Honeywell Granit 1981i инструкция обслуживания

Granit 1981i Industrial Full Ran ge Wireless Area-Imaging Scanner Quick Start Guide GRNT1981-QS Rev A 12/14 Aller à www.honeywellaidc.com pour le français. Vai a www.honeywellaidc.com per l'italiano. Gehe zu www.honeywellaidc.com für Deutsch. Ir a www.honeyw ellaidc.com para español. Para Português, acesse www.hone ywellaidc.com.br . Пе[...]

Note: Refer to your user’s gu ide for information about cleaning your device. For localized l anguage versi ons of this document, go to www.honeywellaidc.com . Getting Started Turn off th e computer’s power be fore connecting the base, then power up the computer once the bas e is fully connected. When the base is connected and powered up, put t[...]

Connecting the Base USB:[...]

Ke yboard W edge: RS232 Serial P ort:[...]

Reading T echniques Near Distance Scanning Use the red lighting and center the bo x over the bar code when scanning at a near distance (less than 1 1.8 inches / 30 cm). The laser aimer will be to the rig ht of the center of the bar code. Far Distance Scanning Use the laser aimer and aim at the center of the bar code when scanning at a far distance [...]

Standard Pr oduct Defaults The following bar code rese ts all standard product default settings. USB Serial Scan the following cod e to program the scanner to emulate a regular RS232-based COM Port. If you are using a Microsoft® Windows® PC, you will need to download a driv er from the Honeywell website (www.honeywellaidc.com) . The driver will u[...]

Ke yboard Country Scan the Program Keyb oard Country bar code below, th en scan the numeric bar code(s) from page 13 , then the Save bar co de to program the keyboard for your country. As a general rule, the following characte rs are not suppor ted by the scanner for countries other than the Un ited States: @ | $ # { } [ ] = / ‘ < > ~. No[...]

Lock ed Link If you link a scanner to a base us ing the Locked Link Mode, other scanners are blocked from being linked if they are inadverte ntly placed into the base . If you do place a different scanner into the base, it will charge the scan ner, but the scanner will no t be linked. To use a different scanner, you need to un link the original sca[...]

Aimer Delay Set the time between when the trigger is pulled, turning the laser aimer on, and when the picture is ta ken. During the delay time , the laser aimer appears so you can find the bar code. When the d elay is over the LEDs turn on and the sca nne r reads the bar code. This can be helpful when reading at far distances. Note: For more option[...]

Suffix If you want a carriage return after the bar code, scan th e Add CR Suffix bar code. To add a tab after the bar code , scan the Add T ab Suffix bar code. Otherwise, scan the Remo ve Suffix bar co de to remove the suffixes. Add Code ID Prefix to all Symbologie s Scan the following bar code if you wish to add a Code ID prefix to all symbologie [...]

Function Code T r ansmit When this selection is enabled and function codes are contain ed within the scanned da ta, the sca nner transmits the function code to the terminal. Charts of these func tion codes are provid ed in your User’s Guide. When the scanner is in keyboard wedge mo de, the scan code is converted to a key code before it is transmi[...]

Data Format Editor Instructions The following are abbreviated instruction s for entering a data format. For complete instructions refer to your User’s Guide, available at our website, www.honeywellaidc.com. 1. Scan the Enter Data Format sym bol. 2. Primary/Alternate Format: scan 0 for Primary Format 3. Terminal Type: scan 099 for any terminal typ[...]

Pr ogramming Char t 0 2 1 4 3 5 6 7[...]

A B C D E F 9 8 Save[...]

EZConfig-Scanning To access additional features fo r the scanner use EZConfig- Scanning, an online configuration so ftware tool, availabl e from our websit e at www.honeywellaidc.com. T echnical Assistance Contact information for technical suppo rt, product service, and repair can be found at www.honeywellai dc.com . Limited W a rranty Refer to www[...]