page Using the Optional RPJ-F Remote Ke yswitch via the Optional Fire Fighter Telephone Module .............. .............. .......................... ...................... ............... ......................... ..... .................... ..... 75 Emergenc[...]

Table of Contents 8 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 ACM-8RF Programming ...................... .............. ......................... ......................... ...................... .... ....1 21 MS-5210UD Programming ......... ......................... .......................... ......................... ...........[...]

Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 9 This control panel has been designed to comply with standards set forth by the following regu latory agencies: • Underwriters Laboratories Standard UL 864 • NFP A 72 National Fire Alarm Code NFP A S tandards This Fire Alarm Control Panel comp lies with the following NFP A Standards:[...]

10 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 Audio Riser 25W Speaker Circuit 25W Speaker Circuit Master Command Bus FACP Control ACC-25/50 FACP Control Master Command Bus Audio Riser To Additional ACC-25/50DA Panels 25W Spea ker Circuit 25W Speaker Circuit 25W Speaker Circuit 25W Speaker Circuit ACC-25/50DA ACC-25/50DA ACC-25/50 [...]

Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 11 Audio Command Center Zone System Up to 24 Zones @ 150W (max.) Speaker Circuit #16 1. The F ACP controls the audio system via the ACS Link or CMD inputs on the ACC-25/5 0ZS 2. The Audio Riser connects the audi o output of the ACC-25/50ZS to each of the ACC-25/50DAZS(s) to distribute ala[...]

12 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 Speaker Circuit #16 1. The F ACP controls the audio system via the ACS Link or CMD inputs on the ACC-25/50ZST . 2. The Audio Riser connects the audio output of the ACC-25/50ZST to each of the ACC-25/50DAZS(s) to di stribute alarm or paging audio. 3. The ACC-25/50ZST uses the Control Se[...]

Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 13 Section 1: Product Description The ACC-25/50 Series consists of the AUDIO•COM MAND•CENTER•25/50 (ACC-25/5 0), the AUDIO•COMMAND•CENTER•25/50 Zo ne Syst em (ACC-25/50ZS), and the AUDIO•COM- MAND•CENTER•25/50 Zone Sy stem with T elephone (ACC-25/50ZST) which are si ngle[...]

14 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 Product Description Product Features Primary applications for the aud io panels include st ructures such as restaurants, schools, auditori- ums, places of worship, buildings with occupancies over 50 , etc. The ACC-25/50 Series is designed to interface directly to addressable or convent[...]

Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 15 Product Features Product Description • T wo Form-C trouble relays:  System T rouble Relay - TB1  AC Power Loss Relay - TB7 • 35 mA Special Applica tion (auxiliary power ) output for addressable modules when interfaced with the Fire•Lite MS-9200(E) or MS-9600 F ACP or equiva[...]

16 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 Product Description Product Features AU X PO WER CMD1 CMD2 CMD3 CMD4 CMD5 MASTER CMD OUT AC L O S S TB4 TB2 TB5 TB8 TB9 TB10 TB6 TB7 P1 TB1 NC NO C C NO NC 1 2 1 2 3 1 2 3 4 1 2 3 4 1 2 3 4 Form-C AC Loss Relay nonsupervised Programmable Output Trigger - (supervised, power- limited) ac[...]

Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 17 Product Features Product Description ! CAUTION: OBSERVE PROPER POLARITY MATCH PROPER POLARITY CONNECTIONS TO FIELD WIRING AND SPEAKERS. POLARITY SHOWN IS IN THE STAND BY AND ALARM CONDITIONS. J1 T1 TB1 TB2 P1 SW1 BACK-UP ON CKT TBL AMP SUPV J1 TB1 TB2 P1 SW1 BACK-UP ON CKT TBL AMP SUPV[...]

18 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 Product Description Product Features ACC-25/50ZS Modules TB1 TB2 P1 SW1 BACK-UP ON CKT TBL AMP SUPV J1 TB1 TB2 P1 SW1 BACK-UP ON CKT TBL AMP SUPV J1 TB1 J1 1 2 3 4 5 6 7 8 ON S1 ON S3 0 5 4 3 2 1 9 8 7 6 0 5 4 3 2 1 9 8 7 6 S2 TENS ONES AAM 1 & 2 AAM1 JP1 TB1 TB9 TB4 SW2 SW1 TB5 TB[...]

Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 19 Specifications Product Description ACC-25/50ZST with ACC-FFT Module 1.2 Specifications AC Power - TB3 ACC-25/50, ACC-25/50ZS, ACC-25/50ZST : 120 V AC, 60 Hz, 1.5 amp. W ire size: minim um #14 A WGb with 600 V insulation. AC Loss Relay - TB7 Operation: normally energized fail-safe relay[...]

20 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 Product Description Specifications Battery (lead acid only) - P10 Maximum Charging Circuit: Normal Flat C harge - 27.6V @ 0.800 amp Maximum Charger Capacity: 18 Amp Hour battery . (Audio Comm and Center Series cabinet hol ds max. 18 Amp Hour Battery . Command Input Circuits (alarm pola[...]

Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 21 Specifications Product Description ACC-ZSM Zone Splitter Module and ACC-Z P MK Zone Page Module ( ACC-25/50ZS/T Only ) Power-limited circuitry Operation: Circuits on A CC-ZSM can be w ired as eight Style Y or fo ur Style Z Normal Operating V oltage fo r Speak er Circuits: 2 5 V RMS @ 1[...]

22 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 Product Description Specifications  End-of-Line Resistor required for Clas s B using T erminals 1(+) & 4(-): 4.7 K  , ½ watt (P/N: 27072)  Class A (no End-of-Line Resistor) requires the wiring of T erminal 1(+) to 2(+) and T erminal 3(-) to 4(-) Up to 25 Distributed Audio[...]

Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 23 Controls and Indicators Product Description 1.3 Controls and Indicators 1.3.1 Single Zone Operation (ACC-25/50, ACC-25/50ZS, ACC- 25/50ZST) Figure 1.5 depicts Single Zone operation with the maximum capacity of five messages. Single Zone may be configured for t wo to five message contro[...]

24 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 Product Description Controls and Indicators 1.3.3 RECORD/PLA YBACK  for recording messages when Record/Bypass switch is in the up Record positio n (refer to Section “S2 - Record Bypass Switch on AC C-25/50 Series Mother board (ACC-MCB)” on page 38, Section 2.1, ”S1 DIP Switch [...]

Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 25 Controls and Indicators Product Description • ACC Communication (green = active, extinguished = no communication) This (top right LED) indicat es communication betw een the ACC-ZPMK and the ACC- 25/50ZS/T main circuit boar d via the connectin g ribbon cable. • Speaker Circuit Zones[...]

26 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 Product Description Circuits • Amplifier Supervi sion (green) - Ampli fier module 1.4 Circuit s Input Circuits - CMD1, CMD2, CMD3, CMD4 & CMD5 • Input circuits CMD1 and CMD2 are independ ently field programmabl e to accept Notification Appliance Circuits o r normally open conta[...]

Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 27 Components Product Description • One Form-C AC Loss Relay . Contacts are rated 2.0 amps @ 30 VDC (resistive) and 0.6 amps 30 V AC (resistive). FC-MIM Microphone Interface Module or ACC-FFT Fire Fighter Telep hone Module • Connector P5 provides a connection for th e optional FC-MIM [...]

28 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 Product Description Components ACC-FFT Fire Fighter T elephone Module (refer to Figure 1.4 on page 19). Option al modules can be plugged in and mounted to the main ci rcuit board. The main circuit board is delivered pre- mounted in the cabinet. Audio Amplifier Module [ACC- AAM25] A sin[...]

Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 29 Optional Modules Product Description Dress Panel The Dress Panel is supplied standard with the system. It mounts to the cabinet with two supplied screws. The Dress Panel protects the user from high voltages and circuit boards from accidental damage. All system LEDs are visible with the[...]

30 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 Product Description Getting Started An ACC-25/5 0ZST does not requi re an FC-MIM sin ce the function of this module is incorpo rated in the ACC-FFT Fire Fighter T elephone module which is included with the ACC-2 5/50ZST . The Remote Microphone Module is con nected directly to the ACC-F[...]

Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 31 Getting Started Product Description • Record any new voice messages as described in Section 4, ”Operating Instructions” on page 63. • Program the F ACP to operate with the ACC-25/50ZS /T  Enable the ACS serial link or ANN-BUS serial link.  Assign audio zones where appl ic[...]

32 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 Section 2: Field Programming The AUDIO•COMMAND•CENTER•25/50, AU DIO•COMMAND•CENTER•25/50ZS, and AUDIO•COMMAND•CEN TER•25/50ZST can be field programm ed using option DIP switches S1, S3 and S5 located in the upper right side of t he main circuit board. It is recommende[...]

Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 33 Field Programming The following tables list the ACC-25/50 Series progr ammable features and the DIP switch settings required to select a parrticular feature. A detailed desc ription of each feature is presented in the fol- lowing pages. Figure 2.2 Field Programming DIP Switch for ACC-2[...]

34 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 Field Programming S5 DIP Switch ON OFF 1 not used 2 not used 3 Enable Background Music 1, 2 Disable Background Musi c (factory default) 4 not used 5 Command Input 1 Activation on Contact Closure Command Input 1 Activation on NAC polarity reversal (factory default) 3 6 Command Input 2 A[...]

Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 35 Field Programming 5 4 OFF and 5 OFF = No AC Loss Delay 4 OFF and 5 ON = 6 Hour Delay 4 ON and 5 OFF = 2 Hour Delay 4 ON and 5 ON = not used (Invalid Setting ) 6 Enable All-Call during Remote Mic. Page 8 Disable All-Call during Remote Mic. Page 8 - factory default 7 Enable ACC-25/50ZST [...]

36 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 Field Programming S1 DIP Switch Settings on ACC-25/ 50 Series Motherboard (ACC-MCB) 2.1 S1 DIP Switch Settings on ACC-25/50 Series Motherboard (ACC-MCB) • Switch 1 - T emporal pattern generated per ANSI S3.41 when Switch 1 is ON and Switches 2 and 3 are OFF OFF = No temporal pattern [...]

Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 37 S5 DIP Switch Settings on ACC-25/ 50 Series Motherboard (ACC-MCB) Field Programming 2.2 S5 DIP Switch Settings on ACC-25/50 Series Motherboard (ACC-MCB) • Switc h 1 - not used • Switc h 2 - not used • Switch 3 - contro ls whether backgroun d music can be played over the speakers [...]

38 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 Field Programming S2 - Record Bypass Switch on ACC- 25/50 Series Motherboard (ACC-MCB) • Switch 4 - used i n conjunction wit h Switch 5 to select AC Loss Delay time. • Switch 5 - used i n conjunction wit h Switch 4 to select AC Loss Delay time: 4 OFF and 5 OFF = No AC Loss Delay - [...]

Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 39 S4 - Battery Charger Switch on ACC-25/50 Series Motherboard Field Programming 2.5 S4 - Battery Charger Switch on ACC-25/50 Series Motherboard This switch controls whether the ACC-25 /50 Series wi ll charge the system batteries or if an exter- nal battery charger will be used. Right Pos[...]

40 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 Field Programming ACC-ZPMK Zone Page Module (ACC-25/50ZS & ACC-25/50ZST) 2.8.1 S1 DIP Switch Settings on ACC-ZPMK • Switches 1, 2 and 3 are used to configure the ACC-25 /50ZS/T for operation with a specific F ACP as shown in the following table: • Switch 4 - no t used (future) [...]

Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 41 ACC-ZSM Zone Split ter Module (ACC-25/50ZS & ACC-25/50ZST) Field Programming 2.8.2 S2 and S3 Addressing Rot ary Switches T wo addressing switches are locat ed at the bottom right of the ACC-ZPMK Zone Page Module. The switches are used to set the ACS (EIA-485 ) address of the ACC-ZP[...]

42 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 Section 3: Inst allation 3.1 Mounting Options The cabinet may be surface mounted. The door is removable during th e installation perio d by opening and lifting it off the hinges. The cabinet mounts using two key slots at the top of the backbox and two add itional 0.250" diameter h[...]

Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 43 Backbox Installation Installation Draw wires through the respective knockou t locations. Top Right Side Left Side Figure 3.2 Cabinet Dimensions & Knockout Locations Bottom a c c 2 5 e n c . w m f Hinge Hinge Back of Box Back of Box Back of Box[...]

44 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 Installation Backbox Installation Figure 3.3 ACC-25/50 Series Backbox and Battery Box a c c 2 5 c a b . w m f Backbox = 4.75” (12.07 cm) with Door = 4.8” (12.19 cm) Backbox = 15.5” (39.37 cm) with Door = 15.78” (40.08 cm) Backbox = 4.22” (10.71 cm) with Door = 4.8” (12.19 c[...]

Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 45 Backbox Installation Installation 3.2.1 T ransformer Inst allation 1. Locate two threaded mounting studs and tw o mounting slots in the bottom left corner of the backbox (refer to backbox illustration below). 2. Position the Transformer Assembly with the bottom mounting brackets in the[...]

46 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 Installation Operating Power 3.3 Operating Power AC Power and Earth Ground Connection Primary power source fo r the ACC-25/50, ACC-25/50ZS, and ACC-25/ 50ZST is 120 V AC, 60 Hz, 1.5 amps. Overcurrent protection for this circui t must comply with Article 7 60 of the Natio nal Electrical[...]

Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 47 Operating Power Installation Use 14 A WG (1.6 mm O.D.) or heavier gauge wi re with 600V insulati on. No other equipment may be connected to this circuit and it may not contai n any power discon nect devices. A separate Earth Ground connection must be made to ensure pro per panel operat[...]

48 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 Installation Auxiliary DC Power Output Connections 3.4 Auxiliary DC Power Output Connections The Special Application Auxili ary DC power output is power-limited. 3.5 Input/Initiating Circuit s The ACC-25/50 Series has five Command Input ci rcuits, which are used to activate the panel a[...]

Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 49 Output Circuits Installation ble at the host F ACP . Note that CMD1 and CMD2 configurations can be independ ently set so that both circuits are triggered by the same type of input or by different types of inputs (see Figure 3.7 on page 49). CMD3, CMD4 and CMD5 Command Input circuits ar[...]

50 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 Installation Output Circuits In Example 1 illustrated below , the ACC-25/50 Series panel will trigger the ACC-25/50D A(s) when All-Call is activated for emergency or general paging. The maximum lin e resistance from the main ACC-25/50 Series to the last ACC-25/50DA is 200 ohms (100 ohm[...]

Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 51 Output Circuits Installation 3.6.2 T rouble Relay - TB1 The main circuit board p rovides a Form-C T rouble relay , for independent monitoring, rated for 2.0 amps @ 30 VDC (resistive) and 0.6 amp @ 30 V AC (r esistive). This relay is ‘fail safe’, meaning that it is normally energize[...]

52 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 Installation Output Circuits Shielded cable is not required, however, shielded cable will reduce RFI/EMI emissions and suscep- tibility . For additional inform ation, refer to “Wiring Requirements” on page 104 . 3.6.5 ACC-ZPMK Zone Page Mo dule - ACS Link (ACC-25/50ZS & ACC-25/[...]

Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 53 Output Circuits Installation ule to the ACS term inal on the F ACP . Circuit wiring requires a ferrite bead as illustrated in Figure 3.13. Note that the ACC-ZPMK must be set to addr ess 01 in order to communicate with the F ACP . ACC-ZPMK TB1 TB2 To FACP ACS Terminal Address 01 Set S2 [...]

54 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 Installation Output Circuits 3.6.6 ACC-ZSM Zone Splitte r Module (ACC-25/50ZS & ACC- 25/50ZST) The ACC-ZSM Zone Splitter Module provides conn ections for four Style Z (Class A) or eight Style Y (Class B) speaker circuits. Circuits are configured by setting switch SW2 on the ACC- ZS[...]

Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 55 Output Circuits Installation 3.6.7 ACC-FFT Fire Fighter T elephone Module ( ACC-25/50ZST Only ) The ACC-FFT provides connection for a single Style Y (Class B) or S tyl e Z (Class A) telephone audio circuit. In addition, a terminal b lock is provided for connection t o an FC-RM Remote M[...]

56 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 Installation UL Power-limited Wiring Requirements 3.7 UL Power-limited Wiring Requirement s Power-limited and nonpower-limited circuit wiring must remain separated in the cabinet. All power-limited circuit wiring must remain at least 0.25" away from any nonp ower-limited circuit w[...]

Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 57 Installation of Option Modules Installation 3.8 Inst allation of Option Modules 3.8.1 Audio Amplifie r Module (ACC-AAM25) The optional audio amplifier module is identical to the modu le provided with the factory standard panel configuration. It can be used to provide a second 25 watt s[...]

58 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 Installation Installation of Option Modules 8. Connect field wiring to newly installed amplifi er . Refer to Figure 3.12 on page 52 for illustration of speaker connecti ons if amplifier i s being used to exp and system power to 50 watts (i.e. providing dual 25 watt speaker circui ts). [...]

Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 59 Installation of Option Modules Installation 6. Secure the FC-XRM70 Transformer Module(s) to the Audio Amplifier Module(s) with the supplied screws. 3.8.3 Local Playback Speaker Module (FC-LPS) The Local Playback Speaker Module can be used to monitor the recorded digital messag e withou[...]

60 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 Installation Installation of Option Modules 5. When testing is completed, remove the FC-LPS and standof f and rein stall the screw . The FC-LPS is not approved for permanent connection. 3.8.4 ACC-EPM External Page Module The ACC-EPM External Page Module can be used to interface an exis[...]

Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 61 Installation of Option Modules Installation 4. T est the system to en sure proper operation . Figure 3.20 ACC-EPM External Page Module Installation P13 Connector on main circuit board J1 connector on ACC-EPM ACC-25/50 Series Main Circuit Board From external page system audio (600  ,[...]

62 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 Notes[...]

Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 63 Section 4: Operating Instructions 4.1 Switch Functions 4.1.1 Single Zone Operation (ACC-25/50, ACC-25/50ZS, ACC-25/50ZST) Figure 4.1 d epicts Single Zone o peration with th e maximum capacity of five messages. Single Zone may be configured for t wo to five message control (refer to Sec[...]

64 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 Operating Instructions Switch Functions 4.1.3 RECORD/PLA YBACK – for recording messages when Record/Bypass switch is in the up Record position (refer to Sections “S2 - Record Bypass Switch on AC C-25/50 Series Motherboard (ACC -MCB)” on page 38, Section “S1 DIP Switch Settings [...]

Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 65 Switch Functions Operating Instructions 8. Press and release the push-button on the keypad (Message 1 to Message 5) associated with the voice message that will be changed. The selected Message push-button will i lluminate steady and all others will extinguish. 9. The green LED on the R[...]

66 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 Operating Instructions ACC-ZPMK Switch Functions (ACC-25/50ZS & ACC-2 5/50ZST) 6. T o end the playback function, press and re lease the Record/Playback push-button. The Record/Playback LED will extinguish and th e Message push-button will stop flashing. 4.1.7 Main Control Panel Key[...]

Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 67 ACC-FFT Answer Call Pu sh-Button (ACC-25/50ZST) Operating Instructions 4.3 ACC-FFT Answer Call Push-Button (ACC-25/50ZST) When a Fire Fighter inserts the FF T Handset (FHS -F) into a rem ote FFT jack (FP J-F or RPJ-F), the Answer Call LED wi ll flash and the pi ezo will beep. Pressing [...]

68 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 Operating Instructions LED Indicators Message 1 This green LED turns on steady to indicate that Me ssage 1 has been activated by an alarm or man- ually . Note that during the recor ding pr ocess, when the push-butt on is pr essed, the LED will flash at a ½ second rate to indicate that[...]

Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 69 LED Indicators Operating Instructions Zone/Circuit Trouble A yellow LED corresponding to each of the 24 circ uits on the ACC-ZPMK Zone Page Module. The LED turns on when the circuit, which has b een activated under prog ram control during an alarm, is turned of f by pressing the corres[...]

70 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 Operating Instructions Operation Ground Fault (main c ircuit board) This yellow LED turns on steady when a gro und fault condition (zero impedance to ground) is detected on the system. Amp Supv - Supervision (Audio Amp lifier Module) This green LED (one on each amplif ier), when on ste[...]

Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 71 Operation Operating Instructions  T urn on the appropriat e Zone and Message 1 LED steady  T urn on selected Notificatio n Appliance Circuit speaker(s)  T urn on selected Audio Am plifier(s)  T ransmit the tone before message if programmed  T ransm it the appropriate dig[...]

72 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 Operating Instructions Operation fr om the local/ integral micr op hone will override paging operations fr om the opt ional Remote Micr ophone. Refer to Sect ion “S3 DIP Switch Settings on ACC-25 /50 Motherboard (ACC-MCB)” on page 37 and the ACC-25/50DA Manual , Document #5226 5, f[...]

Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 73 Operation Operating Instructions All-Call General Page Using Optional Remote Microphone Pressing the remote microphone push-to-talk swit ch will direct paging audio to all Zone Page Mod - ule speaker circuits, and illumin ate the All-Call and Audio On/Off buttons on the keypad. Note th[...]

74 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 Operating Instructions Operation Emergency Page Using Local/Integral Microphon e Pressing the local microphone pu sh-to-talk switch will interrupt the tone/voice message and direct paging audio to the Audio Amplifier Mod ule (ACC-AAM25) speaker circuit(s). The system will revert back t[...]

Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 75 Operation Operating Instructions General Page Using Optional Remote Microphone Pressing the remote micropho ne push-to-talk swi tch will direct paging audio to all speaker ci rcuits on the Zone Page Module. Refer to Section “All-Call General Page Usin g Optional Remote Micro - phone?[...]

76 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 Operating Instructions Operation Annunciation of Remote Telephone Locations (MS-9600 or MS-9200UDLS only) In addition to the operation d escribed in Section , ”Com munication on t he T elephone Loop”, one of the 24 corresponding FFT LEDs on the ACC-FFT k eypad will illum inate to i[...]

Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 77 Operation Operating Instructions Background Music • When background mu sic option is enabled via S5 DIP switch 3 , the ACC-25/50 will constantly monitor the extern al audio input RCA Jack. Both amplifiers and speaker wiring continu e to be fully superv ised when background * music is[...]

78 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 Operating Instructions Operation 4.5.13 T ro uble Condition Resto ral All trouble condition resto rals will cause the following to occur (note that re sponse to AC loss restoral will depend on the setting of S3 switch 8 as shown in T able 2.3 on page 34):  Reenergize the trouble rel[...]

Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 79 Operation Operating Instructions Remote Microphone restoral • T urn off the Remote Microphone Trouble LED located on the FC-MIM module for the ACC- 25/50 or ACC-25/50ZS • T urn off the Remote Key/Microphone Trouble LED located on the ACC-25/50ZST ACC-FFT module Power ON LED - power[...]

80 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 Section 5: Application Examples The AUDIO•COMMAND•CENTER•25/50, AU DIO•COMMAND•CENTER•25/50ZS, and AUDIO•COMMAND•CENTER•25/50ZST are voice evacuation control pa nels wh ich can be used, with a variety of Fire Alarm Control Panels, to provide emergency audio messages .[...]

Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 81 One Speaker Circuit With Backup on ACC-25/50 Application Examples In this application, the system may also be manual ly activated via the keypad by selecting the Building Speakers zone p ush-button followed by the selection of the Fir e Message push-butt on, or by using the microphone [...]

82 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 Application Examples One Speaker Circuit Wi th Backup on ACC-25/50 Backup Amplifier switch S1 is set to the ‘Bac kup ON’ position. 18 A WG or lar ger jum pers con- nect the Backup Amplifier TB2 T erminal 3 and Main Amplifier TB2 T erminal 1 as well as Backup Amplifier TB2 T erminal[...]

Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 83 Two Speaker Circuits on ACC-25/50 Application Examples 5.3 T wo Speaker Circuit s on ACC-25/50 Dual Output Zone, Single Input Channel - tone/v oice message (see T able 2.7 on page 37 for Mes- sage Control switch settings). This application consists of one ACC-25/50 Series with tw o spe[...]

84 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 Application Examples Two Speaker Circuits on ACC-25/50 Figure 5.3 Two Speaker Circuits - Du al Output Zon e, Dual Input Channel 4.7K  End-of-Line Resistors (P/N: 27072) ACC-25/50 Series Main Circuit Board Supervisory Polarity Shown Supervisory Polarity Shown a c 2 5 a p p 6 . w m f [...]

Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 85 Two Speaker Circuits on ACC-25/50 Application Examples 5.4 T wo Speaker Circuit s on ACC-25/50 Single Output Zone, Five Input Channels - five messages (see T able 2.7 on page 37 for Message Control switch settings). This application consists of one ACC-25/50 Series with tw o speaker ci[...]

86 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 Application Examples Two Speaker Circuits on ACC-25/50 MASTER CMD OUT TB6 1 2 3 4 + + - - TB1 TB1 TB2 TB2 + + + + + + + + - - - - - - - - + + + + - - - - 1 2 3 4 1 2 3 4 CMD1 CMD2 CMD3 CMD4 CMD5 TB5 TB8 TB9 TB10 TB2 + - + - + - 1 2 1 2 1 2 1 2 3 4 1 2 3 4 5 6 1 2 3 4 5 6 Figure 5.4 Two[...]

Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 87 ACC-25/50ZS & ACC-25/50ZST Zo ne Splitting Applications Application Examples 5.5 ACC-25/50ZS & ACC-25/50ZST Zone S plitting Applications 5.5.1 25 W att Zone Splitting - Eight S peaker Circuit s, Style Y (Class B) 25 watts total power with automatic control via ACS li nk from F [...]

88 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 Application Examples ACC-25/50ZS & ACC-25/50ZST Zone Splitting Applications AAM 1 & 2 AAM1 JP1 TB1 TB9 TB4 SW2 SW1 TB5 TB6 CLASS A CLASS B + - + - + - shield + - + - + - + - + - + - shield shield shield TB1 TB2 P1 S1 BACK-UP ON J1 1 2 3 4 5 6 7 8 ON S1 ON S3 0 5 4 3 2 1 9 8 7 6[...]

Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 89 ACC-25/50ZS & ACC-25/50ZST Zo ne Splitting Applications Application Examples 5.5.2 25 W att Zone Splitting - Four S peaker Circuit s, Style Z (Class A) 25 watts total power w ith automatic control via ACS link from the F ACP (see T able 2.7 on page 37, T able 2.8 on page 40, an d ?[...]

90 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 Application Examples ACC-25/50ZS & ACC-25/50ZST Zone Splitting Applications AAM 1 & 2 AAM1 JP1 TB1 TB9 TB4 SW2 SW1 TB5 TB6 CLASS A CLASS B + - + - + - shield + - + - + - + - + - + - shield shield shield TB1 TB2 P1 S1 BACK-UP O N J1 1 2 3 4 5 6 7 8 ON S1 ON S3 0 5 4 3 2 1 9 8 7 [...]

Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 91 ACC-25/50ZS & ACC-25/50ZST Zo ne Splitting Applications Application Examples 5.5.3 50 W att Zone Splitting - Eight S peaker Circuit s 50 watts total power w ith automatic control via ACS link from the F ACP (see T able 2.7 on page 37, T able 2.8 on page 40, an d “ACC-ZSM Zone Spl[...]

92 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 Application Examples ACC-25/50ZS & ACC-25/50ZST Zone Splitting Applications AAM 1 & 2 AAM1 JP1 TB1 TB9 TB4 SW2 SW1 TB5 TB6 CLASS A CLASS B + - + - + - shield + - + - + - + - + - + - shield shield shield TB1 TB2 P1 S1 BACK-UP ON J1 1 2 3 4 5 6 7 8 ON S1 ON S3 0 5 4 3 2 1 9 8 7 6[...]

Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 93 ACC-25/50 and ACC-25/50DA Installation Application Examples 5.6 ACC-25/50 and ACC-25/50DA Inst allation Audio•Command•Center•25/50 Connect ion to Multiple Audio•Command•Center•25/50 Dist ributed Audi o Panels ( see Table 2.7 on page 37 for Message Control switch setting s a[...]

94 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 Application Examples ACC-25/50 and ACC-25/ 50DA Installation MASTER CMD OUT TB6 1 2 3 4 + + - - TB1 TB1 TB2 TB2 + + + + + + + + - - - - - - - - + + + + - - - - 1 2 3 4 1 2 3 4 CMD1 CMD2 CMD3 CMD4 CMD5 TB5 TB8 TB9 TB10 TB2 + - + - + - 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 1 2 3 4 1 2 1 2 1 2 [...]

Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 95 16 Theater Cineplex Utilizing A CC-25/50ZS With ACC-25/50DAZS Application Examples 5.7 16 Theater Cineplex Utilizing ACC-25/50ZS With ACC- 25/50DAZS In this application, t he Fire Protection System con sists of one ACC-25/50ZS w ith one ACC- 25/50DAZS, 16 zones and an addressable F ACP[...]

96 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 Application Examples Audio Command Center 24 Zone System 5.8 Audio Command Center 24 Zone System In this applicatio n, the Fire Protection System consists of one ACC-25/50ZS panel with two ACC- 25/50DAZS panels, 24 zone s and an F ACP . Automatic control by the F ACP is provided throug[...]

Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 97 Audio Command Center 24 Zone System App lication Examples TB1 TB2 P1 SW1 BACK-UP ON CKT TBL AMP S UPV J1 1 2 3 4 5 6 7 8 ON S1 ON S3 0 5 4 3 2 1 9 8 7 6 0 5 4 3 2 1 9 8 7 6 S2 TENS ONES 1 2 3 4 5 6 7 8 ON S1 ON S3 0 5 4 3 2 1 9 8 7 6 0 5 4 3 2 1 9 8 7 6 S2 TENS ONES AAM 1 & 2 AAM1 [...]

98 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 Section 6: Power Supply Calculations 6.1 Overview This section contains instructions and tables fo r calculating power supply currents in alarm and standby conditions. This is a four-step process, consisting of the following: 1. Calculating the total amount of AC branch circuit current[...]

Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 99 Calculating the System Current Draw Power Supply Calculations 6.3.2 How to use T able 6.2 to calculate system current dr aws 1. Enter the quantity of devices in both columns. 2. Enter the DC current draw where required. Refer to the Fir e•Lite Device Compatibi lity Document for compa[...]

100 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 Power Supply Calculations Calculating the Battery Size 6.4 Calculating the Battery Size Use T able 6.3 to calculate the total Standby and Alar m load in ampere hours (AH). This total lo ad determines the battery size (in A H), required to s upp ort the ACC-25/50 Series under the loss [...]

Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 101 Notes[...]

102 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 Appendix A: Digit al V oice Messages The AUDIO•COMMAND•CEN TER•25/50 Series digital messag e generator provides a 60 second record time which allows for a single fire messag e of 60 seconds length, two 30 second messages, three 20 second messages, four 15 second messages or five[...]

Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 103 Appendix B: Addressable Module Connections When configured with an addressable F ACP such as the MS-9200UDLS, MS-9200UD, MS-9200C(E), or MS-9600, the AUDIO•C OMMAND •CENTER•25/50 Series may be triggered either by the F ACP main NAC output or from addressable control modules. Fig[...]

104 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 Appendix C: Wiring Requirement s Connecting external system accessories to the AUDIO•COMMAND •CENTER•25/50 Series main circuits must be carefully consider ed to ensure proper operation. It is important to use the correct type of wire, wire gauge and wire run length per each circ[...]

Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 105 Appendix D: Programmed Activation by F ACP The Audio Command Center Zone Split system (ACC-25/50ZS/T) can be autom atically controlled by any F ACP . The following table lists the availabl e audio features and the control signals that are required from the F ACP . Column Descriptions [...]

106 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 Programmed Activation by FACP MS-9600, MS-9200UDLS and MS-9200UD • Simultaneous Activation of All Audi o Zones - this is a sing le trip mechanism via a zone on the ACS/ANN-BUS link or CMD input tri gger that ac tivates all the audio zones at the same time (refer to the F ACP specifi[...]

Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 107 MS-9600, MS-9200UDLS and MS-92 00UD Programmed Activation by FACP 3. Set DIP Switches 1, 2, and 3 on Switch S1 of the ACC-ZPMK for operation with the MS-9600, MS-9200UD, MS-9200UDLS F ACP and switches 6, 7, and 8 for the number of ACC- 25/50DAZS panels. 4. Set Switch SW1 on the ACC-ZS[...]

108 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 Programmed Activation by FACP MS-9600, MS-9200UDLS and MS-9200UD D.1.4 ACC-25/50ZS and ACC-25/50ZST Switch Settin gs ACC-ZPMK DIP Switch S1 • Switches 1, 2, and 3 are used to configure the A CC-25/50ZS and ACC-25/50ZST for o peration with a specific F ACP as sh own in the following [...]

Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 109 MS-9600, MS-9200UDLS and MS-92 00UD Programmed Activation by FACP D.1.5 F ACP Programming The MS-9600, MS-9200UDLS, and MS-9200UD F ACPs must be p rogrammed to operate with the ACC-25/50ZS or ACC-25/50ZST Audio Control Center . The following table su mmarizes the steps involved in pro[...]

110 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 Programmed Activation by FACP MS-9600, MS-9200UDLS and MS-9200UD Note that Zone 32 is assigned to all speaker circ uits. If an addressable device programmed to Zone 32 is activated, the message programmed to Zone 32 will be generated to all speaker circuits. The exception is when one [...]

Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 111 MS-9600, MS-9200UDLS and MS-92 00UD Programmed Activation by FACP • if an addressable device programmed to Zone 35 is activated and no ot her devices are active, the message programmed for Zone 35 will be ge nerated ov er speaker circuit 3 on the ACC- 25/50ZS or ACC-25/50ZST . (Refe[...]

112 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 Programmed Activation by FACP MS-9600, MS-9200UDLS and MS-9200UD Message Assignment - Zone Specific The F ACP can be programmed to allow a specific addressable input device to generate one of five messages over any speaker circuit. Any one of th e five messages can be programmed to ea[...]

Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 113 MS-9600, MS-9200UDLS and MS-92 00UD Programmed Activation by FACP Access Programming Mode by pressing the 2 key . The following screen will be displayed: Entering the Maste r level password (default 0 0000 ) will cause the fo llow ing screen to appear: Select the Zone Setup option by [...]

114 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 Programmed Activation by FACP MS-9600, MS-9200UDLS and MS-9200UD Pressing 3 while viewing Zone Setup Screen #3 will cause the followin g screen to be displayed: Press the down arrow k ey until the following screen i s displayed. The default setting is No Message for each speaker circu[...]

Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 115 MS-9600, MS-9200UDLS and MS-92 00UD Programmed Activation by FACP Fire Fighter Telephone SLC Point Assignment If annunciation of remote FFT locat ions is desi red on the ACC-FFT keypad, an add ressable input device must be programmed as a PHONE type on the MS-9200UDLS or MS-9600. Prog[...]

116 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 Programmed Activation by FACP MS-9600, MS-9200UDLS and MS-9200UD T o Pr ogram a monitor module in an FPJ-F or RPJ-F , press the ENTER key at the F ACP . The fol- lowing screen will be displayed: Access Programming Mode by pressing the 2 key . The following screen will be displayed: AC[...]

Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 117 MS-9600, MS-9200UDLS and MS-92 00UD Programmed Activation by FACP Entering the Maste r level password (default 0 0000 ) will cause the fo llow ing screen to appear: Access Point Programming by pressing the 2 key . The following screen will be displayed: Press the 2 key to alter the pr[...]

118 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 Programmed Activation by FACP MS-5210UD Press down arrow key once: Press 2 to edit the type, then press the down arrow key six times: Press 1 to select PHONE type. Repeat the above steps for each re maining R PJ-F or FPJ-F location. D.2 MS-5210UD Refer to the MS-5210UD manual, Documen[...]

Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 119 MS-5210UD Programmed Activation by FACP If only the generat ing Fire Evacuation announ cemen t (Message #1) to individual audi o zones is desired, do not connect the MS-5210UD Relay out puts to t he ACC-25/50ZS or ACC-25/50ZST CMD inputs. In this case, the act ivation of the aud io zo[...]

120 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 Programmed Activation by FACP MS-5210UD ACC-ZPMK Zone Page Module Rotary switches S2 an d S3 •S 2 = 0 •S 3 = 1 ACC-ZSM Zone Splitter Module Switch Set tings [refer to Section “ACC- ZSM Zone Splitter Mod- ule (ACC-25/50ZS & ACC-25/50 ZST)” on page 41 for additional info rma[...]

Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 121 MS-5210UD Programmed Activation by FACP ACC-25/50ZS and ACC-25/50ZST Switch Settings ACC-ZPMK Zone Page Module DIP Switch S1 • Switches 1, 2, and 3 are set to O FF , OFF , OFF for No ACS link operation • Switch 4 (future use) is set to OFF • Switches 5, 6, 7, and 8 are set to OF[...]

122 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 Programmed Activation by FACP MS-9200(E) D.3 MS-9200(E) The ACC-25/50ZS an d ACC-25/5 0ZST can be automatically triggere d via the ACS serial link by the MS-9200(E) to transmit one of five messages over selected speaker zones. This is accom- plished by zone programming at the F ACP . [...]

Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 123 MS-9200(E) Programmed Activation by FACP In this example, the M S-9200 can route the Fire Evacuat ion message (messag e #1) to the activated audio zones via zone programming. The CMD inputs are not used to activate the audio panel. The audio panel defaults to activating the Fire Evacu[...]

124 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 Programmed Activation by FACP MS-9200(E) D.3.3 Wiring Fr om ACC-25/50ZS or ACC-25/50ZST to MS-9200(E) The MS-9200(E) F ACP communicates with th e ACC-25/50ZS or ACC-25/50ZST over the ACS annunciator link. Wi ring must be connected between the ACS T erminal TB5 on the MS-9200(E) and AC[...]

Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 125 MS-9200(E) Programmed Activation by FACP ACC-25/50ZS & ACC-25/50ZST Switch Settings ACC-ZPMK DIP Switc h S1 • Switches 1, 2, and 3 are used to configure the ACC-25/50ZS/T for operation with a specific F ACP (See T able 2.4 on page 35.) • Switch 4 - future use • Switches 5, 6[...]

126 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 Programmed Activation by FACP MS-9200(E) Note that Zone 32 is assigned to all speaker circ uits. If an addressable device programmed to Zone 32 is activated, the message will be generated to all speaker circuits. The ex cepti on is when one or more devices programmed to Zones 33 thro [...]

Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 127 MS-5UD-3/7 and MS-10UD-3/7 Programmed Activation by FACP D.4 MS-5UD-3/7 and MS-10UD-3/7 The ACC-25/50ZS and ACC-25/50ZST can be auto matically triggered via the ANN-BUS serial link by the MS-5UD-3/7 or MS-10UD-3 /7 (version 2 or higher), to transm it one of five messages over selected[...]

128 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 Programmed Activation by FACP MS-5UD-3/7 and MS-10UD-3/7 D.4.3 ACC-ZPMK DIP Switch 1 Settings on ACC-25/50ZS and ACC-25/50ZST Switches 1, 2, and 3 are used to configure the ACC-25/50ZS and ACC-25/50ZST for operation with a specific F ACP . The switch settings for use with the MS-5UD-3[...]

Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 129 MS-5UD-3/7 and MS-10UD-3/7 Programmed Activation by FACP D.4.4 Wiring From ACC-25/50ZS or ACC-25/50ZST to F ACP The F ACP communicates with the ACC-25/50ZS/T over the ACS or ANN-BUS annunciator link. W iring must be connected betw een T erminal TB6 on the F ACP and T erminal TB1 on th[...]

130 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 Programmed Activation by FACP MS-5UD-3/7 and MS-10UD-3/7 • Switches 5, 6, 7, and 8 - used to set the number of ACC-25/50DAZS pan els installed. ACC-ZPMK Rotary Address Switches S2 and S3 The address switches can be set to any address from 01 t hrough 08 to co mmunicate with t he F A[...]

Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 131 MS-5UD-3/7 and MS-10UD-3/7 Programmed Activation by FACP Note that when the ANN-BUS Annu nciator option is enabled at the F ACP , speaker circuits at the ACC-25/50ZS or ACC-25/50ZST are automatically assi gned dedicated zone numbers. These zone numbers can then be programmed to addres[...]

132 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 Programmed Activation by FACP MS-5UD-3/7 and MS-10UD-3/7 Access Programming Mode by pressing the 2 key . The following screen will be displayed: Entering the Maste r level password (default 0 0000 ) will cause the fo llow ing screen to appear: Select the Input Zone option by p ressing[...]

Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 133 MS-5UD-3/7 and MS-10UD-3/7 Programmed Activation by FACP Press the down arrow k ey 3 times un til the following screen is displayed. Press the 2 key to display the following screen: Using these screens, the programmer can assign an audio message to each input zone. The selected messag[...]

134 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 Programmed Activation by FACP MS-5UD-3/7 and MS-10UD-3/7 The following screen will be displayed: Entering the Maste r level password (default 0 0000 ) will cause the fo llow ing screens to appear: Access Option Modules by pressing the 2 key while viewing Programmi ng Screen #2. The fo[...]

Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 135 MS-5UD-3/7 and MS-10UD-3/7 Programmed Activation by FACP Press the 1 key to access the first ANN-BUS pr ogramming screen as shown below Press the down arrow key twice to view the follo wing screen: Pressing 1 for ANN-AUDIO Options while viewing A NN-BUS Screen #3 will cau se the follo[...]

136 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 Programmed Activation by FACP MS-5UD-3/7 and MS-10UD-3/7 This screen shows the Input Zone that has been as signed to be the All-Call Zone. In this exam ple, Zone 1 is the All-Call Zone. The All-Call Zone can be changed by pressing the 1 key whi le view- ing the ANN-AUDIO Options Scree[...]

Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 137 Notes[...]

138 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 Index A AC branch circuit calculation 98 AC Loss Relay 15 , 16 , 19 , 27 , 51 Contact Rating 27 , 51 AC Loss Response 76 AC On LED 25 AC Power 19 see also Power On 69 see also Primary Power 46 wiring 46 ACC Communication 68 ACC-25/50 26 see also Audio•Co mmand•Center•25/50 13 se[...]

Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 139 Index C–F Charger Capacity 20 Charging Circuit 20 Precaution 47 see also Secondary Power 47 Battery Box 44 battery charger enable/disable 39 battery requirements NFPA 100 battery selection 100 battery size calculation 100 Battery Trouble LED 25 , 69 Battery Trouble Response 76 board[...]

140 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 G–M Index see also Remote Microp hone 15 , 22 , 27 FC-XRM70 28 , 29 Installation 57 , 58 see also Audio Co nversion Module 28 see also Transformer Modul e 58 Fire Alarm Control Panel see also FACP 13 Fire Alarm Operation 70 Fire Alarm Restoral 70 Fire Fighter Telephone Module 21 , 2[...]

Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 141 Index N–R see also FC-MIM 15 , 27 Microphone Recording 37 Microphone Trouble LED 24 , 67 Microphone Trouble Response 76 Modules Optional 57 Mounting surface 42 Mounting Cabinet Surface Mount 42 Mounting Panel 42 MR-101C 21 , 50 MR-201C 21 , 50 MS-10UD 127 MS-5UD 127 MS-9200UD 106 MS[...]

142 Audio Command Center Series Manual — P/N 51889:E1 6/8/2010 S–Z Index Operation 77 see also FC-RM 15 , 22 , 27 Remote Microphone Installed Switch see also SW1 39 Remote Microphone Module 21 Remote Microphone Page 25 Remote Microphone Page LED 69 Remote Microphone Trouble 25 Remote Microphone Trouble LED 69 , 70 Remote Phone Jack Keyswitch 21[...]

Manufacturer W arranties and Limit ation of Liability Manufacturer W arranties. Subject to the limita tions set forth herein, Manufacturer warrants tha t the Products manufactured by it in its Northford, Connecticut facility and sold by it to it s authorized Distributors shall be free, under no rmal use and service, from defects in material and wor[...]

Wor ld Headquarte rs 1 Firelite Plac e Northford, CT 06472- 1653 USA 203-484-7161 fax 203-484-71 18 www .firelite.com[...]