Honeywell T8132C инструкция обслуживания

1 69-1635-2 OWNER’S GUIDE T8131C, T8132C Programmable Thermostat W eekday/W eek end Progr ammable Heat and/or Cool Thermostat and Mounting Plate 69-1635-2[...]

2 69-1635-2 W elcome to the w orld of comfort and energy savings with your ne w Honeyw ell Programmab le Ther mostat. Y our new Ther mostat automatically controls the temperature in y our home, k eeping you comf ort- able while sa ving energy when programmed according to the instructions in this manual.[...]

3 69-1635-2 T able of Contents P age Programming Thermostat ......................................................................................................... ...... 4 Program Schedule ............................................................................................................... ........... 6 Programming Guide ..............[...]

4 69-1635-2 Programming Thermostat When you progr am the thermostat, set one schedule for weekdays and another for weekends, because your temperature require- ments probably v ary . (During weekends, only the W AKE and SLEEP time per iods are available.) Use the personal Program Schedule for planning your program schedule of time and temperature se[...]

5 69-1635-2 Select RETURN if you w ant the house at a comfortable temperature for activities before bedtime. When deciding what time to set for your RETURN period, include extra lead time, depending on the outside temperature and your furnace response time, to give the furnace a head start to heat the house before you arrive home. (Again, higher fo[...]

6 69-1635-2 Program Schedule HEA TING PROGRAM SCHEDULE W eekda ys Start Time Heating T emperature W AKE LEA VE RETURN SLEEP W eekends W AKE SLEEP W AKE and RETURN star t times should include e xtra lead time, based on outside temper ature and furnace response time, to give your furnace a head start to heat the house. The temperatures cannot be set [...]

7 69-1635-2 COOLING PROGRAM SCHEDULE W eekda ys Start Time Heating T emperature W AKE LEA VE RETURN SLEEP W eekends W AKE SLEEP W AKE and RETURN star t times should include e xtra lead time, based on outside temper ature and furnace response time, to give your furnace a head start to heat the house. The temperatures cannot be set any higher than 88[...]

8 69-1635-2 Programming Guide NO TE: Batteries are required for operation and prog ramming. When replacing the batteries, set the system s witch to OFF . Remov e the batter y door (on the thermostat left side) using a coin at the bottom. Follow the instructions in Changing Batteries section. Set Current Time/Day To set time, press and release once,[...]

9 69-1635-2 Heating Program With the system switch at HEA T , press and release once. W AKE, MON-FRI and SET appear on display . Press to program the W AKE time and press to program the WAKE temperature f or MON-FRI. Repeat the sequence for LEA VE, RETURN, and SLEEP . Press until SA T SUN, W AKE and SET appear on the display . Press to program W AK[...]

10 69-1635-2 Cooling Program With the system switch at COOL, follow the same instructions as for Heating Program. After programming, adjust fan and system switches, as desired. Press and release to start the program. A quick guide for operating or making changes follows. NOTE: Set system s witch to HEA T or COOL to perf orm the following: T emporar[...]

11 69-1635-2 Check Current T emperature Setting —press . Check Pr ograms— press , repeatedly to see each time and temperature; then press . Cancel a program—press , until program to cancel sho ws; then press . Check Usage — press to determine length of time heating or air conditioning has been on since midnight; press again for yesterda y?[...]

12 69-1635-2 Setting Fan and System Switches First set the fan switch. AU TO : Normal setting for most homes. A single-speed fan turns on automatically with the air conditioner or fur nace. A two-speed f an usually runs on high with the air conditioner and runs on low with the furnace. ON: The fan runs continuously . Use for improved air circulatio[...]

13 69-1635-2 Changing Batteries IMPORT ANT Batteries are required for progr am- ming and operation of the thermostat and heating/cooling system. As the batteries r un low , bAt Lo indicator flashes f or one to two months bef ore the batteries r un out completely . Replace the batteries as soon as possible after the indicator star ts flashing. After[...]

14 69-1635-2 To remov e batteries, press down on the left ends of the batteries. If you inser t new batteries within 20 to 30 seconds of removing the old ones, the thermostat does not require repro- gr amming. Howe v er , if the display is blank, the batteries are dead or incorrectly installed and the thermostat requires reprogramming. • Install [...]

15 69-1635-2 T roubleshooting Guide IF… THEN… Display will not come on. ■ Set the system switch to OFF; remove batteries and insert them backward for at least five seconds to reset the thermostat; replace the batteries correctly . The display should come on. ■ Make sure the batteries are fresh and installed correctly . T emperature display [...]

16 69-1635-2 Heating will not come on (Cont). ■ If display is blank or displays bAt Lo, install fresh batteries. ■ If temperature setting is higher than current temperature, and ther mostat displa ys HEA T , contact Honeywell Customer Assistance at 1-800-468-1502. Cooling will not come on. ■ Check that the switch on the thermostat is set to C[...]

17 69-1635-2 Cooling will not come on (Cont). position. If the air conditioner comes on, the compressor could have reached its high limit temperature protection and shut down. If the air conditioner does not come on after ten minutes and displays COOL, contact Honeywell Customer Assistance at 1-800-468-1502. The house is too warm or too cool. ■ P[...]

18 69-1635-2 30% 28% 26% 24% 22% 20% 18% 16% 14% 12% 8% 6% 2% 10% 4% Minneapolis St. Paul Montreal Ottawa Toronto Buffalo Cleveland Milwaukee Edmonton Regina Winnipeg Calgary Moncton North Bay Quebec St. John's Halifax Vancouver Denver Des Moines Omaha Salt Lake City Boston Chicago Detroit Pittsburgh Indianapolis Cincinnati Kansas City St. Lou[...]

19 69-1635-2 Limited One-Y ear W arranty Honeywell w arrants this product, excluding battery , to be free from defects in the w orkmanship or materials, under nor mal use and ser vice, f or a period of one (1) year from the date of purchase by the consumer . If , at any time during the warranty period, the product is de f ective or malfunctions, Ho[...]

69-1635-2 Rev . 09-03 G.H. Pr inted in Mexico Copyright © 2003 Honeyw ell International Inc. • All Rights Reserved Automation and Control Products Honeywell International Inc. 1985 Douglas Drive North Golden Valley, MN 55422 Honeywell Limited-Honeywell Limitée 35 Dynamic Drive Scarborough, Ontario M1V 4Z9 Customer Assistance For all questions c[...]