Honeywell MS3780 Fusion инструкция обслуживания

[...]

Copyright © 2007 by Metrologic Instruments, Inc. All rights reserved. No part of this work may be reproduced, transmitted, or stored in any for m or by any means without prior written consent, except by reviewer, who may quote br ief passages in a review, or provided for in the Copyright Act of 1976. Trademarks Metrologic is a registered trademark[...]

Table of Contents iii T ABLE OF C ONTENTS Introduction Symbol Key ................................................................................................. xi Bar Code Configuration Methods Single-Code Method ................................................................................... xii Multi-Code Method ...........................[...]

Table of Contents iv T ABLE OF C ONTENTS Section B: Supplements Two Digit Supplements/Redundancy ........................................................... 1 Five Digit Supplements/Redundancy ........................................................... 1 Supplements Required/Not Required ........................................................... 2[...]

Table of Contents v T ABLE OF C ONTENTS ISBN Re-Formatting ..................................................................................... 9 ISSN Check Digit Transmission ................................................................. 10 ISSN Re-Formatting ................................................................................... 1[...]

Table of Contents vi T ABLE OF C ONTENTS Same Symbol Time Outs.............................................................................. 8 Barcode Absence ......................................................................................... 9 LED Options .......................................................................................[...]

Table of Contents vii T ABLE OF C ONTENTS Telepen......................................................................................................... 9 Plessey ....................................................................................................... 10 2 of 5........................................................................[...]

Table of Contents vii i T ABLE OF C ONTENTS Section J: Light Pen/Laser Emulation Enable Light Pen Mode ................................................................................ 1 Space/Bar Height ......................................................................................... 1 Transmit Code 39 ......................................[...]

Table of Contents ix T ABLE OF C ONTENTS Section N: Miscellaneous Features Custom Defaults ........................................................................................... 1 Serial Configuration Mode ............................................................................ 5 Software/Serial Number .....................................[...]

Table of Contents x T ABLE OF C ONTENTS Inter-Character Delays ............................................................................... 15 Inter-Character De lays .............................................................................. 16 Section P: USB ...................................................................................[...]

Introduction xi I NTRODUCTION Your new scanner has been configured at the fa ctory with a set of default communication protocols. Since many host systems have unique formats and protocol requirements, Metrologic provides a wide range of configurabl e features that may be selected with the use of this bar code configuration guide. Once the configura[...]

Bar Code Configuration Meth ods xii B AR C ODE C ONFIGURATION M ETHODS Metrologic scanners can be bar code configured in two ways: the Single-Code Method and the M ulti-Code Method . Single-Code Meth od Most features can be enabled or disabled using the Single-Code Method. 1. Power up the scanner. 2. Scan the bar code(s) for the desired feature(s).[...]

Need to Start Over? xiii N EED TO S TAR T O VER ? Scan the Recall Default bar code. This will erase all previous settings and return to the scanner’s default communications protocol. • Keyboard Wedge interface scanners will load keyboard wedge defaults. • All other scanners will load RS232 defaults. Metrologic manufactures custom OEM scanners[...]

[...]

Code Types & Decode Rules A 1 S ECTION A UPC/EAN * Enable UPC/EAN Disable UPC/EAN ³ 1 00116 ³ 1 00106 * Enable UPC-A Disable UPC-A ³ 1 00216 ³ 1 00206 * Enable UPC-E Disable UPC-E ³ 1 00210 ³ 1 00200[...]

Code Types & Decode Rules A 2 S ECTION A UPC/EAN * Enable EAN-13 Disable EAN-13 ³ 1 00211 ³ 1 00201 * Enable EAN-8 Disable EAN-8 ³ 1 00214 ³ 1 00204 * Enable Auto Redundancy UPC-E Disable Auto Redundancy UPC-E ³ 1 01104 ³ 1 01114[...]

Code Types & Decode Rules A 3 S ECTION A C ODE 128 * Enable Code 128 Disable Code 12 8 ³ 1 00113 ³ 1 00103 Enable UCC/EAN-28 ‘]C1’ Code Formatting Disable UCC/EAN-128 ‘]C1’ Code Formatting ³ 1 00314 ³ 1 00304 For Coupon Code 128, see Section B, page 5.[...]

Code Types & Decode Rules A 4 S ECTION A C ODE 39 * Enable Code 39 Disable Code 39 ³ 1 00111 ³ 1 00101 Enable MOD 43 Check on Code 39 * Disable MOD 43 Check on Code 39 ³ 1 00213 The scanner will o nly scan Code 39 bar codes that have a valid M odulo 43 check digit. ³ 1 00203 The scanner will not tes t Code 39 bar code s for a modulo 43 chec[...]

Code Types & Decode Rules A 5 S ECTION A C ODE 39 Enable Full ASCII Code 39 * Disable F ull ASCII Code 39 ³ 1 00217 ³ 1 00207 Enable PARAF Support (Italian Pharmaceutical Codes) * Disable PARAF Support ³ 1 00215 The scanner will conv ert Code 39 bar codes to PARAF format. ³ 1 00205 The scanner will not c onvert code 39 bar codes to PARAF fo[...]

Code Types & Decode Rules A 6 S ECTION A I NTERLEAVED 2 OF 5 * Enable Interleave d 2 of 5 (ITF) Disable Interleaved 2 of 5 (ITF) ³ 1 00115 ³ 1 00105 Enable MOD 10 Check on ITF * Disable MOD 10 Check on ITF ³ 1 00310 The scanner will o nly scan Interleaved 2 of 5 (ITF) Bar codes that ha ve a Modulo 10 chec k digit. ³ 1 00300 The scanner will[...]

Code Types & Decode Rules A 7 S ECTION A I NTERLEAVED 2 OF 5 Enable ALT Check Digit ITF * Disable ALT Check Digit ITF ³ 1 00717 ³ 1 00707 Enable 12 Digit ITF Check Digit at 1 * Normal Check Digit ³ 1 00910 This feature requir es MOD 10 ITF Check Digit to be enabled. The 12- character ITF chec k digit calculation will s tart with 1 instead of[...]

Code Types & Decode Rules A 8 S ECTION A I NTERLEAVED 2 OF 5 ~ ITF Symbol Length Lock 1 † ~ ITF Symbol Length Lock 2 † ³ 9 01600 To specify a 1 st IT F symbol length lock, s can the abov e bar code and the appropriate code bytes located in Secti on M. † ³ 9 01700 To specify a 2 nd IT F symbol length lock, s can the abov e bar code and t[...]

Code Types & Decode Rules A 9 S ECTION A S TANDARD 2 OF 5 Enable Standard 2 of 5 * Disable Standard 2 of 5 ³ 1 00110 ³ 1 00100 ~ Standard 2 of 5 Symbol Length Loc k ³ 9 01500 To specify a mi nimum number of ITF cha racters to be decoded, sc an the above bar code and the appropriate code bytes located in Secti on M. † † Refer to the M ult[...]

Code Types & Decode Rules A 10 S ECTION A O THER 2 OF 5 C ODES Enable Matrix 2 of 5 * Disable Matrix 2 o f 5 ³ 1 00015 ³ 1 00005 Enable 15 Digit Airline 2 of 5 * Disable 15 Digit Airline 2 of 5 ³ 1 00014 ³ 1 00004[...]

Code Types & Decode Rules A 11 S ECTION A O THER 2 OF 5 C ODES Enable 13 Digit Airline 2 of 5 * Disable 13 Digit Airline 2 of 5 ³ 1 00313 ³ 1 00303 Enable Hong Kong 2 of 5 * Disable Hong Kong 2 of 5 ³ 1 00316 ³ 1 00306[...]

Code Types & Decode Rules A 12 S ECTION A C ODABAR * Enable Codabar * Disable C odabar ³ 1 00114 ³ 1 00104 Enable Dual Field Codaba r * Disable Dual Field Codaba r ³ 1 00012 ³ 1 00002 Enable Tab in Dual Codabar * Disable Tab in Dual Codabar ³ 1 08012 This feature requir es Dual Field Codabar to be enabled. The sc anner will insert a tab be[...]

Code Types & Decode Rules A 13 S ECTION A C ODE 93 AND C ODE 11 * Enable Code 93 Disable Code 93 ³ 1 00112 ³ 1 00102 Enable Code 11 * Disable C ode 11 ³ 1 00013 ³ 1 00003[...]

Code Types & Decode Rules A 14 S ECTION A T ELEPEN Enable Telepen * Disable Tel epen ³ 1 00017 ³ 1 00007 Enable ALPHA Telepen * Disable ALPHA Telepen ³ 1 00016 ³ 1 00006[...]

Code Types & Decode Rules A 15 S ECTION A P LESSEY C ODES Enable MSI Plesse y * Disabl e MSI Plessey ³ 1 00212 ³ 1 00202 * No MSI Plessey Check Digit ³ 2 00704 The scanner will not tes t MSI Plessey bar codes for a check digit. Enable MSI Plessey MOD 10/10 Check Digit * Enable MSI Plessey MOD 10 Check Digit ³ 2 00734 The scanner will t est [...]

Code Types & Decode Rules A 16 S ECTION A P LESS EY C ODES Transmit MSI Plessey Check Di git * Do Not Transmit MSI Plessey Check Di git ³ 1 07711 This option works in conjunction with one or both of the Enabled MS I Plessey Mode options. ³ 1 07701 The scanner will not transmit MS I Plessey check digit characters . Enable UK Ple ssey * Disable[...]

Code Types & Decode Rules A 17 S ECTION A O THER D ECODE F EATURES Enable Double Bo rder Required/Large Inter-Character Space * Disable D ouble Border Required/Large Inter-Character Space ³ 1 00011 ³ 1 00001 ~ Minimum Symbol Length † ~ Symbol Length L ock † ³ 9 01800 Omnidirect ional defa ult is 4. Combine this code with t he proper Code[...]

Code Types & Decode Rules A 18 S ECTION A C ONFIGURABLE C ODE L ENGTHS There are seven bar code lock lengths availabl e. Specific code types can be assigned to a lock length using the Multi-Code configuration method. Example: 1. Scan the enter/exit configuration bar code. 2. Scan the code length lock #1 bar code. 3. Scan the three Code Bytes th[...]

Code Types & Decode Rules A 19 S ECTION A C ONFIGURABLE C ODE L ENGTHS ~ Code Length Lock #3 ~ Code Type Lock #3 ³ 9 02400 ³ 9 02500 ~ Code Length Lock #4 ~ Code Type Lock #4 ³ 9 02600 ³ 9 02700 ~ Code Length Lock #5 ~ Code Type Lock #5 ³ 9 02800 ³ 9 02900[...]

Code Types & Decode Rules A 20 S ECTION A C ONFIGURABLE C ODE L ENGTHS ~ Code Length Lock #6 ~ Code Type Lock #6 ³ 9 03000 ³ 9 03100 ~ Code Length Lock #7 ~ Code Type Lock #7 ³ 9 03200 ³ 9 03300[...]

Code Types & Decode Rules A 21 S ECTION A RSS 14 F EATURES Enable RSS 14 * Disable RSS 14 ³ 1 00413 ³ 1 00403 * Transmit RSS 14 Check Digit Do Not Transmit RSS 14 Check Digit ³ 1 14900 ³ 1 14910[...]

Code Types & Decode Rules A 22 S ECTION A RSS 14 F EATURES * Transmit RSS 14 Application ID Do Not Transmit RSS 14 Application ID ³ 1 14901 Application iden tifier “01” is transmitted by d efault. ³ 1 14911 * Transmit RSS 14 Symbology ID Do Not Transmit RSS 14 Symbology ID ³ 1 14902 Symbology ident ifier “]e0” is transmitted by d efa[...]

Code Types & Decode Rules A 23 S ECTION A RSS L IMITED F EATU RES Enable RSS Limited * Disable RSS Limited ³ 1 00414 ³ 1 00404 * Transmit RSS Limited Check Digit Do Not Transmit RSS Limited Check Digit ³ 1 14903 ³ 1 14913[...]

Code Types & Decode Rules A 24 S ECTION A RSS L IMITED F EATU RES * Transmit RSS Limited Application ID Do Not Transmit RSS Limited Application ID ³ 1 14904 Application iden tifier “01” is transmitted by d efault. ³ 1 14914 * Transmit RSS Limited Symbology ID Do Not Transmit RSS Limited Symbology ID ³ 1 14905 Symbology ident ifier “]e0[...]

Code Types & Decode Rules A 25 S ECTION A RSS E XPANDED F EATURES Enable RSS Expanded * Disable RSS Expanded ³ 1 00415 ³ 1 00405 * Transmit RSS Expanded Symbol ogy ID Do Not Transmit RSS Expanded Symbol ogy ID ³ 1 14906 Symbology ident ifier “]e0” is transmitted by d efault. ³ 1 14916[...]

[...]

Supplements B 1 S ECTION B S UPPLEMEN TS /R EDUNDANCY Enable Two Digit Supplements * Disable Two Digit Supplements ³ 1 01217 ³ 1 01207 * Enable Two Digit Redundancy Disable Two Digit Redundancy ³ 1 01212 Twice before acc epting data, the scann er will scan the bar code plus the two digit add on. ³ 1 01202 When scanned, will n ot implement the t[...]

Supplements B 2 S ECTION B S UPPLEMEN TS /R EDUNDANCY Enable Five Digit Redundancy * Disable Five Digit Redundancy ³ 1 01211 Twice before acc epting data, the scann er will scan the bar code plus the five digit add on. ³ 1 01201 The scanner will not implement the fiv e digit redundancy feat ure. Supplements are Required * Supplements are not Requ[...]

Supplements B 3 S ECTION B S UPPLEMEN TS Enable Bookland ( 978) Supplement Requi rement * Disable Book land (978) Supplement Requi rement ³ 1 01417 ³ 1 01407 Enable 977 (2 digit) Supplemental R equirement * Disable 97 7 (2 digit) Supplemental Requirement ³ 1 01314 The scanner will r equire a 2 digit supplem ent be scanned when an EAN-13 code beg[...]

Supplements B 4 S ECTION B S UPPLEMEN TS Enable 434/439 German Supplemental R equirement * Disable 434/439 German Supplemental Requirement ³ 1 01415 ³ 1 01405 Enable 414/419 German Supplemental R equirement * Disable 41 4/419 German Supplemental R equirement ³ 1 01413 ³ 1 01403 Enable # System 2 Requires Supplements * Disable # Sy stem 2 Requir[...]

Supplements B 5 S ECTION B S UPPLEMEN TS Enable # System 5 Requires Supplements * Disable # System 5 Requires Supplem ents ³ 1 01215 ³ 1 01205 Enable 8711685 Requ ires 5-Digit Su pplement * Disable 8711685 Requires 5-Digit Supplement ³ 1 07613 The scanner will r equire a 5-digit supplem ent to be scanned when an EAN-13 code begins with 8711685. [...]

Supplements B 6 S ECTION B S UPPLEMEN TS Enable Code 128 ‘ ]C1’ Extended Code Format * Disable Code 128 ‘]C1’ Extended Code Format ³ 1 01411 The scanner will tr ansmit a ‘]C1’ at the begin ning of the code 128 portion of the coupon code. ³ 1 01401 The scanner will not transmit a ‘]C1’ at the beginning of th e code 128 portion of t[...]

Supplements B 7 S ECTION B S UPPLEMEN TS 400 msec to Fin d Supplemental ³ 3 01340 The scanner will a llot 400 milliseconds t o “find” an add on after a main U PC/EAN bar code has been scanned. Enable Code ID’s with Supplements * Disable Code ID’s with Supplements ³ 1 01214 ³ 1 01204 Allow 2/5 on 977 Bar Code Allow 2 on 977 Ba r Code ³ 1[...]

Supplements B 8 S ECTION B S UPPLEMEN TS * Beep Once on Supplements Beep twice on Supplements ³ 1 18406 ³ 1 18416 Enable ISBN Check Digit Transmission Disable ISBN Check Digit Transmission ³ 1 01315 This feature is n ot available with al l models. ³ 1 01305[...]

Supplements B 9 S ECTION B S UPPLEMEN TS Enable Bookland t o ISBN Conversion * Disable Bookland to ISBN Conversion ³ 1 01317 This feature is n ot available with al l models. ³ 1 01307 Enable ISBN Re-Formatting * Disable ISBN Re-Formatting ³ 1 01316 This feature is n ot available with al l models. ³ 1 01306[...]

Supplements B 10 S ECTION B S UPPLEMEN TS Enable ISSN Check Digit Transmission * Dis able ISSN Check Digit Transmission ³ 1 15115 ³ 1 15105 Enable ISSN Re-Formatting * Disable ISSN Re-Formatting ³ 1 15116 Transmit a hyphe n with the barcode. ³ 1 15106 Enable 977 to ISSN Conversion * Disable 977 to ISSN Conversion ³ 1 15117 Convert 977 perio di[...]

Supplements B 11 S ECTION B S UPPLEMEN TS Enable Number Sy stem 4 Coupon Code 128 * Disable Number Sy stem 4 Coupon Code 9128 ³ 1 01012 Supports Coupon Code 128 for Number System 4 bar codes. ³ 1 01002 Enable UPC Discard * Disable UPC Discard ³ 1 01013 Supports UPC discard if t he Code 128 portion of the Coupon Code 128 is scanned. ³ 1 01003 Al[...]

[...]

Communications C 1 S ECTION C C OMMUNICATIONS * Enable RS-232 Load Keyboard W edge Defaults ³ 4 15554 The scanner will w ork with RS-232 ± 12V serial output. ³ 9 99994 Scan this before s electing Normal or Stand Alon e Mode. Enable Light Pen/Wand Communication Enable Keyboar d Wedge Emulation ³ 4 15524 Use this option if a scanner is used in pl[...]

Communications C 2 S ECTION C C OMMUNICATIONS Load OCIA Defaults Enable OCIA Output ³ 9 99993 Scan this before s electing Enable OCIA output. ³ 4 15544 Select this option if the communications requirement is an Optically Coupled Interface Adapter (OCIA). This is a docked (by the host) serial interface. Load IBM 46xx Defaults Enable IBM 46xx Commu[...]

Communications C 3 S ECTION C C OMMUNICATIONS Load Low Spee d External USB Defaults † Enable Low Speed USB † ³ 9 99978 † Refer to Section P for full speed USB opt ions. ³ 4155 114 Load Low Spee d Internal USB Defaults † Enable No Communication Mo de ³ 9 99941 ³ 4 15534 Select this option if the scanner does not interf ace with the host [...]

[...]

Scanner Operation D 1 S ECTION D C ONFIGURATION M ODE O PT IONS Allow Configuration Mo de on Power-Up * A llow Configuration Mo de Anytime ³ 1 18117 The scanner can only enter MetroSet ® mode before any bar codes are sca nned. ³ 1 18107 Allow MetroSet ® configuration at any time. Allow Configuration Cod es on Power Up * Allow Configuration Code[...]

Scanner Operation D 2 S ECTION D S CAN B UFFERS * 1 Scan Buffer 2 Scan Buffers ³ 3 18000 The scanner will s can one bar code in the sc an field and not scan a gain until the bar code is remov ed from the scan field f or the duration of the s ame symbol time out. ³ 3 18010 The scanner will s can 2 bar codes in the s can field o ne time each. Thes [...]

Scanner Operation D 3 S ECTION D S CAN B UFFERS 5 Scan Buffers 6 Scan B uffers ³ 3 18040 Same function as 2 Scan Buffers, but 5 bar codes are in the scan fiel d. ³ 3 18050 Same function as 2 Scan Buffers, but 6 bar codes are in the scan fiel d. 7 Scan Buffers 8 Scan B uffers ³ 3 18060 Same function as 2 Scan Buffers, but 7 bar codes are in the s[...]

Scanner Operation D 4 S ECTION D R EDUNDANT S CANS * 0 Redundant Scan s 1 Redundant Scan s ³ 3 01100 Requires 1 good d ecode for a “good scan” . ³ 3 01110 Requires 2 consec utive decodes of the s ame bar code data for a “ good scan”. 2 Redundant Scan s 3 Redundant Scan s ³ 3 01120 Requires 3 consec utive decodes of the s ame bar code dat[...]

Scanner Operation D 5 S ECTION D R EDUNDANT S CANS 6 Redundant Scan s 7 Redundant Scan s ³ 3 01160 Requires 7 consec utive decodes of the s ame bar code data for a “ good scan”. ³ 3 01170 Requires 8 consec utive decodes of the s ame bar code data for a “ good scan”. In-Store Redundancy * Disable In-Store Redundancy ³ 1 01117 Enable redun[...]

Scanner Operation D 6 S ECTION D M ISCELLANEOUS D ECODE F EATURES * Enable Segmente d UPC Decoding Disable Segmente d UPC Decoding ³ 1 01113 Enabling segment ed UPC decoding aids in dec iphering damaged or inco mplete bar codes. ³ 1 01103 Disable this feat ure when bar codes are in good reading conditio n. This will speed up decoding and improve [...]

Scanner Operation D 7 S ECTION D D EPTH OF F IELD A DJUSTMENTS Do not change these settings un less instructed by a Metrologic repr esentative. * Optimize for Low Density Codes † Optimize for High Density Codes † ³ 4 18790 ³ 4187130 Fixed for High Density Codes † Fixed for Medium Density C odes † ³ 4 18700 ³ 4 18710 Fixed for Low Densit[...]

Scanner Operation D 8 S ECTION D S AME S YMBOL T IME O UTS These numbers determine the length of time before a bar code can be rescanned after it is removed from the scan field. Single code fixed settings in msecs of No, 50, 100, 200, 500, 1200 (1.2 sec), 2000 (2.0 sec) and infinite are available. User configurable values can be set in user-configu[...]

Scanner Operation D 9 S ECTION D S AME S YMBOL T IME O UTS Infinite Same Symbol Time Out ~ Variable Same Symbol Time Out ³ 1 18917 The scanner will not repetitively sc an the same bar code. This option overrides the symbol rescan time-outs. ³ 9 18900 Using the Multi-Code Method ( on page x ii ), scan this bar code an d a code byte sequence from S[...]

Scanner Operation D 10 S ECTION D LED O PTIONS Flash Green LED if Rescan Allowed * Do not flash Green LED if Rescan Allowed ³ 1 18313 This indicate s same symbol timeout has ela psed. ³ 1 18303 Reverse LED Functions * Normal LED Functions ³ 1 18312 Red = Laser On Green = Good Read ³ 1 18302 Green = Laser On Red = Good Read * Enable 3 rd LED Dis[...]

Scanner Operation D 11 S ECTION D LED O PTIONS * Las er LED High Intensity Laser LED Low Intensity ³ 2 43100 Laser LED Intensit y is High or Normal. ³ 2 43120 Laser LED is Low Inte nsity This feature is n ot available with al l models. * Sc an LED High Intensity Scan LED Low Intensity ³ 2 43102 Scan LED Intensity is High or Normal. ³ 2 43122 Sc[...]

Scanner Operation D 12 S ECTION D B EEPER O PTIONS * Normal Tone Optional Tone 1 ³ 3 18575 ³ 3 18565 Optional Tone 2 Optional Ton e 3 ³ 3 18555 ³ 3 18545 Optional Tone 4 Optional Ton e 5 ³ 3 18535 ³ 3 18525[...]

Scanner Operation D 13 S ECTION D B EEPER O PTIONS Optional Tone 6 No Beep ³ 3 18515 ³ 3 18505 * Enab le Good Scan Beep Disable Good Scan Beep ³ 1 41903 Enable good scan beep on power up. ³ 1 41913 Disable good sc an beep on power up. * Enable Button Beep Controls Disable Button Beep Controls ³ 1 19701 This feature is n ot available with al l [...]

Scanner Operation D 14 S ECTION D B EEPER O PTIONS Next Beep Tone Next Volume ³ 9 99975 ³ 9 99974 * Loudest Volume 2 nd Loudest Volume ³ 2 18500 ³ 2 18510 3 rd Loudest Volum e No Volume ³ 2 18520 ³ 2 18530[...]

Scanner Operation D 15 S ECTION D B EEPER O PTIONS * Beep Once on Supplements Beep Twice on Supplements ³ 1 18406 ³ 1 18416 Enable Fast Beep * Disable Fast Beep ³ 1 18414 ³ 1 18404[...]

Scanner Operation D 16 S ECTION D B EEPER O PTIONS Beep on BEL Comman d * Ignore BEL Command ³ 1 18417 The scanner beep s when it receives a BEL charac ter from the host. If a number is sent within 20 0 msecs before the BEL c haracter, then the scanner will beep that number of times. ³ 1 18407 Enable Light Pen Toggle During Beep * Disable Light P[...]

Scanner Operation D 17 S ECTION D I NTER - C HARACTER D ATA T RANSMISSION D ELAYS Use these codes to select the amount of delay between sending data characters and “Bar Code” records from the scanner to the host. This helps prevent the scanner from overflowing host input buffers. * 1 msec Inter-Character Delay 10 msec Inter-Character Delay ³ 8[...]

Scanner Operation D 18 S ECTION D I NTER - C HARACTER D ATA T RANSMISSION D ELAYS No Inter-Character Delay ³ 8 18800 I NTER -R ECORD D ATA T RANSMISSION D EL AYS ~ Variable Inter-Record Delay ³ 9 19300 Turn Off Laser During Inter-Record Delay * Leave Laser On During Inter-Record Delay ³ 1 19317 ³ 1 19307[...]

Scanner Operation D 19 S ECTION D C OMMUNICATION T IME O UT O PTIONS Enable Communications Time Outs * Disable Communic ations Time Outs ³ 1 18412 ³ 1 18402 * Beep Before Tran smit Beep After Trans mit ³ 1 18413 Scanner will beep before each label is tr ansmitted. ³ 1 18403 Scanner will beep after each label is transmi tted. ~ Variable Communi [...]

Scanner Operation D 20 S ECTION D C OMMUNICATION T IME O UT O PTIONS Short Communicat ions Time Out (1 sec) Long Communicat ions Time Out (4 secs) ³ 8191200 ³ 8191800 Three Beeps on Time Out * No Bee ps on Time Out ³ 1 18410 ³ 1 18400 Razzberry Tone on Time Out * No Razzberry Tone on Time Out ³ 1 18411 ³ 1 18401[...]

Scanner Operation D 21 S ECTION D H OST S CANNER C OMMANDS Enable “D/E” Disable Command * Disable “D/E” Dis able ³ 1 18015 The scanner will d isable scan ning after it receives and ASCII “D” from the host dev ice. It will enable scanni ng when it rece ives an AS CII “E ”. ³ 1 18005 Do not monitor D/E commands. Enable “Z/R” Ty [...]

Scanner Operation D 22 S ECTION D H OST S CANNER C OMMANDS Motor “On/Off” Using M/O Commands † * Disable “M/O” Commands ³ 1 18213 The scanner will t urn the motor OFF after it receives an ASCII “O” character. T he motor will turn ON after the scanner receives an ASCII “M” character. † † For us e with omni directional scanners[...]

Scanner Operation D 23 S ECTION D H OST S CANNER C OMMANDS Enable S Command * Dis able S Command ³ 1 25610 ³ 1 25600 Enable EM Commands * Dis able EM Commands ³ 1 20610 Enable EM comm and. End of Medium (ctrl Y). The EM command sends a nd ID string then a sc anner status spread over two bytes. ³ 1 20600 Enable SI/SO Command Dis able SI/SO Comma[...]

Scanner Operation D 24 S ECTION D H OST S CANNER C OMMANDS Use DTR Scan Disable * Do not use DTR Scan Disable ³ 1 18115 The scanner will monitor the DTR input to determin e if scanning should be allowed. A +12V “active” level enables decoding. A -12V “inactive” level disables deco ding. ³ 1 18105 Do not monitor the DTR input. Enable Pass [...]

Scanner Operation D 25 S ECTION D H OST S CANNER C OMMANDS Activate on DC2 Character * Do Not Activate on DC2 Character ³ 1 18110 ³ 1 18100 Transmit “NO READ” if DC2 Activated Do Not Transmit “NO READ” if DC2 Activated ³ 1 18111 ³ 1 18101 No Green LED During “NO READ” Xmit * Green LED During “NO READ” Xmit ³ 1 18311 ³ 1 18301[...]

Scanner Operation D 26 S ECTION D P OWER S AVE M ODES Always Power Save Mode † No Power Save Mode † ³ 1 18617 The scanner enter s power save mode immediat ely after power-up and after each bar code sc anned. † † For us e with omnidirectio nal scanners only. ³ 8 18600 The scanner will nev er enter power save mode. † Power Save Mode in 1 [...]

Scanner Operation D 27 S ECTION D P OWER S AVE M ODES Power Save in 20 Minutes † Power Save in 30 Minutes † ³ 8186200 The scanner enter s power save mode if th e scanner remains idle for 2 0 min. † † For use with omni directional scanners only. ³ 8186300 The scanner enter s power save mode if th e scanner remains idle for 3 0 min. † Def[...]

Scanner Operation D 28 S ECTION D P OWER S AVE M ODES Laser OFF Power Save Mode †† Laser Motor OFF Power Save Mode †† ³ 3 19420 The laser turns OFF after a configured period of non-use. This feature is n ot available with al l models. ³ 3 19430 The laser and mot or turns OFF after a configured period of non-use . This feature is n ot avai[...]

Scanner Operation D 29 S ECTION D P OWER S AVE M ODES * Enable Power Save Switch Disable Power Save Switch ³ 1 19700 This feature is n ot available with al l models. ³ 1 19710 This feature is n ot available with al l models. Enable Wake with Switch Only * Enable Wake with IR or Switch ³ 1 19717 Only wake from power sa ve using the multi-f unctio[...]

Scanner Operation D 30 S ECTION D J APANESE D OUBLE F IELD S UPPORT To support Japanes e Double Field Bar Cod es, first make sure y ou have your sc anner configured t o the following sett ings. • Disable Segmented UPC Dec oding • Enable 2 scan b uffers • Disable bar code absence det ection • Enable normal co de selects Then, scan the En abl[...]

Scanner Operation D 31 S ECTION D J APANESE D OUBLE F IELD S UPPORT Upper Code 1 Character 1 Upper Code 1 Character 2 ³ 9 30000 ³ 9 30100 Lower Code 1 Character 1 Lower Code 1 Character 2 ³ 9 30200 ³ 9 30300 Upper Code 2 Character 1 Upper Code 2 Character 2 ³ 9 30400 ³ 9 30500[...]

Scanner Operation D 32 S ECTION D J APANESE D OUBLE F IELD S UPPORT Lower Code 2 Character 1 Lower Code 2 Character 2 ³ 9 30600 ³ 9 30700 Upper Code 3 Character 1 Upper Code 3 Character 2 ³ 9 30800 ³ 9 30900 Lower Code 3 Character 1 Lower Code 3 Character 1 ³ 9 31000 ³ 9 31100[...]

Scanner Operation D 33 S ECTION D J APANESE D OUBLE F IELD S UPPORT Upper Code 4 Character 1 Upper Code 4 Character 2 ³ 9 31200 ³ 9 31300 Lower Code 4 Character 1 Lower Code 4 Character 2 ³ 9 31400 ³ 9 31500[...]

Scanner Operation D 34 S ECTION D J APANESE D OUBLE F IELD S UPPORT Japanese Trial Ti me Enable Code Sele cts ³ 9 38800 Scan the above bar code followe d by the 3 code bytes in Section M th at represent the time out value desire d if in special co de select mode. 1 is equal to 10 0 milliseconds Example: If a 500 millisec ond timeout is desired, sc[...]

Scanner Operation D 35 S ECTION D T EST M ODES Scanability ON * Scanability OFF ³ 1 18017 The scanner will enter scanability tes t mode. Do not enable unless instructed to by a Metrologic representative. ³ 1 18007 Scan Count Mo de ON * Scan Count Mo de OFF ³ 1 18016 The scanner will enter s can count test mode and the scanner’s firmwar e numbe[...]

[...]

Prefixes/Suffixes E 1 S ECTION E C ONFIGURABLE P REFIXES , A LL D ATA Scan the Enter/Exit Configura tion Mode bar code before trying to set this feature. Please refer to the Multi-Code method on page xii. Enter/Exit Configuration Mod e ~ Configurable Prefi x Character #1 ³ 9 99999 ³ 9 03500 A prefix ID can be added and assigned f or data transmis[...]

Prefixes/Suffixes E 2 S ECTION E C ONFIGURABLE P REFIXES , A LL D ATA ~ Configurable Prefix Character #6 ~ Configurable Prefix Character #7 ³ 9 04000 Assigns a 6 th confi gurable prefix character. ³ 9 04100 Assigns a 7 th confi gurable prefix character. ~ Configurable Prefix Character #8 ~ Configurable Prefix Character #9 ³ 9 04200 Assigns a 8 t[...]

Prefixes/Suffixes E 3 S ECTION E C ONFIGURABLE ID C HARACTERS , C ODE S PECIFIC * Use Configurable Code ID Bytes as Prefixes Us e Configurable Code ID Bytes as Suffixes ³ 1 05507 User configured, code specific ID bytes a re transmitted before the data. If using prefixes , user configured suffixe s can not be use d. ³ 1 05517 User configured, code[...]

Prefixes/Suffixes E 4 S ECTION E C ONFIGURABLE ID C HARACTERS , C ODE S PECIFIC ~ Configurable EAN-8 ID † ~ Configura ble EAN-13 ID † ³ 9 05800 † While using the Multi-Code met hod, scan this bar code followed by the 3 code byte bar c odes in Sect ion M that represent a unique ID charac ter to be associated w ith this bar c ode type. (Refer [...]

Prefixes/Suffixes E 5 S ECTION E C ONFIGURABLE ID C HARACTERS , C ODE S PECIFIC ~ Configurable Code 93 ID † ~ Configurable Co de 11 ID † ³ 9 06300 † While using the Multi-Code met hod, scan this bar code followed by the 3 code byte bar c odes in Sect ion M that represent a unique ID charac ter to be associated w ith this bar c ode type. (Ref[...]

Prefixes/Suffixes E 6 S ECTION E C ONFIGURABLE ID C HARACTERS , C ODE S PECIFIC ~ Configurable Standard 2 of 5 ID † ~ Configurable Interleaved 2 of 5 ID † ³ 9 07100 † While using the Multi-Code met hod, scan this bar code followed by the 3 code byte bar c odes in Sect ion M that represent a unique ID charac ter to be associated w ith this ba[...]

Prefixes/Suffixes E 7 S ECTION E C ONFIGURABLE ID C HARAC TERS C ODE S PECIFIC ~ Configurable MSI Plessey ID † ~ Confi gurable UK Plessey ID † ³ 9 06500 † While using the Multi-Code met hod, scan this bar code followed by the 3 code byte bar c odes in Sect ion M that represent a unique ID charac ter to be associated w ith this bar c ode type[...]

Prefixes/Suffixes E 8 S ECTION E S TANDARD P REFIX C HARACTERS Enable STX Prefix * Disable STX Pref ix ³ 1 16615 The scanner will tr ansmit a S tart of T e X t (ASCII 02H) before each bar c ode. ³ 1 16605 Will not transmit a S tart of T e X t (ASCII 02H) before each bar code. Enable Rockford-Thompson Mod e * Disable Rockford- Thompson Mode ³ 1 0[...]

Prefixes/Suffixes E 9 S ECTION E S TANDARD P REFIX C HARACTERS Enable UPC Prefix ID * Disable UPC Prefix ID ³ 1 16617 When enabled, th e scanner will transmit a prefix before any UPC/EAN bar code. The prefixes are a s follows: A (UPC-A), E0 (UPC-E), F (EAN-13), and FF (EAN-8). ³ 1 16607 Do not send prefix ID Characters with UPC/EAN codes. Enable [...]

Prefixes/Suffixes E 10 S ECTION E S TANDARD P REFIX C HARACTERS Enable Nixdorf ID Characters * Disable Nixdorf ID Characters ³ 1 07917 This option transm its code identifiers before e ach bar code for many Siemens/Nixdorf registers . ³ 1 07907 This option will not transmi t Siemens/Nixdorf c ode identifiers. Enable SANYO ID Characters * Disable S[...]

Prefixes/Suffixes E 11 S ECTION E S TANDARD P REFIX C HARACTERS Enable TEC Register Format ID Characters Dis able TEC Register Format ID Characters ³ 1 24710 ³ 1 24700 Enable TEC MA1530 ID Characters Disable TEC MA1530 ID Characters ³ 1 08010 ³ 1 08000 Enable Symbolog y Prefix Disable Symbology Prefix ³ 1 05514 This option adds a symbology des[...]

Prefixes/Suffixes E 12 S ECTION E S TANDARD P REFIX C HARACTERS Enable Manufactu rer ID Prefix * Disable Ma nufacturer ID Prefix ³ 1 05512 Transmits “METROLOGIC” before all bar cod e data to identify the sc anner as a Metrolog ic Scanner. ³ 1 05502 The scanner will not transmit the man ufacturer identi fication st ring. Enable “C” Prefix [...]

Prefixes/Suffixes E 13 S ECTION E S TANDARD P REFIX C HARACTERS Enable Tab Prefix * Disable Tab Prefix ³ 1 16611 The scanner will tr ansmit a TAB (ASCII 09H) before each bar code. ³ 1 16601 The scanner will not transmit a TAB. Enable SNI Beetle Mod e * Disable SNI Beetle Mode ³ 1 16111 ³ 1 16101 Enable Cipher 102 1 IDs * Disable Cipher 1021 IDs[...]

Prefixes/Suffixes E 14 S ECTION E S TANDARD S UFFIX C HARACTERS * Enable CR Suffix Disable CR Suffix ³ 1 16613 The scanner will tr ansmit a C arriage R eturn after each bar code. ³ 1 16603 The scanner will not transmit a C arriag e R eturn after each bar code. * Enable LF Su ffix Disable LF Suffix ³ 1 16612 The scanner will tr ansmit a L ine F e[...]

Prefixes/Suffixes E 15 S ECTION E S TANDARD S UFFIX C HARACTERS Enable ETX Suffix * Disable ETX Suffix ³ 1 16614 The scanner will tr ansmit E nd of T e X t (ASCII 03H) after the bar code data. ³ 1 16604 The scanner will not transmit E nd of T e X t (ASCII 03H). Enable UPC Suffix ID * Disable UPC Suffix ID ³ 1 16616 The scanner will tr ansmit a s[...]

Prefixes/Suffixes E 16 S ECTION E L ONGITUDINAL R EDUNDANC Y C HECK (LRC) Enable Transmit o f LRC Calculation * Disable Trans mit of LCR Calculation ³ 1 07811 The scanner outp uts an LRC check character af ter the bar code. ³ 1 07801 The scanner will not o utput an LRC (check character) after the bar code. * Start LRC on Firs t Byte Start LRC on [...]

Prefixes/Suffixes E 17 S ECTION E C ONFIGURABLE S UFFIXES , A LL D ATA Scan the Enter/Exit Configuration Mode bar code before trying to set this feature. Refer to the Multi-Code Method on page xii. Enter/Exit Configuration Mod e ~ Configurable Suffix Character #1 ³ 9 99999 ³ 9 04500 A suffix ID can be added and assigned f or data transmission. Us[...]

Prefixes/Suffixes E 18 S ECTION E C ONFIGURABLE S UFFIXES , A LL D ATA ~ Configurable Suffix Character #4 † ~ Configurable Suffix Character #5 † ³ 9 04800 Assigns a 4 th confi gurable suffix character. † While using the Multi-Code met hod, scan this bar code followed by the 3 code byte bar c odes in Sect ion M that represents the desired cha[...]

Prefixes/Suffixes E 19 S ECTION E C ONFIGURABLE S UFFIXES , A LL D ATA ~ Configurable Suffix Character #8 † ~ Configurable Suffix Character #9 † ³ 9 05200 Assigns a 8 th confi gurable suffix character. ³ 9 05300 Assigns a 9 th confi gurable suffix character. ~ Configurable Suffix Character #10 † ³ 9 05400 Assigns a 10 th con figurable suff[...]

Prefixes/Suffixes E 20 S ECTION E S PECIAL F ORMATS Enable SINEKO Mode * Disable SINEKO Mode ³ 1 07914 ³ 1 07904 Enable Newcode Forma tting Mode A * Disable N ewcode Formatting M ode A ³ 1 16711 ³ 1 16701 Enable Newcode Forma tting Mode B * Disable Newcode Formatting M ode B ³ 1 16710 ³ 1 16700[...]

Prefixes/Suffixes E 21 S ECTION E C HARACTER R EPLACEMENTS To replace a character: 1. Scan the Enter/Exit Configura tion Mode bar code (located on page xii, at t he front of this guide). 2. Scan the Character to Replac e Code (shown belo w). 3. Scan the ASCII Code Byte value of the chara cter you wish to replace (refer to the ASCII reference table [...]

[...]

Code Formatting F 1 S ECTION F UPC/EAN * Transmit UPC-A Check Digit Do not Transmit UPC-A Check Digit ³ 1 07517 ³ 1 07507 Transmit UPC-E Check Digit * Do Not Transmit UPC-E Check Digit ³ 1 07516 ³ 1 07506 Expand UPC-E to 12 Digits * Do Not Expa nd UPC-E To 12 Digits ³ 1 07515 Expand UPC-E bar codes to the 12 digit equivalent , UPC-A bar codes.[...]

Code Formatting F 2 S ECTION F UPC/EAN Convert UPC-A to EAN-13 * Do Not Convert UPC-A to EAN-13 ³ 1 07514 The scanner conv erts UPC-A to EAN-13 by transmitting a le ading zero before the bar c ode. ³ 1 07504 The scanner will not c onvert UPC-A to EAN-13. Transmit Lead Zer o on UPC-E Do Not Transmit Lead Zero on UPC-E ³ 1 07513 This option will t[...]

Code Formatting F 3 S ECTION F UPC/EAN * Transmit UPC-A Number System Do Not Transmit UPC-A Number System ³ 1 07511 ³ 1 07501 Metrologic strongly discourages using this feature. Duplicate numbers may result in the database. * Transmit UPC-A MFR # Do Not Transmit UPC-A MFR # ³ 1 07611 ³ 1 07601 * Transmit UPC-A ITEM # Do Not Transmit UPC-A ITEM [...]

Code Formatting F 4 S ECTION F UPC/EAN * Transmit EAN-8 Check Digit Do Not Transmit EAN-8 Check Digit ³ 1 07910 ³ 1 07900 * Transmit EAN-13 Check Digit Do Not Transmit EAN-13 Check Digit ³ 1 07912 ³ 1 07902 GTIN-14 Format No GTIN-14 Format ³ 1 07510 This feature is n ot available with al l models. ³ 1 07500[...]

Code Formatting F 5 S ECTION F C ODABAR Transmit Codabar Start/Stop Characters * Do Not Transmit Codabar Start/Stop ³ 1 07717 Transmits Codabar’s start/stop characters before and after each bar code. ³ 1 07707 Will not transmit Codabar’s start/stop characte rs before and after each bar code. Convert Codabar Start/Stop Characters to Lowerc ase[...]

Code Formatting F 6 S ECTION F C ODABAR Enable CLSI Editing ³ 1 07716 CLSI type editing will be done before the inf ormation is transmitted to the host. This option will only work with 14 digit Codabar type leng ths. * Do Not Enable CLSI Editing ³ 1 07706 This option will not perf orm CLSI type editing before the information is tran smitted to th[...]

Code Formatting F 7 S ECTION F C ODE 39 Enable MOD 43 Check on Code 39 * Disable MOD 43 Check on Code 39 ³ 1 00213 The scanner will o nly scan Code 39 bar codes that have a valid M odulo 43 Check Digit. ³ 1 00203 The scanner will not tes t Code 39 bar code s for a Modulo 43 Check Digit. Transmit Mod 43 Check Digit on Code 39 * Do Not Tra nsmit Mo[...]

Code Formatting F 8 S ECTION F C ODE 39 Transmit Code 39 Start/St op Characters ³ 1 07710 The scanner trans mits Code 39’s start/stop cha racters before and after each bar c ode. * Do Not Transmit Code 39 Start/Stop Characters ³ 1 07700 The scanner will not tra nsmit Code 39’s start/s top characters before and aft er each bar code.[...]

Code Formatting F 9 S ECTION F C ODE 11 A ND T ELEPEN Transmit Code 11 Check Digit * Do Not Transmit Code 11 Check Digit ³ 1 07713 The scanner will tr ansmit Code 11 check characters when used with th e Enable Code 11 feature in Section A. ³ 1 07703 The scanner will not transmit Code 11 check characters. Enable Convert Telepen ^L to E * Disable C[...]

Code Formatting F 10 S ECTION F P LESSEY Transmit UK Plessey Check Dig it * Do Not Transmit UK Plessey Check Dig it ³ 1 07816 The scanner will tr ansmit UK Plessey Check Dig it characters when us ed with the Enable UK Ples sey feature in Section A. ³ 1 07806 Will not transmit UK Plessey Check Digit chara cters. Enable UK Plessey Special For mat D[...]

Code Formatting F 11 S ECTION F P LESSEY * No MSI Plessey Check Digit ³ 2 00704 The scanner will not tes t MSI Plessey bar codes for a check digit. Enable MSI Plessey M OD 10/10 Check Digit * Enable MSI Plessey MOD 10 Check Digit ³ 2 00734 The scanner will t est MSI Plessey bar co des for a double Modulo 10 chec k digit. ³ 2 00724 The scanner wi[...]

Code Formatting F 12 S ECTION F 2 OF 5 Enable Mod 10 Check on ITF * Disable MOD 10 Check on ITF ³ 1 00310 The scanner will o nly scan Interleaved 2 of 5 (ITF) bar codes that hav e a Modulo 10 check digit. ³ 1 00300 The scanner will not tes t Interleaved 2 of 5 (ITF) bar codes for a Modu lo 10 check digit. Transmit Mod 10 Check Digit on ITF * Do N[...]

RS-232 G 1 S ECTION G E NABLE RS-232 M ODE * Enable RS-232 Mode ³ 4 15554 When enabled the scanner will work with RS-232 ±12V serial output.[...]

RS-232 G 2 S ECTION G P ARITY F EA TURES No Parity A parity bit is an extra data bit used to help catch data transmission errors. The scanner’s parity must match the host’s parity. ³ 3 16045 Odd Parity * Space Parity ³ 3 16005 Select Odd Parity to set the parity bit to either 1 or 0 to ensure an odd number of bits are 1’s. ³ 3 16015 Select[...]

RS-232 G 3 S ECTION G B AUD R AT ES 115200 BAUD Rate A “Baud” or “Baud Rate” is the speed at which data is transmitted. Select a Baud for the scanner that matches the host device. ³ 4158100 57600 BAUD Rate 38400 BAUD Rate ³ 4 15890 ³ 4 15880 19200 BAUD Rate 14400 BAUD Rate ³ 4 15870 ³ 4 15860[...]

RS-232 G 4 S ECTION G B AUD R AT ES * 9600 BAUD Rate 4800 BAUD Rate ³ 4 15850 ³ 4 15840 2400 BAUD Rate 120 0 BAUD Rate ³ 4 15830 ³ 4 15820 600 BAUD Rate 300 BAUD Rate ³ 4 15810 ³ 4 15800[...]

RS-232 G 5 S ECTION G D ATA /S TOP B ITS * 7 Data Bits 8 Data Bits ³ 1 16003 Number of data b its transmitted for eac h character. ³ 1 16013 1 Stop Bit * 2 Stop Bits ³ 1 16014 ³ 1 16004[...]

RS-232 G 6 S ECTION G H ARDWARE H ANDSHAKING Enable RTS/CTS Handshaking * Disable RTS/CTS Handshaking ³ 1 15816 O utput a R equest to S end (RTS) signal and wait f or a C lear T o S end (CTS) signal before transmit ting data. ³ 1 15806 Do not use RTS/CTS handshaking. * Character RTS/CTS Message RTS/CTS ³ 1 15815 Activate/Deactivate RTS signal fo[...]

RS-232 G 7 S ECTION G H ARDWA RE H ANDSHAK ING Invert CTS Polarity (RSV2) * Standard CTS Polarity ³ 1 24511 +12V = Inactive, do no t send -12V = Active, OK to send ³ 1 24501 -12V = Inactive, do no t send +12V = Active, OK to send Activate RTS, Do Not wait for CTS (RSV3) * Activate RTS, Wait for CTS ³ 1 24512 Activate RTS for transmission but d o[...]

RS-232 G 8 S ECTION G H ARDWA RE H ANDSHAK ING CTS Scan Transmit * No CTS Scan Tr ansmit ³ 1 20417 The CTS line is us ed to allow a decoded bar code to be transmitted. Use r eserved code 4 to ensure 1 bar code per CTS. This will prev ent the scanner from gathering data until the CTS sign al has been retracted. This feature is n ot available with a[...]

RS-232 G 9 S ECTION G S OFTWARE H ANDSHAKIN G Enable XON/XOFF Handshaking * Disable XON/XOFF Handshaking ³ 1 15914 The scanner will st op transmission when ever an XOFF (ASCII 13H) is received. Transmi ssion will resume after an XON (ASCII 11H) is received. ³ 1 15904 The scanner will not tes t for XON/XOFF. Enable ACK/NAK * Disable ACK/NAK ³ 1 1[...]

RS-232 G 10 S ECTION G S OFTWARE H ANDSHAKIN G Enable O/N Handshaking Disable O/N Handshaking ³ 1 15912 ACK/NAK handshaking (page G 9) must be en abled for this feature to work. ³ 1 15902 Support BEL/CAN in ACK/NAK * Ignore BEL/CAN in ACK/NAK ³ 1 15911 When BEL (07H) is rec eived, the scanner bee ps 3 times and exits the comm unications loo p. I[...]

RS-232 G 11 S ECTION G S OFTWARE H ANDSHAKIN G Enable XON/XOFF Scan Inhibit On * Dis able XON/XOFF Scan Inhibit Off ³ 1 16011 This feature is n ot available with al l models. ³ 1 16001 This feature is n ot available with al l models. Enable 5 Retries o n ACK/NAK Time Out * Disable 5 Retr ies on ACK/NAK Time Out ³ 1 18013 Allow up to 5 NAK retran[...]

RS-232 G 12 S ECTION G M ISCELLANEOUS Enable French PC Term * Disable French P C Term ³ 1 16110 The scanner trans mits PC type make/break s can codes instead of ASCII data characters. The s can codes match a WYSE French PC Terminal Emulatio n. ³ 1 16100 Do not transmit in French PC Term Mode. Enable USA Wyse PC Disable USA Wyse PC ³ 1 16117 Enab[...]

Keyboard H 1 S ECTION H E NABLE K EYBOARD E MULATION Load Keyboard W edge Defaults ³ 9 99994 Loads default s ettings for keyboard wedge mod e. Enable Stand-Alone Key board Emulation * Enable Keyboar d Wedge Emulation ³ 5155153 Use this with speci al stand- alone models that are not cabled for an external keyboard. When t he Stand- Alone Mode is e[...]

Keyboard H 2 S ECTION H C OUNTRY /S CAN C ODE T ABLE S ELECTS * USA Keyboard Switzerland Keybo ard ³ 4 16260 Enable USA Keyboard. ³ 4 16280 Enable Swiss Keyboar d Spain Keyboard Italy Keyboard ³ 4 16250 Enable Spanish K eyboard ³ 4 16240 Enable Italian Key board Germany Keyboard Franc e Keyboard ³ 4 16230 Enable German Key board ³ 4 16220 Ena[...]

Keyboard H 3 S ECTION H C OUNTRY /S CAN C ODE T ABLE S ELECTS UK Keyboard Belgium Keyboard ³ 4 16210 Enable UK Keyboard. ³ 4 16200 Enable Belgium K eyboard Japanese Keybo ard IBM 4700 Financial Keyboard ³ 4162100 Enable Japanes e Keyboard ³ 4 16270 Enable IBM 4700 Financial Keyboard Sweden/Finland Key board ³ 4 16290 Enable Sweden/Finland Keyb[...]

Keyboard H 4 S ECTION H K EYBOARD /S YS TEM T YPE * AT Keyboard XT Keyboard ³ 2 16215 If using an AT comput er, scan the above bar code. (Includes IBM PS/2 an d compatible mod els 50, 55, 60, 80) ³ 2 16205 If using an XT comput er, scan the above bar code. PS/2 Keyboard Terminal KB Emulatio n ³ 2 16225 Scan the above co de for PS/2 computer. (In[...]

Keyboard H 5 S ECTION H S PECIAL K EYBOARD F EATURES Transmit Make Code Only * Transmit Make/Break Code ³ 1 16311 Do not scan unless instructed by a Metrologic representative. ³ 1 16301 Do not scan unless instructed by a Metrologic representative. Do Not Transmit F0H Break Code * Transmit F0H Break Code ³ 1 16300 The scanner will not transmit th[...]

Keyboard H 6 S ECTION H S PECIAL K EYBOARD F EATURES Enable Alt Mode * Disable Alt Mode ³ 1 16217 The scanner will d uplicate the following key board sequence: Hold down ALT key and Type decimal n umber that corresponds to the appropriate chara cter. ³ 1 16207 Caution: If the ho st software applicatio n uses the right ALT key as a “Hot” k ey,[...]

Keyboard H 7 S ECTION H S PECIAL K EYBOARD F EATURES Enable Caps Lock (XT) * Disable Caps Lock (XT) ³ 1 16214 ³ 1 16204 The Caps Lock feature is not supported. Send Numbers as Keypad Data * Send Numbers as Normal Data ³ 1 16316 All data is sent as if it has been entered on a keypad. ³ 1 16306 Enable Reserved Feature * Disable Reserved Feature ?[...]

Keyboard H 8 S ECTION H S PECIAL K EYBOARD F EATURES * Use Extended ASCII to Send Extended Key Codes Use Extended ASCII Characters as Extend ed ASCII ³ 1 16303 Use extended ASCII characters to send PC keyboard keys s uch as F1, F2, etc…See section M for details. ³ 1 16313 Transmit extended ASCII codes via ALT m ode. * Character KB Inhibit Messa[...]

Keyboard H 9 S ECTION H I NTER -S CAN C ODE D ELAYS Inter-Scan Code Delay 800 Microseconds Inter-Scan Cod e Delay 7.5 msec ³ 8 16580 The time specifi ed represents the amount of tim e between individual 9 bi t-scan codes. This parameter m ay need to be adjus ted for operation with certain PC keyboard BIOS. ³ 8165750 The time specifi ed represents[...]

Keyboard H 10 S ECTION H C ONTROL S ETS In general, standard bar code symbologies will only encode the ASCII character set. Function keys, arrow keys and many other “extended” keys on an IBM compatible keyboard do not translate to ASCII characters. One method of “bar coding” the extended keys is to substitute the extended key codes when a s[...]

Keyboard H 11 S ECTION H C ONTROL S ET #1 ASCII (HEX) ASCII Control Extended Ke y 00H Null Numeric Keypad 01H SOH Num Lock 02H STX Down 03H ETX Numeric Keypad 04H EOT Insert 05H ENQ Delete 06H ACK System Request 07H BEL  08H BS  09H TAB Tab 0AH LF Caps Lock 0BH VT Shift Tab 0CH FF Alt 0DH CR Enter 0EH SO Control 0FH SI Up Arrow 10H DLE F1 11H[...]

Keyboard H 12 S ECTION H 3151 T ERMINAL K EYBOARD * 3151 Terminal K eyboard ³ 3 16400[...]

OCIA I 1 S ECTION I OCIA Load OCIA Defaults Enable OCIA ³ 9 99993 ³ 4 15544 Select this option if communications require OCIA ( O ptically C oupled I nterface A dapter). This serial interfac e is clocked by the host. Enable DTS/Siemens * Enable DTS/Nix dorf ³ 2 17706 ³ 2 17716 Enable NCR-S Enable NCR-F ³ 2 17736 ³ 2 17726[...]

[...]

Light Pen/Laser Emulation J 1 S ECTION J L IGHT P EN Enable Light Pen Mode ³ 4 15524 Select this option if the scanner will be us ed in place of a light pen. It provides light p en emulation of each bar code s canned. * Bars High Spaces High ³ 1 16917 ³ 1 16907 Transmit Code 39 * Transmit as Scanned ³ 1 16916 All bar codes will be decoded then [...]

Light Pen/Laser Emulation J 2 S ECTION J L IGHT P EN /S ET N ARROW E LEMENT B ORDER Poll Light Pen S ource * Do Not Poll Light Pen S ource ³ 1 16915 The scanner waits for a n active source volt age before transmitting data. ³ 1 16905 The scanner will not wai t for an active source v oltage before transmit ting data. Enable Light Pen a Extra Toggl[...]

Light Pen/Laser Emulation J 3 S ECTION J S ET N ARROW E LEMENT W IDTH /L ASER E MULATION * 1 ms Narrow Element Width 60 µs Narrow Element Width ³ 81681630 This option allows the transmission of Light/Pen Wand emulation a 1 ms narrow element width. ³ 8168100 This transmits at 60 µs narrow element width. 100 µs Narrow Element Width 500 µs Narro[...]

[...]

IBM 46xx Configuration K 1 S ECTION K IBM 46 XX C ONFIGUR ATION /IBM P ORTS Load IBM 46xx Defaults Enable IBM 46xx Communication ³ 9 99995 Load default form at settings for IBM 46xx systems. ³ 4 15504 Select this option for IBM 46xx SIOC/RS485 communication. Not all scanners support this interfac e. The correct interface board is requir ed. IBM P[...]

IBM 46xx Configuration K 2 S ECTION K IBM R ESER VE C ODES IBM Reserve #1 IBM Reserve # 2 ³ 3 17200 ³ 3 17210 IBM Reserve #3 ³ 3 17220 IBM Reserve #5 ³ 3 17240[...]

Code Bytes M 1 S ECTION M C ODE B YT E U SAGE User configurable prefixes, symbol length and other features that use these code bytes for configuration, require that the scanner be in configuration mode. Scan the Enter/Exit Configuration Mode bar code before starting t he configuration cycle. Single code configuration mode does not work for these mu[...]

Code Bytes M 2 S ECTION M C ODE B YTE S 0-5 Code Byte 0 Code Byte 1 ³0 ³1 Code Byte 2 Code Byte 3 ³2 ³3 Code Byte 4 Code Byte 5 ³4 ³5[...]

Code Bytes M 3 S ECTION M C ODE B YTE S 6-9 Code Byte 6 Code Byte 7 ³6 ³7 Code Byte 8 Code Byte 9 ³8 ³9[...]

Code Bytes M 4 S ECTION M R ESERVED C ODES ~ Enable Reserved Code ³ 9 99988 Contact a Metrolo gic customer s ervice representative for additional deta ils on this feature. ~ Disable Reserved Code ³ 9 99987[...]

Code Bytes M 5 S ECTION M C ODE B YTE /C ODE T YPE T ABLE C ODE B YTE C ODE T YPES 004 UPC-A 002 UPC-E 003 EAN-8 005 EAN-13 080 Code 39 081 Codabar 082 Interleaved 2 of 5 083 Code 128 084 Code 93 091 MSI Plessey 092 Code 11 093 Airline 2 of 5 (15 digits) 094 Matrix 2 of 5 095 Telepen 096 UK Plessey 098 Standard 2 of 5 097 Airline (13 digits) 099 TR[...]

Code Bytes M 6 S ECTION M ASCII R EF ERENCE T ABLE HEX V ALUE D ECIMAL V ALUE / C ODE B YTE V ALUE C HARACTER C ONTROL K EYBOARD E QUIVALENT 00 000 NUL @ 01 001 SOH A 02 002 STX B 03 003 ETX C 04 004 EOT D 05 005 ENQ E 06 006 ACK F 07 007 BEL G 08 008 BS H 09 009 HT I 0A 010 LF J 0B 011 VT K 0C 012 FF L 0D 013 CR M 0E 014 SO N 0F 015 SI O 10 016 DL[...]

Code Bytes M 7 S ECTION M ASCII R EF ERENCE T ABLE HEX V ALUE D ECIMAL V ALUE / C ODE B YTE V ALUE C HARACTER C ONTROL K EYBOARD E QUIVALENT 1B 027 ESC [ 1C 028 FS 1D 029 GS ^ 1E 030 RS _ 1F 031 US 20 032 SP space, blank 21 033 ! 22 034 “ 23 035 # 24 036 $ 25 037 % 26 038 & 27 039 ‘ apostrophe 28 040 ( 29 041 ) 2A 042 * 2B 043 + 2C 044 , [...]

Code Bytes M 8 S ECTION M ASCII R EF ERENCE T ABLE HEX V ALUE D ECIMAL V ALUE / C ODE B YTE V ALUE C HARACTER C ONTROL K EYBOARD E QUIVALENT 36 054 6 37 055 7 38 056 8 39 057 9 3A 058 : 3B 059 ; 3C 060 < less than 3D 061 = 3E 062 > greater than 3F 063 ? 40 064 @ shift P 41 065 A 42 066 B 43 067 C 44 068 D 45 069 E 46 070 F 47 071 G 48 072 H 4[...]

Code Bytes M 9 S ECTION M ASCII R EF ERENCE T ABLE HEX V ALUE D ECIMAL V ALUE / C ODE B YTE V ALUE C HARACTER C ONTROL K EYBOARD E QUIVALENT 4F 079 O letter O 50 080 P 51 081 Q 52 082 R 53 083 S 54 084 T 55 085 U 56 086 V 57 087 W 58 088 X 59 089 Y 5A 090 Z 5B 091 [ shift K 5C 092 shift L 5D 093 ] shift M 5E 094 ^  , shift N 5F 095 _  , shi[...]

Code Bytes M 10 S ECTION M ASCII R EF ERENCE T ABLE HEX V ALUE D ECIMAL V ALUE / C ODE B YTE V ALUE C HARACTER C ONTROL K EYBOARD E QUIVALENT 6A 106 j 6B 107 k 6C 108 l 6D 109 m 6E 110 n 6F 111 o 70 112 p 71 113 q 72 114 r 73 115 s 74 116 t 75 117 u 76 118 v 77 119 w 78 120 x 79 121 y 7A 122 z 7B 123 { 7C 124 | vertical slash 7D 125 } alt mode 7E 1[...]

Code Bytes M 11 S ECTION M E XTEND ED K EY C ODE R E FERENCE T ABLE K EY A T S CAN C ODE PS2 S CAN C ODE 3151 P REFIX /S UFFIX V ALUE H EX = D ECIMAL  75H 48H 63H 80H = 128  72H 50H 60H 81H = 129  74H 4DH 6AH 82H = 130  6BH 4BH 61H 83H = 131 Insert 70H 52H 67H 84H = 132 Delete 71H 53H 64H 85H = 133 Home 6CH 47H 6EH 86H = 134 End 69H 4FH[...]

Code Bytes M 12 S ECTION M E XTEND ED K EY C ODE R E FERENCE T ABLE K EY A T S CAN C ODE PS2 S CAN C ODE 3151 P REFIX /S UFFIX V ALUE H EX = D ECIMAL Numeric - 7BH 4AH 7CH 9DH = 157 Numeric * 7CH 37H 00H 9EH = 158 Caps Lock 58H 3AH 14H 9FH = 159 Num Lock 77H 45H 00H A0H = 160 Left ALT 11H 38H 00H A1H = 161 Left CTRL 14H 1DH 11H A2H = 162 Left Shift[...]

Miscellaneous Features N 1 S ECTION N C USTOM D EFAULTS Metrologic manufactures several scanners for OEM applications. These scanners may use a different set of defaults than the standard Metrologic factory defaults. Scanning the following bar codes will restore the default factory settings. Enable Factory Defaul ts ³ 8 46600 Scan this code f ollo[...]

Miscellaneous Features N 2 S ECTION N C USTOM D EFAULTS Ruby Verifone Defaults RCH ³ 84661280 Scan this code f ollowed by the “Recall Defau lts” code to enable and loa d Ruby Verifone Defaults. ³ 8 46610 Scan this code f ollowed by the “Recall Defaults ” code to enable and load RCH Defaults. Sanyo Gilbarc o ³ 8466020 Scan this code f oll[...]

Miscellaneous Features N 3 S ECTION N C USTOM D EFAULTS German Post Defaults Wincor Nixdorf Defaul ts ³ 84660090 Scan this code f ollowed by the “Recall Defau lts” code to enable and loa d German Post Defaults. ³ 84 660140 Scan this code f ollowed by the “Recall Defau lts” code to enable and loa d Wincor Nixdorf Defaults. Quantum Pharmac [...]

Miscellaneous Features N 4 S ECTION N C USTOM D EFAULTS Custom 21 Default s Cus tom 22 Defaults ³ 84660210 Scan this code f ollowed by the “Recall Defau lts” code to enable and loa d Custom 21 Defaults. ³ 84 660220 Scan this code f ollowed by the “Recall Defau lts” code to enable and loa d Custom 22 Defaults. Custom 23 Default s ³ 846602[...]

Miscellaneous Features N 5 S ECTION N S ERIAL C ONFIGUR ATION M ODE For Serial Configuratio n Mode, all comma nds must be f ramed by an STX (02 Hex ) and ETX (03 Hex). To recall defaults: 1. Transmit <STX>9999 99<ETX> through the Seri al Port. This will put the scanner in serial c onfiguration m ode. Scanning will be suspende d and the [...]

[...]

Auxiliary Port Controls O 1 S ECTION O D ISABLE A UXILIARY P ORT * Disable AUX Port ³ 4 37300 AUX P ORT AND S ECONDARY D EVIC E D ATA F ORMATS The following se ction includes features that are not available with all Metrologic scanner models. Please contact a customer service representative for additional information and technical assistance. When[...]

Auxiliary Port Controls O 2 S ECTION O AUX P ORT AND S ECONDARY D EVIC E D ATA F ORMATS Step 2 : Then scan the following bar codes, in order, to configure the secondary scanner. 1. Enable AUX Output 2. Secondary Scanner Data Format ³ 1 24817 ³ 4 37530 3. Enable Comm Timeouts 4. Turn OFF Auxiliary Scanner’s Beeper (Optional) ³ 1 18412 ³ 3 1850[...]

Auxiliary Port Controls O 3 S ECTION O AUX P ORT AND S ECONDARY D EVIC E D ATA F ORMATS The following se ction includes features that are not available with all Metrologic scanner models. Please contact a customer service representative for additional information and technical assistance. When using a non-Metrologic RS -232 device as a secondary: S[...]

Auxiliary Port Controls O 4 S ECTION O A DDITIONAL A UXILIARY P ORT D ATA F ORMATS The auxiliary input port’s data format must match the main output format of the secondary device. Enable AUX Port with UPC Supplemental D ata Format Enable AUX Port with Code Select Data Format ³ 4 37340 ³ 4 37350 Enable AUX Port with Tech 7, 8 Data Format Enable[...]

Auxiliary Port Controls O 5 S ECTION O A DDITIONAL A UXILIARY P ORT D ATA F ORMATS Enable AUX Port with Stratos Decode Data Format ³ 4 37320 A UXILIARY P ORT B AUD R ATES AUX 115200 Baud Rate AUX 57600 Baud Rate ³ 4370100 ³ 4 37090 AUX 38400 Baud Rate AUX 19200 Baud Rate ³ 4 37080 ³ 4 37070[...]

Auxiliary Port Controls O 6 S ECTION O A UXILIARY P ORT B AUD R ATES AUX 14400 Baud Rate AUX 9600 Baud Rate ³ 4 37060 ³ 4 37050 AUX 4800 Baud Rate AUX 2400 Ba ud Rate ³ 4 37040 ³ 4 37030 AUX 1200 Baud Rate AUX 600 Bau d Rate ³ 4 37020 ³ 4 37010[...]

Auxiliary Port Controls O 7 S ECTION O A UXILIARY P ORT B AUD R ATES AUX 300 Baud Rate ³ 4 37000 A UXILIARY P ORT P ARITY AUX No Parity ³ 3 37245 AUX Mark Parity * AUX Space Parity ³ 3 37235 ³ 3 37215[...]

Auxiliary Port Controls O 8 S ECTION O A UXILIARY P ORT P ARITY AUX Even Parity AUX Odd Parity ³ 3 37225 ³ 3 37205 A UXILIARY P ORT S TOP B ITS /D ATA B ITS AUX 1 Stop Bit * AUX 2 Stop Bits ³ 1 37214 ³ 1 37204 * AUX 7 Data Bits AUX 8 Data Bits ³ 1 37203 ³ 1 37213[...]

Auxiliary Port Controls O 9 S ECTION O A UXILIARY RTS/CT S AND M ODE 7 * Enable AUX RTS/CTS Handshaking Disable AUX RTS/CTS Handshaking ³ 1 37016 ³ 1 37006 Message AUX RTS/CTS * Character AUX R TS/CTS ³ 1 37005 ³ 1 37015 Enable AUX Port Mode 7 Disable AUX P ort Mode 7 ³ 4 37370 Mode 7 enables reception of prefix and suffix c odes when AUX port[...]

Auxiliary Port Controls O 10 S ECTION O A UXILIARY D/E, F/L, AND M/O Enable AUX “D/E” Commands * Disable AUX “D/E” Commands ³ 1 37117 ³ 1 37107 Enable AUX “F/L” Commands * Disable AUX “F/L” Commands ³ 1 37116 ³ 1 37106 Enable AUX “M/O” Commands * Disable AUX “M/O” C omma nds ³ 1 37115 ³ 1 37105[...]

Auxiliary Port Controls O 11 S ECTION O A UXILIARY XON/XOFF AND ACK/ NAK * Enable AUX XON/ XOFF Handshaking Disable AUX XON/XOFF Handshaking ³ 1 37114 ³ 1 37104 * Enable AUX ACK/NAK Commands Disable AUX ACK/NAK Commands ³ 1 37113 ³ 1 37103[...]

Auxiliary Port Controls O 12 S ECTION O A UXILIARY CTS AND RTS P OLARITY * Normal AUX CTS Polarity Flip AUX CTS Polarity ³ 1 37307 ³ 1 37317 * Normal AUX RTS Polarity Flip AUX RTS Polarity ³ 1 37306 ³ 1 37316 A UXILIARY S AME S YMBOL T IMEOUT * AUX has Same Symbol Tim eout No AUX Same Symbol Tim eout ³ 1 37304 This feature sk ips the same symb[...]

Auxiliary Port Controls O 13 S ECTION O M AIN O UTPUT P ORT A UXILIARY D ATA F ORMATS When a scanner is used as a secondary scanner to another scanner’s auxiliary input, the output data can be in one of the following formats. Reserve Code 32 ³ 1 24817 This is a quick method for setting reserve Code 32 i n the secondary sc anner using HoloTrak De[...]

Auxiliary Port Controls O 14 S ECTION O M AIN O UTPUT P ORT A UXILIARY D ATA F ORMATS TECH 7 & 8 Output AUX Data Format Reserved 1 Output AUX Data Format ³ 4 37560 ³ 4 37590 Reserved 2 Output AUX Data Format Beetl e Mode AUX Data Format ³ 4 37580 ³ 4 37570[...]

Auxiliary Port Controls O 15 S ECTION O I NTER -C HARACTER D ELAYS No AUX Port Inter-Character Delays * 1 msec AUX Port Inter-Character Delay ³ 8 37600 ³ 8 37610 10 msec AUX Port Inter-Character Delay 25 msec AUX Port Inter-Character Delay ³ 8376100 ³ 8376250 ~ Variable AUX Port Inter-Character Delay ³ 9 37600 The Delay between charac ters bei[...]

Auxiliary Port Controls O 16 S ECTION O A UXILIARY P ORT C ONTROLS Prevent Beep From AUX * Allow Beep from A UX ³ 8 37600 Prevent the main scanner from beeping whe n the barcode comes fr om the AUX port. This is the opposite of not beeping the AUX and letting t he main scanner beep as v erification of the barcode sen t. ³ 8 37610 Allow the main s[...]

USB P 1 S ECTION P USB Enable Full Speed USB ³ 4155124 Load Integrate d Full Speed USB IBM/OEM Defaults ³ 9 99970[...]

USB P 2 S ECTION P USB The following cod es can be used if the Loa d Integrated Full Spee d USB IBM/OEM Defaults bar code has not been scanned. Enable USB IBM ID * Disable USB IBM ID ³ 1 17817 ³ 1 17807 * Enha nced Code I Ds Legacy Code IDs ³ 1 17804 ³ 1 17814 Reserved * Normal USB Out ³ 1 17816 ³ 1 17806[...]

USB P 3 S ECTION P USB The following cod es can be used if the Loa d Integrated Full Spee d USB IBM/OEM Defaults bar code has not been scanned. IBM OEM Scanner 4A00h Flatbed IBM OEM Scanner 4B00h Handheld ³ 3 16410 Full speed USB only. ³ 3 16430 Full speed USB only. 4A00h/6E00h Tabletop Scanner/ Scale * Enable USB K eyboard Emulation Mode ³ 3 16[...]

USB P 4 S ECTION P USB Enable Low Speed USB Enable Low Speed USB POS Defaults ³ 4155 114 ³ 84 660180 Load Low Spee d External USB Defaults Load L ow Speed Internal USB Keyboard Defaults ³ 9 99978 ³ 9 99941 For units labeled Low Speed (LS) USB. Load Full Speed K eyboard Internal USB Defaults ³ 9 99940 For units labeled Full Speed (FS) USB.[...]

IS3480 / MS3580 / MS3780 R 1 S ECTION R IS3480 / MS3580 / MS3780 The following bar codes are spec ific to the IS 3480, MS358 0 and the MS3780 unless oth erwise noted. Button Modes * Butto n Click Patter n Switching Mode Button Hol d Pattern Switching Mode ³ 1 23806 ³ 1 23816 Button Click Delay 15 Second Time Out † 10 Seco nd Time Out † ³ 523[...]

IS3480 / MS3580 / MS3780 R 2 S ECTION R IS3480 / MS3580 / MS3780 The following bar codes are spec ific to the IS 3480, MS358 0 and the MS3 780 (in-stand) unless otherwise noted. Primary Scan Patterns Secondary Scan Patterns * Primary Omni Secondary Omni ³ 9 99947 This bar code se ts the primary pattern to all scan lines on for omn idirectional rea[...]

IS3480 / MS3580 / MS3780 R 3 S ECTION R MS3780 The following bar codes are spec ific to the MS37 80 (out-of-stan d) unless otherwis e noted. Primary Scan Patterns Secondary Scan Patterns * Primary Omni, Out-of-Stand Secondary Omni, Out-of-Sta nd ³ 9 99937 This bar code se ts the primary pattern to all scan lines on for omn idirectional reading. ³[...]

IS3480 / MS3580 / MS3780 R 4 S ECTION R IS3480 / MS3580 / MS3780 The following bar codes are spec ific to the IS 3480, MS358 0 and the MS3780 unless oth erwise noted. Sweet Spot Mode Enable Sweet Spot Mo de ³ 9 98048 This feature is n ot available with th e MS3580 or the MS3780. The sweet spot mode is used to determine wh ere the maximum read rat [...]

IS3480 / MS3580 / MS3780 R 5 S ECTION R IS3480 / MS3580 / MS3780 The following bar codes are spec ific to the IS 3480, MS358 0 and the MS3780 unless oth erwise noted. IR Activation IR Activation * Disable IR Activation ³ 1 23817 ³ 1 23807 TTL RS232 The following bar codes are only valid for the TTL RS 232 Quantum seri es (IS/MS3x80- 102 ). Enable[...]

IS3480 / MS3580 / MS3780 R 6 S ECTION R MS3780 The following bar codes are spec ific to the MS 3780 unless otherwise noted. CodeGate (MS3780) * Enable CodeGate Out-of-Stand, Primary Pattern Active Disable CodeGate Out-of Stand, Primary Pattern Active ³ 1 20402 ³ 1 20412 * Enable CodeGate Out-of-Stand, Secondary Pattern Active Disable CodeGate Out[...]

IS3480 / MS3580 / MS3780 R 7 S ECTION R MS3780 The following bar codes are spec ific to the MS 3780 unless otherwise noted. Modes (MS3780) Enable Normal Mo de ³ 4 18304 Enable IR Activation Mode ³ 4 18364 Enable Trigger Mo de ³ 4 18354[...]

[...]

Protocol Formatting S 1 S ECTION S P ROTOCOL F ORMATTING The following barcodes may be used for the Stratos Series and some Fusion or Voyager models. Please contact a customer service representative for additional information and technical assistance. * ROM Emulation Version 1 ROM Emulation V ersion 2 ³ 3 42100 ROM emulation ve rsion 1 is the defa[...]

Protocol Formatting S 2 S ECTION S P ROTOCOL F ORMATTING ROM Emulation Version 7 ROM Emulati on Version 8 ³ 3 42160 ³ 3 42170[...]

[...]

[...]

[...]

April 2007 Printed in the USA 00 - 02407 H[...]